|
I have a portable air conditioner in my sun room that we cut a 5 inch hole for the exhaust. Trouble is we have a second one that I'd rather use and it has a 6 inch hose. I've googled like crazy and can't seem to find a reducer for these types of hoses. Any ideas?
|
# ? Jun 26, 2015 03:05 |
|
|
# ? Jun 11, 2024 18:17 |
|
tomapot posted:I have a portable air conditioner in my sun room that we cut a 5 inch hole for the exhaust. Trouble is we have a second one that I'd rather use and it has a 6 inch hose. I've googled like crazy and can't seem to find a reducer for these types of hoses. Any ideas? Cut a larger hole?
|
# ? Jun 26, 2015 03:10 |
|
tomapot posted:I have a portable air conditioner in my sun room that we cut a 5 inch hole for the exhaust. Trouble is we have a second one that I'd rather use and it has a 6 inch hose. I've googled like crazy and can't seem to find a reducer for these types of hoses. Any ideas? Duck tape?
|
# ? Jun 26, 2015 03:39 |
|
Edit: Nevermind.
|
# ? Jun 26, 2015 03:46 |
|
XmasGiftFromWife posted:Cut a larger hole? I'd rather keep the hole the same size since almost all the portable A/C units I've seen have 5 inch hoses. If I can get a way to reduce it I'm covered for whichever unit I get in the future. Also the hole was cut by the room installer and I don't want to mess with it and lose warranty or pay for him to come back out.
|
# ? Jun 26, 2015 06:03 |
|
babyeatingpsychopath posted:You're making a toilet tank, then putting a pump in it, right? I think we're all on the same page now. Except this post.
|
# ? Jun 26, 2015 06:36 |
|
tomapot posted:I'd rather keep the hole the same size since almost all the portable A/C units I've seen have 5 inch hoses. If I can get a way to reduce it I'm covered for whichever unit I get in the future. Also the hole was cut by the room installer and I don't want to mess with it and lose warranty or pay for him to come back out. http://www.homedepot.com/p/Master-Flow-6-in-to-5-in-Round-Reducer-R6X5/100170194
|
# ? Jun 26, 2015 09:27 |
|
FrankeeFrankFrank posted:
That looks like a whole lot of nothing to me. In NC, when you mark flood plains, you have to put in permanent markers. However, unless you see actual survey nails in the ground (They'll probably near the bottom two dots, and you'll see flags on your actual property corners along that line for reference points), or they start adding in more flags to that make some sort of sense, it's probably nothing? I mean, if they were going to re cut the creek, there would be a lot more flags and probably a lot of wooden stakes marking depths and cut levels. I mean, they could be doing something, but normally if they were you'd notice a lot more markers both up and down the creek as they'd definitely have to get a topograph of the area before any real engineering could be done.
|
# ? Jun 26, 2015 17:08 |
|
This seems like as good of a place as any: Cut my forearm last night real bad on a rusty car fender while changing a strut. Put some gauze on it, then a paper towel, then held it on with electrical tape. Now the gauze is like growing into the wound or some bullshit. Should I remove the gauze? I feel like this is going to make it start bleeding again but also don't want the gauze to become a permanent part of my arm. PS: No, I don't have health insurance and probably won't go to a doctor
|
# ? Jun 26, 2015 17:12 |
welp
|
|
# ? Jun 26, 2015 17:12 |
|
Nevermind I guess. The rest of the internet has me covered, need to change bandage -- who would have thought?
|
# ? Jun 26, 2015 17:15 |
I was going to suggest maybe the plumbing thread?
|
|
# ? Jun 26, 2015 17:19 |
|
Your last tetanus shot was when?
|
# ? Jun 26, 2015 17:20 |
|
Bad Munki posted:I was going to suggest maybe the plumbing thread? Normally I just wouldn't worry about it, many is a time that electrical tape and paper towels have healed my wounds. This one was really loving scary deep though and probably needed stitches. The good news is you can no longer see my arm muscle and that seems like A Good Thing <edit> tetanus shot was forced on me during an ER visit 5-6 years ago??
|
# ? Jun 26, 2015 17:21 |
apatite posted:forced on me Picture's becoming clearer.
|
|
# ? Jun 26, 2015 17:26 |
|
Bad Munki posted:Picture's becoming clearer. by "forced on me" I mean that I couldn't tell them when I last had a shot so they gave me one anyway and then charged a hilarious amount of money even though the cuts were from broken glass, not metal (I am not some rabid antivaxxer or whatever is hip these days) anyway this has been apatite derailing the quick questions thread, now back to your regularly scheduled programming
|
# ? Jun 26, 2015 17:28 |
|
Well if you wake up and can't open your jaw all the way, you probably will want to go to the doctor! I'm currently looking to do a serious shower (stall) cleaning job - cleaning/resealing the grout, and replacing all of the caulking. If I want to take off the door bracket, assuming it's screwed into anchors in the tile, is there a trick to avoiding trashing everything so I can just screw things back in once I'm done cleaning?
|
# ? Jun 26, 2015 17:53 |
|
Gothmog1065 posted:That looks like a whole lot of nothing to me. In NC, when you mark flood plains, you have to put in permanent markers. However, unless you see actual survey nails in the ground (They'll probably near the bottom two dots, and you'll see flags on your actual property corners along that line for reference points), or they start adding in more flags to that make some sort of sense, it's probably nothing? I mean, if they were going to re cut the creek, there would be a lot more flags and probably a lot of wooden stakes marking depths and cut levels. Thanks. Last night my girl said, "There were like 10 guys back there today looking at pieces of paper and pointing alot." I said, "Did you ask them what they were doing?" "No." "Did you notice any vehicles and what words or logos may have been on them?" "No." She's obviously not worried.
|
# ? Jun 26, 2015 18:56 |
|
The Gardenator posted:http://www.homedepot.com/p/Master-Flow-6-in-to-5-in-Round-Reducer-R6X5/100170194 Thanks, I went looking for something like that and could not find it. I also searched a bunch of the A/C accessories sites for something plastic. Bad Munki posted:I was going to suggest maybe the plumbing thread? Or the electrical thread if you need to cauterize it.
|
# ? Jun 26, 2015 20:01 |
|
apatite posted:by "forced on me" I mean that I couldn't tell them when I last had a shot so they gave me one anyway and then charged a hilarious amount of money even though the cuts were from broken glass, not metal (I am not some rabid antivaxxer or whatever is hip these days) Tetanus does not magically come from metal, idiot, it's naturally occurring in soil and if you get cut you are getting a vaccine if you're not up to date because there's no loving reason to not give it to you Jesus Christ why am I even bothering, you come to a DIY thread for medical advice
|
# ? Jun 26, 2015 20:16 |
|
NancyPants posted:Tetanus does not magically come from metal, idiot, it's naturally occurring in soil and if you get cut you are getting a vaccine if you're not up to date because there's no loving reason to not give it to you Thank you for the information and insults DIY thread for DIY medical advice, what could possibly go wrong?
|
# ? Jun 26, 2015 20:29 |
apatite posted:DIY thread for DIY medical advice, what could possibly go wrong? Well, tetanus, for one?
|
|
# ? Jun 26, 2015 20:31 |
|
Bad Munki posted:Well, tetanus, for one? also serious infections!
|
# ? Jun 26, 2015 20:43 |
|
Did obama make it so all americans have to have some basic insurance to cover poo poo like this?
|
# ? Jun 26, 2015 22:37 |
|
Baronjutter posted:Did obama make it so all americans have to have some basic insurance to cover poo poo like this? Or pay a penalty, yeah, and there's tax breaks / grants for low-income people. There should be some way for you to get proper medical attention on this injury without having to pay through the nose for it.
|
# ? Jun 26, 2015 22:54 |
|
apatite posted:This seems like as good of a place as any: At least see if you qualify for Medicaid.
|
# ? Jun 27, 2015 00:24 |
Dear Fix It Fast thread, Maybe you can help me out on this one, not sure where else to ask: US healthcare?????
|
|
# ? Jun 27, 2015 01:51 |
|
TooMuchAbstraction posted:There should be some way for you to get proper medical attention on this injury without having to pay through the nose for it. Yeah, but it'll probably be mostly healed anyway by the time the passport shows up in the mail.
|
# ? Jun 27, 2015 04:56 |
|
Baronjutter posted:Did obama make it so all americans have to have some basic insurance to cover poo poo like this? Most (all? I haven't checked) of the obamacare exchange plans are high deductible, so for a minor injury you'd still be paying the bill yourself.
|
# ? Jun 27, 2015 05:21 |
|
Flipperwaldt posted:The only way to remove this stuff is mechanically. I had a blob of it fall on my head last month and had to cut out sections of my hair. In the frenzy I took off my t-shirt, which got then ruined from the inside out. So my advice is to please not be an idiot like me. I'm just bringing it up because nobody else did: stuff is nasty sticky. Wear more protective clothing than just the gloves they recommend.
|
# ? Jun 27, 2015 16:08 |
|
When you're recaulking, is it OK to put new caulk over paint (that's on wood or aluminum)? Or do you have to remove all the old paint just like the old caulk? I'm preparing to recaulk the outside edges of window frames, and I know you need to get rid of the old caulk first, but I'm talking about old paint still left solidly adhering to wood or the aluminum window frame, which would be a pain to get every last bit of off. (I know you should get rid of any peeling paint there, which is easy since it's peeling, but that's not what I'm talking about).
|
# ? Jun 28, 2015 04:17 |
|
Onomarchus posted:When you're recaulking, is it OK to put new caulk over paint (that's on wood or aluminum)? Or do you have to remove all the old paint just like the old caulk? I'm preparing to recaulk the outside edges of window frames, and I know you need to get rid of the old caulk first, but I'm talking about old paint still left solidly adhering to wood or the aluminum window frame, which would be a pain to get every last bit of off. (I know you should get rid of any peeling paint there, which is easy since it's peeling, but that's not what I'm talking about). That's really up to you. For the best seal, you'd have to get down to the bare surfaces and caulk. This causes problems, like you said it's a lot of work, plus not all caulk readily accepts paint if you do want to come back and touch up the paint. Personally, I would remove absolutely all of the loose paint that you could, then caulk.
|
# ? Jun 28, 2015 05:41 |
|
I'm looking at adding some sun control window film to one side of my house to keep heat out during the summer, in during the winter, and reduce the glare from direct sunlight. I have two main questions: First, is there somewhere I can buy decent window films as a DIYer? Unfortunately all the home improvement stores around here carry the exact same limited selection of Gila films. In particular, I think I want the kind of reflective film that HOAs don't like, as I understand that provides the most efficient heat rejection (since it gets reflected out rather than absorbed), I don't care about night visibility, and my neighbors can't see the windows on this side. I know a lot of the higher-end films (3M etc) need to be professionally installed, but it seems like there's a lot of options I'm missing out on. Second, what's the truth about window films and double-pane windows? I see some places saying you can never use them because heat buildup will damage the seals, other places say that's bullshit and all but the darkest blackout film works fine. Half the windows on that side of the house are double-pane and half single-pane for some reason, and it would suck if I couldn't just use one roll to cover all of them. I don't think any of the windows are low-E or anything.
|
# ? Jun 28, 2015 20:00 |
|
I need to desolder and solder on a new faucet to the outside of my house. However there's about an inch of pipe sticking out from the wall which is covered in vinyl siding. Any suggestions for what I might want to use to keep the torch from melting the vinyl?
|
# ? Jun 28, 2015 23:09 |
|
Squibbles posted:I need to desolder and solder on a new faucet to the outside of my house. However there's about an inch of pipe sticking out from the wall which is covered in vinyl siding. Any suggestions for what I might want to use to keep the torch from melting the vinyl? Fireproof cloth. EvilMayo fucked around with this message at 23:29 on Jun 28, 2015 |
# ? Jun 28, 2015 23:21 |
|
Squibbles posted:I need to desolder and solder on a new faucet to the outside of my house. However there's about an inch of pipe sticking out from the wall which is covered in vinyl siding. Any suggestions for what I might want to use to keep the torch from melting the vinyl? Non smart-rear end answer: how about a piece of scrap whatever wood with a hole in it? (Although suppose some heat could sneak in if the hole was too big)
|
# ? Jun 28, 2015 23:23 |
|
Tyson Tomko posted:Non smart-rear end answer: how about a piece of scrap whatever wood with a hole in it? (Although suppose some heat could sneak in if the hole was too big) So you can set the wood on fire and burn a big hole in the siding?
|
# ? Jun 28, 2015 23:27 |
|
Interesting, I didn't know they made such products. I'll have to take another look around home depot or similar I guess.
|
# ? Jun 28, 2015 23:37 |
|
XmasGiftFromWife posted:So you can set the wood on fire and burn a big hole in the siding? Assuming you aren't wrapping the pipe in kindling, it'll take a fair bit for the wood to actually catch on fire. Wood has a pretty good heat capacity.
|
# ? Jun 28, 2015 23:39 |
|
|
# ? Jun 11, 2024 18:17 |
|
It can also be soaked in water for half an hour ... but fireproof cloth is probably the better way to go.
|
# ? Jun 28, 2015 23:41 |