|
Sperglord Firecock posted:It's not a factory turbo. Then I think it is likely a 86 model year. OK, so since you seem to have a big stiffy for a Z31, here is what I would do: Either: 1: Sell the car as is (or, running decently), take money and buy and keep a look out for an unfucked Turbo Z31. They are out there and tons were sold. 2: This was touched on earlier, but maybe get a hold of the previous owner and ask him if he lowered the compression or did any internal engine modifications. Just fire him an email if nothing else. If not, bring it back to a stock NA. Do the clutch, sell the Turbo and assorted doo-dads to some sucker on ebay or something. This will also benefit you by learning to wrench by un-loving it (which you will need to do if you plan on having a mid 80s car as your DD). Bank the money and keep eyes open for a Turbo. 3: Keep car as-is and live with it. I know you are really looking at #3, but seriously give 1 & 2 thought. It's just a car and you will have another that you love even more. Trust me.
|
# ? Dec 24, 2014 19:57 |
|
|
# ? May 24, 2024 14:56 |
|
Sperglord Firecock posted:It's not a factory turbo. I didn't read that before and that changes everything, in that you paid too much and you should definitely sell it. But I'll never say that again, and I'l stop being negative from now on. I know where you're coming from because when I was 19 I bought an RX3 for $1400, had no tools and knew nothing about cars as well. And that's a car I was diving into the deep end with because I knew no one who knew about rotaries, or even cars in general, and no internet existed for me back then. Similar to the above suggestion I bought a 1300cc 808 for $300 for learning on, spare panels etc, and drove that around mainly, while figuring out the RX3 and panel work (the RX3 was a beat up stock standard 12A automatic, fair bit of rust and couple of dents. Long term plan was 13B extend port and weber, with 5sp manual.) The 1300cc 808 was a piece of crap all over, mechanically and bodywise too, and I found a mint 808 1600cc for $900. Learnt to rebuild a motor on that 1600, heads, chucked on a 32/36 weber, tuning and all that crap. Stripped the 1300cc 808 of panels, interior and glass for spares and dumped the shell. Drove the 1600cc 808 while doing the 13B and 5spd on the RX3, and getting it painted in 2pac and the rest is history, (another 808 for more spares, a $1300 RX4 coupe, and a $700 929 coupe for spares, bridgeports, extend port turbos, etc) So been there, done that, started off with no tools and knowledge as well (no gurus or helpful dad or whatever), but doing it that way was an expensive education, lots of work paid to rotomotion. I'd do it all again because these cars are worth stupid money now, but wouldn't do it with a car that's not worth much and had PO problems. Fo3 fucked around with this message at 20:07 on Dec 24, 2014 |
# ? Dec 24, 2014 19:59 |
|
Fo3 posted:getting it painted in 2pac I hope this means something similar to what I think it means. Can you post a photo of the paint?
|
# ? Dec 24, 2014 20:06 |
|
Astonishing Wang posted:I hope this means something similar to what I think it means. Can you post a photo of the paint? Murdered out euphemism? vv
|
# ? Dec 24, 2014 20:07 |
|
Edit: nope
|
# ? Dec 24, 2014 20:09 |
|
Astonishing Wang posted:I hope this means something similar to what I think it means. Can you post a photo of the paint? No photo unless you supply a time machine, it was rough bodywork done by teenage me so has since been rubbed back with proper weld in rust repairs started (but never finished)
|
# ? Dec 24, 2014 20:21 |
|
slidebite posted:If you did I missed it. I'm really not looking at 3. I plan on driving up to SouthsideSaint's place this saturday and we're gonna work on wrenching off the turbo, and hopefully I'll learn some neat stuff while I'm there. Eventually, I'll figure out the RIGHT way of getting a Turbo in there, and install a proper job of it, instead of cheap ebay.
|
# ? Dec 24, 2014 20:22 |
|
slidebite posted:Either: 4: sell it and buy a turbo II
|
# ? Dec 24, 2014 20:26 |
|
I just finished reading all the posts in this thread, and the massive amounts of schadenfreude of everything in this thread, from wanting to convert power windows to manual, to the show-off nature, to the lack of knowledge is just what I needed to un-bummer my holiday season. Thank you, Sperglord Firecock.
|
# ? Dec 24, 2014 20:32 |
|
Sperglord Firecock posted:I'm really not looking at 3. Don't go through the effort of learning/unfucking this thing just to use it to experiment on again in the future. It'll cost you way more in money and time than just buying a nice OEM car. If you are going to unfuck this (a fair idea) just keep it that way.
|
# ? Dec 24, 2014 20:37 |
|
Sperglord Firecock posted:I'm really not looking at 3. If you haven't thought of this already, you will need different exhaust bits in order to remove the turbo, generally at least the manifolds and downpipe(s?). Make sure you do your research and have appropriate parts on hand, preferably at junkyard prices. E: I should ask, is this car a twin-turbo setup or just a single? Fender Anarchist fucked around with this message at 20:47 on Dec 24, 2014 |
# ? Dec 24, 2014 20:42 |
|
Fucknag posted:If you haven't thought of this already, you will need different exhaust bits in order to remove the turbo, generally at least the manifolds and downpipe(s?). Make sure you do your research and have appropriate parts on hand, preferably at junkyard prices. Single. I'm getting secondary advice from the Z-Car forum I went to, just to double-check stuff. After all, they are kinda the experts on that kinda stuff. I'm mostly double-checking "i have this aftermarket turbo, how likely is it to blow up".
|
# ? Dec 24, 2014 21:03 |
|
Sperglord Firecock posted:I'm getting secondary advice from the Z-Car forum I went to, just to double-check stuff. After all, they are kinda the experts on that kinda stuff. I'm mostly double-checking "i have this aftermarket turbo, how likely is it to blow up". Yes, I'm sure the experts you are consulting will be able to nail down exactly how likely a motor of unknown age and mileage which may or may not have been rebuilt and if it was how well or with what parts that is running an unknown CR with an unknown turbo controlled by unknown parts is to blow up.
|
# ? Dec 24, 2014 21:10 |
|
If you really hate yourself this much- let me set you up with a Zombie SAAB (It survives only to eat parts of the living).
|
# ? Dec 24, 2014 21:10 |
|
Why does everyone care so much if he ruins the car, its not like its super rare or anything.
|
# ? Dec 24, 2014 22:47 |
|
Sperglord Firecock posted:we're gonna work on wrenching off the turbo, and hopefully I'll learn some neat stuff while I'm there.
|
# ? Dec 24, 2014 22:49 |
|
Sperglord Firecock posted:Single. Keep in mind, these are probably the same "experts" that told the PO to put that turbo in there in the first place. Specific car forums are a great place to find out some minor bit of trivia for your car or to find a nicely spelled out how-to with pictures and such, but the people are terrible and when it comes to general automotive know how, I would trust the people in AI far more. Except the nerds saying to sell it. Yank the turbo off, drive it like a madman and have fun with it.
|
# ? Dec 24, 2014 23:42 |
|
track day bro! posted:Why does everyone care so much if he ruins the car, its not like its super rare or anything. Just trying to help the guy out.
|
# ? Dec 24, 2014 23:43 |
|
mariooncrack posted:Just trying to help the guy out. Some men just want to watch
|
# ? Dec 24, 2014 23:54 |
|
track day bro! posted:Why does everyone care so much if he ruins the car, its not like its super rare or anything. Because he's young, inexperienced, and not in the financial position to undergo such an endeavor. This was a poor choice, but be can salvage some of it and learn a valuable lesson.
|
# ? Dec 25, 2014 02:05 |
|
howling_mad posted:not in the financial position to undergo such an endeavor Correction: I now have a job.
|
# ? Dec 25, 2014 03:06 |
|
Sperglord Firecock posted:Correction: I now have a job. Woohoo! Enterprise?
|
# ? Dec 25, 2014 03:52 |
|
Sperglord Firecock posted:Correction: I now have a job. Which is a good start, but do you really want to stick it all into a car project right now? You should be building an emergency fund, and looking for a reliable vehicle.
|
# ? Dec 25, 2014 03:59 |
|
Sperglord Firecock posted:Correction: I now have a job. More unsolicited advice: working a lovely job to unfuck a lovely car is not going to get you ahead in life. /more pee for the pisshole
|
# ? Dec 25, 2014 04:57 |
|
It will cost way more in parts to remove the turbo and return it to stock. Either keep the drat thing and start doing some actual research on the EFI system, or just cut your loving losses. Everyone, stop crying about "compression ratio is going to danger to manifold your engine." Times have changed, and with it, new technology and tuning theories. Stock 80s turbo cars with their low comp engines were that way because we didn't know any better. Nowadays, a high comp turbo setup is fairly common, and if done right, a beautiful thing. I tuned a 10.2:1 CR Volvo to run 24psi. I've worked on and tuned a 10.5:1 b16 Honda running 10psi. High comp turbos are awesome when it comes to off throttle response, transient response, and make great street cars. That's why I keep saying you need to check what you are running. Is it the stock efi? Turbo efi? Chipped box? Nistune? What injectors?
|
# ? Dec 25, 2014 06:07 |
|
mafoose posted:Everyone, stop crying about "compression ratio is going to danger to manifold your engine." I haven't seen anyone saying that. But not knowing means you have NO loving IDEA how to set up the engine management or determine if it was done properly in the first place.
|
# ? Dec 25, 2014 06:12 |
|
I forget why I thought this was funny. It wasn't.
West SAAB Story fucked around with this message at 18:19 on Dec 25, 2014 |
# ? Dec 25, 2014 06:25 |
|
Sperglord Firecock posted:Correction: I now have a job. Congrats, I think.
|
# ? Dec 25, 2014 08:38 |
|
mafoose posted:That's why I keep saying you need to check what you are running. Is it the stock efi? Turbo efi? Chipped box? Nistune? What injectors? I have no idea how to check that. In other news, first time someone changed my pic and message! I AM getting slightly annoyed at the ever-changing "FIX IT DON'T FIX IT" theme of the thread, though. For the person asking about an Emergency Fund, I do in fact have one of those, so I'm not particularly worried about that. Navy left me with a pretty good financial safety net. fishception fucked around with this message at 12:34 on Dec 25, 2014 |
# ? Dec 25, 2014 12:30 |
|
Haha somebody got a custom title for Christmas.
|
# ? Dec 25, 2014 17:55 |
|
Sperglord Firecock posted:I have no idea how to check that. Quoting for posterity. Everyone, this is a Slow Motion response. Note how he gives one line to the matter at hand, only to say he has no idea about it and does not show any initiative to learn about it. He uses the rest of the reply to combat attacks against his ego and point out our one discord in the unity that is "quit being a baby and put effort in". Hello AI SloMo.
|
# ? Dec 25, 2014 17:58 |
|
|
# ? Dec 25, 2014 19:09 |
|
Adiabatic posted:Quoting for posterity. Well, I mean, how DO I check it? I've got the service manual, and it states about the E.C.C.S. and the Electronic Control System in the Engine Fuel/Emission Control part, and it mentions an EFI Relay. Do I need to check on the ECCS? Do I need to check the ECS? Do I need to check the relay? What part am I going to likely have to replace? Edit: While reviewing the manual, I found what MIGHT be the issue with it idling, since I'd imagine solenoid valves, if they are anything like they are in the Navy, are finicky sons of bitches, and there's a specific solenoid that "stabilizes idle speed when engine load is heavy". fishception fucked around with this message at 20:17 on Dec 25, 2014 |
# ? Dec 25, 2014 20:11 |
|
Yeah, that's pretty normal. Increases RPM when the ac is on or you're wrenching on power steering (which loads up the engine and may cause stalling otherwise). It's the emissions control solenoids and any vacuum lines that can cause problems however.
|
# ? Dec 25, 2014 21:59 |
|
So the solenoids your speaking of. Like the one I told you about at the back of your engine with a loose wire going to it im up for helping you out. but don't expect your turbo to become a non turbo in a few beers and a mig welder. I am willing to guide you in an appropriate direction and see if anything else obvious is hosed.
|
# ? Dec 26, 2014 03:26 |
|
Motronic posted:I haven't seen anyone saying that. There has been a bunch of posts about how he should return it to stock (remove the turbo bits). I'm pretty sure the part numbers on the ecu are different between turbo and non-turbo models. Similarly the injectors should have parts numbers cast into the plastic upper part with part numbers as well. Googling that will tell you make and model they're from, or flow rates if they're aftermarket. If it has a nistune, it'll either have a connection to tune it, or if you remove the top cover, you'll see a daughter board. The reason it has idle issues is likely from the bov venting metered air, or being slightly open at idle.
|
# ? Dec 26, 2014 03:41 |
|
mafoose posted:There has been a bunch of posts about how he should return it to stock (remove the turbo bits). That seems to have more to do with this guy not having the slightest possibility of verifying if this swap was done properly or making it correct if it wasn't. Not that he has a chance in hell of reverting it to NA properly either.
|
# ? Dec 26, 2014 05:15 |
|
We're all gonna help him out though, right?
|
# ? Dec 26, 2014 07:07 |
|
mafoose posted:I'm pretty sure the part numbers on the ecu are different between turbo and non-turbo models. Similarly the injectors should have parts numbers cast into the plastic upper part with part numbers as well. Googling that will tell you make and model they're from, or flow rates if they're aftermarket. Do what this man says. If you don't know how, loving google it or look on your "specialist" forums for a DIY article. Actually do something and verify what it is you have.
|
# ? Dec 26, 2014 16:23 |
|
|
# ? May 24, 2024 14:56 |
|
Sperglord Firecock posted:I AM getting slightly annoyed at the ever-changing "FIX IT DON'T FIX IT" theme of the thread, though. I also have a Z31, and have had it for the last 6 years/55k miles. I love the car. It's not a turbo, and was mostly unfucked by the two PO's that had it before me. I have done all the work on it myself and consider myself a pretty experienced shadetree mechanic. All that being said, you have no tools or previous working knowledge, run far away. Let me explain: This is a stack of recepts for about $3-4000 dollars in parts that i've had to replace in the last 6 years to keep the car running. All done by me, no labor cost factored into that. This does not include the wrecked parts car that i also bought to pull parts from if needed. I'd advise you to sell it, buy a junker car that you don't care about, and ruin that by learning to work on cars. Don't ruin a Z trying to learn to work on cars, please.
|
# ? Dec 26, 2014 17:15 |