|
LoKout posted:Those aren't eSATA ports. eSATA doesn't have the L shaped connector. See http://en.wikipedia.org/wiki/Serial_ATA#eSATA. Physically, they're standard SATA ports. However, eSATA's more than just the connector: it also uses a higher voltage to drive signals, and can deal with weaker signals, in order to make it more reliable over long distances. An eSATA port like that one should be OK with a passive adapter and a 2m eSATA cable. The same passive adapter and cable, hooked up to an ordinary SATA port inside the system, would probably have trouble dealing with the cable length. Intel's board designs are fairly rare in that they actually handle the spec correctly; many board manufacturers just toss an eSATA bracket in the box and expect you to hook it to a standard SATA controller. frunksock, you're fine. It's the same signal, it'll just work over a longer cable if it needs to.
|
# ? Mar 16, 2011 23:54 |
|
|
# ? May 10, 2024 13:17 |
|
So how many PCI-E lanes in total does the P67 have? I want to run my single graphics card at x16, but I also have a PCI sound card and will use the onboard Realtek LAN (which uses a PCI-E x1 slot).
|
# ? Mar 17, 2011 00:42 |
|
dud root posted:So how many PCI-E lanes in total does the P67 have?
|
# ? Mar 17, 2011 00:46 |
|
movax posted:VT-x support is more a function of the CPU than the chipset. The -K SKUs for example don't support VT-x, I believe. (they don't support one of the VT-* extensions, see link to my post in the OP). This is for extended page table support and the other. K-sku chips don't support VT-d even if the motherboard does. They do support VT-x (i.e. instruction virtualization). As the memory controller is on the processor, I think that's why the chip can disable a chipset feature, as it controls DMA. Factory Factory fucked around with this message at 02:59 on Mar 17, 2011 |
# ? Mar 17, 2011 01:04 |
|
dud root posted:So how many PCI-E lanes in total does the P67 have? 16 PCI-E 2.0 lanes directly from the CPU for GPUs (can be 16x1 or 8x2 config) and, 8 PCI-E 2.0 lanes from the P67 chipset, which gets used for peripherals like lan, usb3 etc. 24 Lanes in total So it seems you can leave usb3 enabled without degrading your x16 graphics connection. Having said all that, I'm sure a x8 link for graphics is still more than adequate
|
# ? Mar 17, 2011 01:25 |
|
If you're expecting a replacement sandy bridge motherboard to magically show up on your doorstep from newegg, please check your emails and don't make the same mistake I did. A little over a week ago I received an email saying that the new motherboards were starting to arrive, and to look for a notification when your replacement is avaialable. The next day I get another email from newegg; I eyeball it and write it off saying 'why would they send the same email twice?' Well, turns out that was my official notification that my replacement was in, and I had 7 business days to reply. Yesterday was day #7, and I just noticed this today. I contacted newegg via chat, and they're going to talk it over with their returns team; I may have to send my motherboard to them and then they'll send me the replacement once they get the bad one. Anyway, hope this helps someone.
|
# ? Mar 17, 2011 01:40 |
|
Thanks Space Gopher. So it seems like Q67 is actually the way to go, weird. It doesn't seem that H67 has anything that Q67 doesn't, as far as the chipset itself is concerned, and though I don't have immediate plans to use VT-d, I don't see why I wouldn't leave myself the option. This is to replace my aging home server, so I need 6 SATA ports (4 spinning disks for RAID, optical drive, and one free for now, but that I may, down the road, use for playing with SSD caching). I don't care about overclocking, I want embedded graphics, and could conceivably, at some point, want to run an intensive VM on it. For these kinds of boxes, I usually like to stick with Intel motherboards, so it looks like one of their Q67 boards with a non-K CPU will fit the bill.
|
# ? Mar 17, 2011 03:10 |
|
dud root posted:To answer my own question in case anyone else is curious: http://benchmarkreviews.com/index.php?option=com_content&task=view&id=647&Itemid=69&limit=1&limitstart=1 Yep, I posted about it about a month ago. Your PEG link is x16, bifurcatable to 2 x8. Only 8 lanes from the chipset which sucks, with the widest you can get being x4 ganged. Honestly the number of PCIe lanes is kinda lovely, but for your average consumer it is probably ok. Luckily we have X68 coming out which will have a glorious amount of PCI Express lanes, much like the X58 did.
|
# ? Mar 17, 2011 04:24 |
|
On the subject of the thread title change, is Ivy Bridge still coming out at the end of the year? And I keep reading we might get mainstream eight-core chips on socket 1155 with Ivy Bridge.
|
# ? Mar 17, 2011 05:45 |
|
movax posted:VT-x support is more a function of the CPU than the chipset. The -K SKUs for example don't support VT-x, I believe. (they don't support one of the VT-* extensions, see link to my post in the OP). This is for extended page table support and the other.
|
# ? Mar 17, 2011 06:39 |
|
Weee.... NCIX email: quote:we have an available replacement board for your GA-P67A-UD3 I guess this means I get to completely rebuild my system.
|
# ? Mar 18, 2011 22:37 |
|
Anyone see a fixed P8P67 PRO (not the P8P67-M PRO) in the wild yet? I want that Intel network adapter... and don't want to shell out for the Deluxe. I'd probably just get the MSI P67A-GD65, but only one front USB header? What the hell? Tapedump fucked around with this message at 04:38 on Mar 19, 2011 |
# ? Mar 19, 2011 04:34 |
|
Tapedump posted:Anyone see a fixed P8P67 PRO (not the P8P67-M PRO) in the wild yet? I want that Intel network adapter... and don't want to shell out for the Deluxe. Yes they have been coming in stock intermittently (mine just arrived today from amazon), but you have to act pretty quick when one shows up because it's one of the most popular boards.
|
# ? Mar 19, 2011 04:42 |
|
Ouch, $250 on Amazon right now? Now that's a gouge. I'd rather get the Deluxe from NewEgg for less. Guess I gotta wait. Edit: I hope NewEgg at least lists the ATX-sized Pro; Amazon's search for technical items kinda sucks.
|
# ? Mar 19, 2011 04:57 |
|
Tapedump posted:Ouch, $250 on Amazon right now? Now that's a gouge. I'd rather get the Deluxe from NewEgg for less. That's some third party gouger, when amazon.com actually gets it in stock its at the regular retail 189.95 price. Do people really still not understand how amazon.com works?
|
# ? Mar 19, 2011 05:06 |
|
greasyhands posted:That's some third party gouger, when amazon.com actually gets it in stock its at the regular retail 189.95 price. Do people really still not understand how amazon.com works? Apparently not. I got mine from Amazon today too.
|
# ? Mar 19, 2011 06:07 |
|
Are there any mATX P67 motherboards out there that have UEFI, USB 3.0, SATA3, and an onboard Intel NIC? The closest I can see is the Asus P8P67-M Pro, but it's missing the Intel NIC. I guess I could always just buy an Intel PCI-E NIC if need be, but I'd rather not have to.
|
# ? Mar 19, 2011 19:33 |
|
mpeg4v3 posted:Are there any mATX P67 motherboards out there that have UEFI, USB 3.0, SATA3, and an onboard Intel NIC? The closest I can see is the Asus P8P67-M Pro, but it's missing the Intel NIC. I guess I could always just buy an Intel PCI-E NIC if need be, but I'd rather not have to. Yeah, that Asus board is one of the best mATX, except for the Intel NIC being missing. Not sure if anyone else has made a mATX board that gives you the Intel NIC. I'd guess it's because of cost.
|
# ? Mar 19, 2011 20:28 |
|
I haven't had the issues with Realtek NICs that others have, but plenty of previous boards have used Marvell Yukon chipsets that worked just fine, is there a reason no one used those on their Sandy Bridge boards? I did some poking around and saw an Asrock board using an Atheros chipset, but that was it for variety. It would be interesting to know what the cost difference is between the Intel and other NICs.
|
# ? Mar 19, 2011 20:52 |
|
I had a terrible stuttering issue with the realtek chip, specifically the one that's on P8P67-M Pro. It can do large files transfers at a good speed, but as soon as you start streaming HD stuff off it, such as a 2160p test clip that uses 50+Mbps, it will slow down to a few megabits per second and the video stutters/freezes. Tried different driver, cable, switches in every combination and it was still the same, including putting an intel nic into the host. In the end the problem just disappeared when I replaced the onboard realtek nic with the intel one on the client computer.
|
# ? Mar 20, 2011 01:47 |
|
mpeg4v3 posted:Are there any mATX P67 motherboards out there that have UEFI, USB 3.0, SATA3, and an onboard Intel NIC? The closest I can see is the Asus P8P67-M Pro, but it's missing the Intel NIC. I guess I could always just buy an Intel PCI-E NIC if need be, but I'd rather not have to. Intel DP67DE?
|
# ? Mar 20, 2011 14:31 |
|
Ika posted:Intel DP67DE? I always forget about the Intel boards. What's the overclocking like on it? From what I've been able to find, it apparently is not too easy to overclock anything on it.
|
# ? Mar 20, 2011 17:52 |
|
mpeg4v3 posted:I always forget about the Intel boards. What's the overclocking like on it? From what I've been able to find, it apparently is not too easy to overclock anything on it. Probably not available on that board, but their enthusiast boards are fairly decent for non-extreme overclocking.
|
# ? Mar 20, 2011 18:20 |
|
Why would they even produce p67 boards if they were going to disable overclocking?
|
# ? Mar 20, 2011 18:34 |
|
Here is a Marvell Yukon based adapter that rocks hard. http://www.newegg.com/Product/Product.aspx?Item=N82E16833166015&Tpk=rosewill%20gigabit%20adapter For the price these things are the best you can get.
|
# ? Mar 20, 2011 19:16 |
|
Just got my bugged Gigabyte P67A-UD3 upgraded to a B3 Asus P8P67 Pro. What a difference. 4.8 GHz stable on the Asus at the same voltage as 4.7 on the Gigabyte, and looks like there's plenty of room to go up. 5.0 GHz, here I come.
|
# ? Mar 20, 2011 23:07 |
|
One thing you have to watch out for if you're going to purchase a motherboard with an onboard Intel NIC is if it supports Jumbo Frames. A lot of Intel reference boards I've purchased have the onboard Intel NIC, but research/drivers have often revealed a lack of Jumbo Frame support. I had to purchase a PCI Express Intel NIC that had Jumbo Frame support because the DP45SG's onboard Gigabit NIC couldn't do it.
|
# ? Mar 21, 2011 00:19 |
|
COCKMOUTH.GIF posted:One thing you have to watch out for if you're going to purchase a motherboard with an onboard Intel NIC is if it supports Jumbo Frames. A lot of Intel reference boards I've purchased have the onboard Intel NIC, but research/drivers have often revealed a lack of Jumbo Frame support. I had to purchase a PCI Express Intel NIC that had Jumbo Frame support because the DP45SG's onboard Gigabit NIC couldn't do it. Seems like the Sandy Bridge boards' Intel NICs support it fine. edit: intel specs http://ark.intel.com/Product.aspx?id=52963
|
# ? Mar 21, 2011 00:32 |
|
mpeg4v3 posted:I always forget about the Intel boards. What's the overclocking like on it? From what I've been able to find, it apparently is not too easy to overclock anything on it. I have the BA board, and it let me overclock the turbo multiplier, but not the base multiplier. It also is not possible to disable the autothrottle on the overclock, so it will throttle down after 10 minutes or so at turbo speeds. Other people have reported the exact same issue as well.
|
# ? Mar 21, 2011 00:52 |
|
Should I care about jumbo frames as a home desktop user? Should I enable them if its disabled?
|
# ? Mar 21, 2011 02:44 |
|
dud root posted:Should I care about jumbo frames as a home desktop user? Should I enable them if its disabled? If you use a NAS or regularly transfer files between computers over the network, yes and yes. If you just do Internet stuff, meh.
|
# ? Mar 21, 2011 02:58 |
|
1.42V for 5.0 GHz. Worth it? :|
|
# ? Mar 21, 2011 04:13 |
|
For bragging rights, sure, but not for 24/7 use. ~1.35 V is the highest you want for regular use.
|
# ? Mar 21, 2011 04:15 |
|
Factory Factory posted:For bragging rights, sure, but not for 24/7 use. ~1.35 V is the highest you want for regular use. Yeah dropped back to 4.8GHz after running the Aero evaluation at 5.0 :P Didn't improve my previous CPU score though. Still 7.7. But wow. Things are so much easier on the P8P67 Pro. Such a nice board. I totally forgot got good Asus was because I haven't had an Asus board since my T-bird days (too many cheap Fry's ECS combos). 4 USB 3.0 ports too, and Bluetooth! Wedesdo fucked around with this message at 04:31 on Mar 21, 2011 |
# ? Mar 21, 2011 04:27 |
|
Not happy with my replacement board...BSODs left and right, with a far shittier overclock than I previously had. Think I got a bad one
|
# ? Mar 21, 2011 04:39 |
|
movax posted:Not happy with my replacement board...BSODs left and right, with a far shittier overclock than I previously had. Think I got a bad one I know I got a bad p8p67-m pro. My b3 mobo kept locking. Switched the mobo out with the old rev and I haven't crashed since. Newegg can't switch it out until they get it back in stock and I have to keep track of their stock.
|
# ? Mar 21, 2011 04:48 |
|
I'm surprised by all the Asus love in here. Out of dozen or so motherboards from a half-dozen brands I've had over the years, a Socket 478 Asus board was by far the worst. I haven't bought anything they've made since. Was that just a bad model or era for them, or have they turned it around or what?
|
# ? Mar 21, 2011 05:13 |
|
Siroc posted:I know I got a bad p8p67-m pro. My b3 mobo kept locking. Switched the mobo out with the old rev and I haven't crashed since. Newegg can't switch it out until they get it back in stock and I have to keep track of their stock. Got stable now-ish, going through my crash dumps now in WinDbg. I have a feeling the Renesas controllers on this board don't like BCLK increases.
|
# ? Mar 21, 2011 05:16 |
|
The thing about brand loyalty or avoision is our minds are made up so long ago, and that doesnt take into account recent changes in manufacturing process. eg I swear by western digital harddrives as I had a couple of segates & hitachis die. But that was 10 years ago, and ignoring the fact its only anecdotal/small sample evidence, the roles could be reversed now.
|
# ? Mar 21, 2011 05:25 |
|
|
# ? May 10, 2024 13:17 |
|
I got a P8P67 Pro but couldn't post, the red led cpu light kept coming on. After digging around I found some bent pins on the motherboard. Amazon is offering me a refund but since they are out of stock they can't replace it. I guess I need to RMA through ASUS though I'm afraid it will take forever to get a replacement board.
|
# ? Mar 21, 2011 05:25 |