|
Six to eight hours? Generator.
|
# ? Jan 23, 2022 23:32 |
|
|
# ? Jun 8, 2024 09:35 |
|
There are backup pumps that use your municipal water supply and the venturi effect to pump water out of a sumo. If you've a nearby water supply line, that's an option. I think the one I've seen before is called Basepump.
|
# ? Jan 24, 2022 00:19 |
|
Kingtheninja posted:So we received a notice from our power company, they're working in our neighborhood and should expect no power for about 6 hours on Thursday. Which sounds great. We have a sump pump in the basement, but have no idea what we need to keep it running without power. Generator. But why do you think you need to keep this sump pump running? Does it run all the time already (this is a different problem) or what?
|
# ? Jan 24, 2022 00:50 |
|
motronic is right if you can't shut off your sump pump for a day without moving under the sea there's another problem
|
# ? Jan 24, 2022 01:03 |
|
Mainly because I have no idea what I'm doing and am new to this. I know our pump runs a few times a day, so I assumed six hours without power would let the water level rise too high.
|
# ? Jan 24, 2022 01:36 |
|
Kingtheninja posted:Mainly because I have no idea what I'm doing and am new to this. I know our pump runs a few times a day, so I assumed six hours without power would let the water level rise too high.
|
# ? Jan 24, 2022 02:11 |
|
Unplug your pump the next time you’re going to be at home for 6 hours and keep an eye on it.
|
# ? Jan 24, 2022 03:35 |
|
My house/neighborhood is in a drained swamp off of the Delaware River, and the water table is about six inches below my basement floor, maybe a bit more in quasi-drought conditions but definitely well-below the water table if we’re getting more than average rainfall, and my my system will pull groundwater for a couple-3-weeks after the last heavy precipitation. What saves my foundation walls is that the whole area is sand. During such a period, a power loss for more than four hours would turn my basement into a koi pond. One of the reasons I have a generator.
|
# ? Jan 24, 2022 04:50 |
|
PainterofCrap posted:During such a period, a power loss for more than four hours would turn my basement into a koi pond. One of the reasons I have a generator. Don't they have water powered sump pumps for backups?
|
# ? Jan 24, 2022 06:54 |
|
kid sinister posted:Don't they have water powered sump pumps for backups? I am intrigued by these things - I have been thinking I should have some backup for my sump, since the primary time I depend on it is during storms (Bay Area CA) when it is likely our power may go out also. Now, worst thing that happens if my sump overflows is my encapsulated crawlspace floods and I have to pump it out later, so not the end of the world - just a large inconvenience. My sump is also right under the master bathroom and near the foundation wall, so I have readily accessible copper lines right there with a good discharge point. Anyone here actually have experience with them? Along the same lines, anyone have a recommendation for a good, 120V powered de-watering pump with a garden hose outlet I could throw down in the crawl space in case it does flood in the meantime (not that we might get anymore rain this season)? Figure that is the sort of thing I would rather already have on hand when needed.
|
# ? Jan 24, 2022 07:08 |
|
ROJO posted:Along the same lines, anyone have a recommendation for a good, 120V powered de-watering pump with a garden hose outlet Those requirements are mutually exclusive. You'll be lucky to flow 12 GPM through a garden hose regardless of the quality or price of the pump.
|
# ? Jan 24, 2022 13:34 |
|
kid sinister posted:Don't they have water powered sump pumps for backups? I have sleep apnea and the generator will run that, the fridges & freezers, and the pump. Probably getting one of those this year and installing it. 2021 was a fairly uneventful year for groundwater, and it hardly ran, so I get cheap/lazy...which isn't the thing to do since it all can change in a heartbeat.
|
# ? Jan 24, 2022 15:59 |
|
Slugworth posted:Like, when it's raining or just all the time? Where do you live, what's your yard like, etc? You shouldn't have a constant supply of water around your foundation. I live in the burbs outside Chicago, our area isn't great but not terrible for water. Our house has a sloped back yard at least so water drains away from it. I hear it go periodically throughout the day in normal conditions, but I'd imagine it pumps out maybe 5 or 6 times a day. I just get nervous because during the big rain falls in the summer I timed it running every 50 seconds for a few hours, so I worry 6 hours without power might let water get too high.
|
# ? Jan 24, 2022 16:02 |
|
Leperflesh posted:I remember now, you built a coffee table in the woodworking thread, right? Tell me what sorta tools you have to hand. I have a lovely handsaw that I wrecked on a few pieces of hollow metal pipe. That's about it. If I were to have tools, I'd wait until I got a whole garage to work out of. I'd considered just getting a bunch of wood outside, sawing it down to fit, and gluing it to the missing part. But then I'd have to figure out how to cut the right piece out of the wood for the latch, and eh. Will prolly just get a really long screw and fasten the latch back in and hope for the best. Also I suspect that door is why I have so many insulation issues this winter!
|
# ? Jan 24, 2022 16:27 |
|
Is there any "the basics of building a house" book, video? Generally cement brick with metal roof. If I build a house in a less developed country with no regulation, is there some sort of guild I can follow so that the roof doesn't fall down after a year.
|
# ? Jan 25, 2022 04:03 |
|
Fozzy The Bear posted:Is there any "the basics of building a house" book, video? Generally cement brick with metal roof. This isn't the right materials (it's all lumber building), but it might still be useful: Housebuilding: A Do-It-Yourself Guide. It has clear diagrams for all the various bits that go into making a house. I think if you combined that with a reputable guide for cement brick construction, you'd be in a pretty good place. Off the top of my head, the things that are important when it comes to roofs are: - The roof is built of strong enough materials to support loads: the weight of the roof deck and the roof itself (metal in your case), the weight of people walking on it, the weight of any snow that might accumulate, etc. - It's designed such that water flows off of it instead of getting stuck in crannies or flowing into cracks. For the most part this means that materials higher up the roof are installed last, so that they overlap on top of materials that are lower down. - If in an area where it freezes, the roof is steep enough that large quantities of snow can't accumulate and the risk of ice dams is reduced - If in an area with high winds, the roof is securely attached to the rest of the building (otherwise updrafts can rip the roof off the walls) - If in an area with high rainfall, gutters are installed and the runoff directed away from the building's foundation - The rafters have blocking installed between them to resist racking forces That said, I've only built one roof and it was years ago, so do not take this as any kind of expert advice. I would generally say "build your walls, then order prefabricated trusses and install them according to the manufacturer's recommendation", but trusses like that might not be available in your area.
|
# ? Jan 25, 2022 05:04 |
|
I have that book^^^^^^^ Its pretty good and I learned a lot. Though in fairness I've still never built a house yet.
|
# ? Jan 25, 2022 11:46 |
|
the washer is now so far out of balance it walked its way off a shim and tripping a sensor and halting the cycle. on top of the previous issues this may be it. Think I’d be looking at $300 of parts before this. It could be related to me messing with the column trying to clean it out but it has never been very balanced since I bought the place. They’re 30 years old, just worn out. So what’s good these days in washers/dryers? Any brands with better reliability or whatever? I don’t really mind trading feature set for cost/reliability, no need for internet gizmos to break.
|
# ? Jan 25, 2022 11:54 |
|
Working on starting to repaint over the poo poo-awful flat apartment white, and noticed that the previously painted bathroom has what looks like pubes and beard trimmings embedded in the paint, probably from the POs shaving or something before painting in there. Google is telling me how to get paint out of hair but not vice versa. Do i just take some 60 or 80 grit and sand it out before repainting in there or what?
|
# ? Jan 25, 2022 14:42 |
|
D34THROW posted:Working on starting to repaint over the poo poo-awful flat apartment white, and noticed that the previously painted bathroom has what looks like pubes and beard trimmings embedded in the paint, probably from the POs shaving or something before painting in there. yep sand it out or scrape it off with a paint scraper.
|
# ? Jan 25, 2022 15:09 |
|
Might not be the place to ask but I'll give it a try: I've got a radio HDMI receiver that is not working right. I opened it up and discovered the issue. The screw fitting for the antenna was just surface glued to the inside of the plastic case by the manufacturer and the glue failed. When the glue failed there was no mechanical means to prevent the fitting from spinning freely, which caused the wire between it and the circuit board to break. It should be a fairly simple repair, but I want to make sure that the fitting cannot spin. It's got a hexagonal base, but there's nothing in the existing plastic to grab and hold that base. Would applying JB Weld or something similar around it do the job?
|
# ? Jan 26, 2022 20:04 |
|
PremiumSupport posted:Might not be the place to ask but I'll give it a try: Picture is worth a thousand words here. Also hot glue or that silicone goop that hardens. Or a drop of solder.
|
# ? Jan 26, 2022 20:08 |
|
H110Hawk posted:Picture is worth a thousand words here. Also hot glue or that silicone goop that hardens. Or a drop of solder. Yeah, like an idiot I left my phone at work when I went home for lunch. I can post some later this evening though.
|
# ? Jan 26, 2022 20:11 |
|
Our tub was leaking into this closet for a while. I pulled off the trim to put down new lvp, and the drywall that is in contact with the backside of the trim looks like it has mold. What should I do? I think I can cut it out and just put in a small patch that won't need to be taped and mudded since the trim will go back a little higher up.
|
# ? Jan 26, 2022 23:08 |
|
lwoodio posted:Our tub was leaking into this closet for a while. I pulled off the trim to put down new lvp, and the drywall that is in contact with the backside of the trim looks like it has mold. What should I do? I think I can cut it out and just put in a small patch that won't need to be taped and mudded since the trim will go back a little higher up. I'd be more worried about what's going on on the backside of that drywall, i.e. inside the wall.
|
# ? Jan 26, 2022 23:13 |
|
Oh no. My friend..... Several years ago, me noticing a little wet patch where the wallpaper was lifting off the drywall along rhe shower led to me having to go to the studs on 2.5 walls. I was seeing the tip of the iceberg where it had finally come through the wall, and the backside of the drywall was straight up black mold.
|
# ? Jan 27, 2022 00:18 |
|
I guess I will cut the bottom couple inches off and take a look at the bottom of the 2x4s
|
# ? Jan 27, 2022 01:38 |
|
lwoodio posted:I guess I will cut the bottom couple inches off and take a look at the bottom of the 2x4s The counter argument btw, is that if this was a one time water intrusion, it has dried out, and nobody in the home has respiratory or immune issues, wiping down the outside of the wall and sealing up the wall cavity isn't the *worst* plan. Mold doesn't grow in the absence of moisture, so it's not gonna get worse, and encapsulation is a reasonable method of dealing with minor issues. You breathe in mold spores all day long, the health concern comes when your house's air ends up having a higher amount than a typical summer day.
|
# ? Jan 27, 2022 02:38 |
|
H110Hawk posted:Picture is worth a thousand words here. Also hot glue or that silicone goop that hardens. Or a drop of solder. Here's a couple shots of the device internals, AA battery included for scale. https://imgur.com/a/lTdgube There was nothing but the metal-to-plastic glue interface preventing the fitting from spinning freely, and that obviously was not sufficient. I want to do something to beef it up rather than just re-gluing it and hoping it doesn't come loose again.
|
# ? Jan 27, 2022 02:42 |
|
PremiumSupport posted:Here's a couple shots of the device internals, AA battery included for scale. I think your plan to use an epoxy like JB Weld will work just fine.
|
# ? Jan 27, 2022 02:52 |
|
Paul MaudDib posted:the washer is now so far out of balance it walked its way off a shim and tripping a sensor and halting the cycle. on top of the previous issues this may be it. Think I’d be looking at $300 of parts before this. Product recommendation thread is maybe a better spot, but I'd offer a few suggestions: Avoid anything that insists on connection to IOT or your phone to make/change settings. If you have to download an app to use the thing, pass. Along similar lines, I don't trust a phone manufacturer to make a good, large home appliance. I don't like touch screens on big equipment. Just feels like one more thing to fail. Anything you buy today is probably going to be way more efficient than what you are replacing. What brand are you replacing? I don't know if you'll get another 30 years out of it, but that's a really good run. Maybe look and see what the latest model of that is. I don't know how bad wait times are now for appliances, but it was 6+ months for me last year to get a new fridge. Same for a buddy of mine. You might either need to look far and wide, or prepare for a wait.
|
# ? Jan 27, 2022 04:18 |
|
CzarChasm posted:Along similar lines, I don't trust a phone manufacturer to make a good, large home appliance. I don’t think you really get how these giant Korean conglomerates operate.
|
# ? Jan 27, 2022 04:46 |
|
All I can add to the above: explore commercial equipment. It's usually simple, durable, and light on electronic crap.
|
# ? Jan 27, 2022 04:47 |
|
FCKGW posted:I don’t think you really get how these giant Korean conglomerates operate. Samsung should tell their appliances division to spend more on durability and less on tv's in your appliances. Their dedicated TV appliance sucks, why would you combine that with the thing that keeps your food edible longer?
|
# ? Jan 27, 2022 04:50 |
|
Can a regular person safely and responsibly install a gas fireplace? Here are the connections/controls I have (obviously i'll stop using the fireplace as a toddler bookshelf when the time comes): I live in TX and last February many people were left without power so I'm hoping to have a backup source of heat. I don't know anything about this and I am so afraid of gas that once when I was a 20-something I endured a whole winter in Dallas with no heating whatsoever because I was too scared of the open-flame wall-mounted heater my apartment had. It seems like I might be able to buy the following and DIY it together:
Am I forgetting anything? Should I hire a professional for this? Are any of my assumptions stupid?
|
# ? Jan 27, 2022 18:13 |
|
I'm hiring an electrician to install a 240V/50A outlet for charging an EV. The installation location will be somewhat sheltered, but it's still exposed enough that I want to build a box to protect it from rain. Building the box is easy enough -- backing board with a hole in it for the outlet, sloping roof, charging cord exits through a hole in the bottom, hinged cover with a latch. What I'm wondering about is water getting between the box and the wall. The siding is stucco, so not the kind of thing that I can get a piece of Z flashing into. Is this a case where I just caulk the top and sides and hope for the best?
|
# ? Jan 27, 2022 18:18 |
|
TooMuchAbstraction posted:I'm hiring an electrician to install a 240V/50A outlet for charging an EV. The installation location will be somewhat sheltered, but it's still exposed enough that I want to build a box to protect it from rain. Building the box is easy enough -- backing board with a hole in it for the outlet, sloping roof, charging cord exits through a hole in the bottom, hinged cover with a latch. What I'm wondering about is water getting between the box and the wall. The siding is stucco, so not the kind of thing that I can get a piece of Z flashing into. Is this a case where I just caulk the top and sides and hope for the best? I would just us all UL-Listed waterproof equipment and let it get rained on directly. If you're using cord-and-plug instead of hardwired then use IEC 60309 connectors like a baller. Plenty of outdoor chargers that have 0 protection from the elements. If you want to build a little house for it to be aesthetically pleasing then yeah I guess caulk it regularly and pray? Make sure you aren't enclosing it if it's not rated to be, could overheat.
|
# ? Jan 27, 2022 18:37 |
|
Corla Plankun posted:Can a regular person safely and responsibly install a gas fireplace? Gas is no harder than any other plumbing, however getting it wrong is a lot more dangerous than your average water leak. I would honestly hire out the installation. If you're doing it yourself you should know how to purge the gas line to make it safe to uncap and work with, and how to test your work for leaks.
|
# ? Jan 27, 2022 18:39 |
|
Corla Plankun posted:Can a regular person safely and responsibly install a gas fireplace? Even if you don't DIY the whole thing (and I agree that you either shouldn't, or be well prepared with leak detection and knowledge), you could do the physical install and just hire a plumber to do the piping. I got a pipe installed professionally for my stove, and it really wasn't too bad.
|
# ? Jan 27, 2022 18:43 |
|
|
# ? Jun 8, 2024 09:35 |
|
I don't remember where I heard the story of the guy purging the gas line with a vacuum cleaner and blowing up the place. Well, definitely don't do that.
|
# ? Jan 27, 2022 18:58 |