|
ijyt posted:Yes I know what the difference between ATX, mATX, and ITX is and I went through that with him, he doesn't want an ITX build because SFF sized stuff tends to be at more of a premium and he doesn't particularly care for a smaller case that sits on a desk. Might as well get a ~40L ATX mid tower then, there's a bunch of good ones to pick from.
|
# ? Aug 22, 2022 11:30 |
|
|
# ? May 30, 2024 13:07 |
|
ijyt posted:What's some good mATX cases to look for? Looking to get the boyfriend a more airflow friendly case. I'll be avoiding bottom intake due to pets and carpets. Looking for full-size GPU support, good airflow, as compact as possible without sacrificing too much 3.5" and 2.5" drive space. I just helped my nephew build in the Fractal Pop Mini Air, here's my post from the main building thread: Butterfly Valley posted:Supervised my nephew's build the other day and it went pretty painlessly, successfully booting first time. The Fractal Pop Mini Air is a decent enough case with a slightly cheaper feel than I would have hoped, with the thumbscrews to hold the side panel in being very tight and tough to screw in and out by hand. Some paint also stripped screwing in the PSU. Otherwise tons of extra space and storage capacity, clear instructions, 3 RGB fans and a decent overall look imo.
|
# ? Aug 22, 2022 11:31 |
|
VulgarandStupid posted:No one is forcing you to put fans there. Also the case can be inverted by swapping top and bottom panels if need be. You can do side intake while inverted and fans on top. Indeed — I have two of them and have done pretty much every configuration with them. They are highly versatile.
|
# ? Aug 22, 2022 12:54 |
|
ijyt posted:Yes I know what the difference between ATX, mATX, and ITX is and I went through that with him, he doesn't want an ITX build because SFF sized stuff tends to be at more of a premium and he doesn't particularly care for a smaller case that sits on a desk. Just checking! In that case i’ll double down on my fractal design recs of the define mini or meshify mini. They’re more compact tower than SFF but they hit everything else on your list in a decently small footprint for a floor-standing case, you’ll never have any compatibility problems, they’re great to build in, and - since you have pets and carpet - all the intakes are filtered, and the filters are very easy to clean. Meshify has better airflow while Define trades some airflow for noise-dampening foam on every interior surface. I’d also look at the matx motherboard situation very closely before pulling the trigger, though. There’s a compact atx model in both lines that has the same footprint and three inches more height, but full atx compatibility means you’re not restricted to the handful of matx motherboards released for a modern socket. To compare dimensions to something like that SAMA: the sama is 391 x 185 x 303mm (L x W x H), while the meshify 2 mini is 396 x 205 x 406 mm. So you’re shaving almost nothing off the length, about an inch off the width, and four inches off the top, where you probably won’t care if it’s going under a desk. And for that you get worse airflow and fewer features, though the sama is admittedly cheaper.
|
# ? Aug 22, 2022 14:24 |
|
Working on watercooling an Hyte Revolt 3. The connection from the gpu to the cpu is gonna be tough.
|
# ? Aug 22, 2022 14:39 |
|
What do people think of the Sliger Cerberus X design where the PSU can go either on the front or above the motherboard? It'd be nice to have the fans in front for airflow but that means putting the PSU on the back, which blocks a lot of airflow around the motherboard (even with an AIO there's still other components). It also looks like most people do fans on intake on the bottom. Seems like a SFX PSU is a good idea, if you can live with the capacity constraints that entails? There's less downside in either placement with a smaller PSU. Are the Corsair Platinums still the way to go? this looked like more or less the most reasonable (non-showpiece) build: Maybe use louver plates in the bottom pcie slot covers, and put some fans on top or in the front? That front being open through the framework there is going to lose a lot of static pressure, if you're trying to do positive-pressure... or maybe that's the point and they're trying to "duct" the gpu exhaust out the front? In that case maybe some fans on top too, and lose the dinky atx panel fan and replace it with a louver panel, so you've got two positive-pressure areas coming from top and bottom...
|
# ? Aug 24, 2022 02:36 |
|
So after posting in the PC build thread and getting some feedback for a potential NR200 build I realized that it's a 6L increase from my RVZ-02B. I'm thinking it's gonna be way bigger than what I want, so now I'm leaning towards the FormD T1 or something in that 10-12L range. I've updated my parts spec if anyone has any experience with this case I'd love some feedback. I've done some general googling but I trust ya'll more than some randos. Am I still in air-coolable territory at this point? Am I just being stubborn by not going for an AIO setup? I think the most intensive use case (outside of some CPU heavy work use) I have planned beyond 1440/60 gaming is DCS in VR which may or may not happen. Also any other ideas on cases would be welcome as it looks like some of the FormD stuff like the USB-C IO kit is OOS anyways, and I would like at least some form of front IO. PCPartPicker Part List CPU: Intel Core i7-12700 2.1 GHz 12-Core Processor ($342.98 @ B&H) CPU Cooler: Noctua NH-L12S 55.44 CFM CPU Cooler ($59.95 @ Amazon) Motherboard: Asus ROG STRIX B660-I GAMING WIFI Mini ITX LGA1700 Motherboard ($199.99 @ Amazon) Memory: Corsair Vengeance 32 GB (2 x 16 GB) DDR5-5600 CL36 Memory ($169.99 @ Amazon) Storage: Western Digital Black SN770 2 TB M.2-2280 NVME Solid State Drive ($198.33 @ Amazon) Video Card: EVGA GeForce RTX 3070 Ti 8 GB XC3 ULTRA GAMING Video Card ($652.05 @ Amazon) Power Supply: Corsair SF750 750 W 80+ Platinum Certified Fully Modular SFX Power Supply ($144.99 @ Newegg) Case Fan: ARCTIC P12 PST 56.3 CFM 120 mm Fans 5-Pack ($30.99 @ Amazon) Total: $1799.27 Prices include shipping, taxes, and discounts when available Generated by PCPartPicker 2022-08-23 23:21 EDT-0400
|
# ? Aug 24, 2022 04:23 |
|
How would you guys rate this prebuilt? https://www.memoryexpress.com/Products/MX00119619 I am feeling the case - I don't think I've seen many other tall ITX that are so flashy. Plus it's got USB right where I'd want it I think specs wise it could do hotter - I'd rather put a 3070 in there to go with the i7. Not a fan of no igpu either. I'm happy with DDR4 for now, but I've had RAM trauma since the days of autoexec.bat and would want 32gb. So obviously I've sold myself on not getting it, just curious what kind of cost-value you think it might offer edit: price is $CA Cool Kids Club Soda fucked around with this message at 08:51 on Aug 24, 2022 |
# ? Aug 24, 2022 08:43 |
|
The case and PSU is all proprietary, and the wattage on the PSU is cutting it pretty close. Probably not the best airflow either. I think you could build what you’re really hoping for for a bit more or similar for a bit less. Either approach to a DIY build would be significantly better than that I would wager. Here’s me messing around a bit: PCPartPicker Part List CPU: Intel Core i7-12700 2.1 GHz 12-Core Processor ($450.50 @ shopRBC) CPU Cooler: be quiet! Pure Rock 2 Black CPU Cooler ($85.66 @ Amazon Canada) Motherboard: ASRock Z690M-ITX/ax Mini ITX LGA1700 Motherboard ($230.86 @ Vuugo) Memory: Corsair Vengeance LPX 16 GB (2 x 8 GB) DDR4-3200 CL16 Memory ($72.98 @ Amazon Canada) Storage: Western Digital Blue SN570 1 TB M.2-2280 NVME Solid State Drive ($104.99 @ Amazon Canada) Video Card: Gigabyte GeForce RTX 3070 Ti 8 GB GAMING OC Video Card ($829.00 @ Canada Computers) Case: Cooler Master MasterBox NR200 Mini ITX Desktop Case ($106.57 @ Amazon Canada) Power Supply: Corsair SF750 750 W 80+ Platinum Certified Fully Modular SFX Power Supply ($199.95 @ Vuugo) I Total: $2080.51 Prices include shipping, taxes, and discounts when available Generated by PCPartPicker 2022-08-24 08:28 EDT-0400
|
# ? Aug 24, 2022 13:34 |
|
There’s no real point to a Z motherboard without a K processor to go with it. Otherwise that build looks solid.
|
# ? Aug 24, 2022 13:56 |
|
Cool Kids Club Soda posted:How would you guys rate this prebuilt? It's going to be loud, that 12700f won't ever turbo and the GPU will be fairly toasty. There's not too many options for console style cases that will let you pack that much performance without drawbacks though.
|
# ? Aug 24, 2022 14:05 |
|
That 500w PSU - yikes. Totally missed that one edit: actually, good chance to ask, is a Platinum PSU worth the price over Gold if you're someone who leaves the computer on almost all the time? Cool Kids Club Soda fucked around with this message at 14:51 on Aug 24, 2022 |
# ? Aug 24, 2022 14:48 |
|
You like higher or lower bills?
|
# ? Aug 24, 2022 16:18 |
|
I am sorry if I turn this into a derail since I know micro ATX isn't really SFF anymore in most cases. But I disagree with the statement that micro ATX isn't useful. It cuts off a good chunk from the mainboard and the cases in particular are a really good blend between functionality and size. This will depend heavily on how you use it though. My cmopouter stands on my desk, and a functional shape is really useful there. If I want a full size ATX board, my only options at this moment seem to be mid towers (too tall for me) or huge cubes, which are too tall and too wide. I have a fractal node 804 at the moment. It's low enough that I can still comfortably put things on it if my work space gets cluttered. And while it is a little wide, it is compatible full size PSUs and GPUs and the build process is a breeze. That all being said -- next year I'm looking towards some hardware upgrades. Are there any rivals to the Fractal Define Node 804 right now that give similar usefulness in a slightly smaller package? I don't need drive bays, for instance.
|
# ? Aug 24, 2022 16:19 |
|
Cool Kids Club Soda posted:That 500w PSU - yikes. Totally missed that one If it is idling most of the day, assuming you leave the default power settings in place, it will likely make zero measurable difference. 80 plus Gold and Platinum testing doesn’t test below 20% of a PSUs rated load at all, and nearly all PSUs in the sub-10% load range are very lossy. Of course, in real terms, if your computer is only drawing 25w, losing an extra 8w isn’t really the end of the world. Likely a better focus would be to get a good unit with a 10+ year warranty that you won’t want/have to replace with your next build. That would save significantly more money, energy, and raw resources in the long run, even if it is more costly now. The calculus might be different if you are are running the thing Hogs Out 24/7 doing folding or something though.
|
# ? Aug 24, 2022 17:01 |
|
Thanks all, the Define/Meshify, and Pop Air Mini's were pretty much the ones I gravitated too - that build post is handy too thanks! I'm still trying to convince him to go ITX to be honest, especially from a space saving POV.
|
# ? Aug 24, 2022 17:05 |
|
Lord Stimperor posted:I am sorry if I turn this into a derail since I know micro ATX isn't really SFF anymore in most cases. What functionality would you be missing with a mITX board that mATX provides? If anything, the latter usually end up worse equipped because consumers view mATX more as a cost saving measure than a form factor.
|
# ? Aug 24, 2022 17:23 |
|
Cool Kids Club Soda posted:That 500w PSU - yikes. Totally missed that one Imo yes, especially for sff. The price difference is pretty minor now and maybe more important than the power savings, you get less heat in the case. Arzachel posted:What functionality would you be missing with a mITX board that mATX provides? If anything, the latter usually end up worse equipped because consumers view mATX more as a cost saving measure than a form factor. this is it for me. If you do care about height, the difference between itx and matx is bigger than the difference between matx and atx, and you don’t pay any more or lose any functionality these days. if you don’t care about height there’s no reason to go matx.
|
# ? Aug 24, 2022 17:55 |
|
Cool Kids Club Soda posted:edit: actually, good chance to ask, is a Platinum PSU worth the price over Gold if you're someone who leaves the computer on almost all the time? If we're talking about corsair gold vs platinum then the cost is worth it imo. The platinum sf have better braided cables and a better fan curve. If you're building itx you're already not going full budget build so you might as well splash out for the better unit.
|
# ? Aug 24, 2022 18:05 |
|
Arzachel posted:What functionality would you be missing with a mITX board that mATX provides? If anything, the latter usually end up worse equipped because consumers view mATX more as a cost saving measure than a form factor. the use case I can see is a) you really like 3.5" drives so having a bigger-than mITX box is necessary, and or b) you need more than one PCI-E slot
|
# ? Aug 24, 2022 18:25 |
|
hypnophant posted:Imo yes, especially for sff. The price difference is pretty minor now and maybe more important than the power savings, you get less heat in the case. While true, people should know what to expect for the price difference. At 100% full load, the difference between Gold and Plat is 2%. 87% minimum vs 89%. And most SFF case designs smartly dump the PSU heat outside of the case. All things being equal, I wouldn't spend a lot extra for Plat vs Gold. If the specific Plat unit has other things that make it more worthwhile in the long term though, like warranty or cables or higher capacity which makes you incline to keep it longer, thats likely the better choice.
|
# ? Aug 24, 2022 18:27 |
|
Cygni posted:While true, people should know what to expect for the price difference. At 100% full load, the difference between Gold and Plat is 2%. 87% minimum vs 89%. And most SFF case designs smartly dump the PSU heat outside of the case. Going from 13% efficiency to 11% equals a 15% reduction in the energy consumption, and heat output, of the psu specifically (at full load ofc). It’s admittedly not a large change in the output of the complete system, but it’s a significant difference in the specific component. You can decide what that’s worth to you but imo it is well worth the $10 or $20 difference most brands seem to charge
|
# ? Aug 24, 2022 20:12 |
|
Helps that the Corsair platinum SFX specifically is considered to be a very good PSU
|
# ? Aug 24, 2022 20:40 |
|
I didn't realize it's only about a $20 difference in a lot of places. I was all set up to bemoan wanting to look ahead in terms of energy prices & heat, but how it hasn't affected me enough to justify paying a premium on something more efficient and That's a small enough difference in cost that, relative to a whole outlay, is pretty insignificant. Although people on a small enough budget that they need to seriously factor in electricity and air con bills are already going to be looking for the cheapest possible unit they can afford right now. Oh wait
|
# ? Aug 24, 2022 20:49 |
|
Higher efficiency power supplies also tend to be quieter since they generate less heat, which is another benefit. And many SFF cases don't dump the heat outside the case. You often see cases where the power supply is shoved wherever the case designers could fit it. For example, the recent Lian Li Q58 or the ever popular NR200. From the pc building thread: That kind of PSU mount is not uncommon. Dr. Video Games 0031 fucked around with this message at 23:41 on Aug 24, 2022 |
# ? Aug 24, 2022 23:37 |
|
Fair enough. Again, I’m not saying they are worthless, I’m saying people should know what the value for their dollar really is. Small, is generally the answer. If it’s super cheap or there are other benefits, great! But the difference between gold and plat, all other things being equal, is very small. If the choice is between $50 for a PSU with a plat instead of gold or the next step up on GPU, the GPU is going to be the better option in my book 9 times out of 10.
|
# ? Aug 24, 2022 23:55 |
|
I feel like anything over $25 difference starts hitting diminishing returns for value hard. That's before tax anyway, and I'd want to see some bigger numbers before I'd consider it a must have at those prices
|
# ? Aug 25, 2022 00:14 |
|
For sff I think heat is more of a constraint than money for many people. Often there’s not any way to spend another $50 to get more power for less heat or noise in the same size of graphics card (extreme undervolting and underclocking or lowered power limits are a bit unpredictable). The people making the builds out there with a pair of standalone noctua fans aren’t going to resent getting 5-10W of efficiency savings with no tradeoffs besides the extra dollars literally being traded for it. Of course there’s no reason for any given person to follow the tastes of the market if they don’t match theirs, but the taste of the custom sff market does tend that way.
|
# ? Aug 25, 2022 20:31 |
|
For the most part once you are in SFF you are deliberately pursuing not-price-optimal outcomes.
|
# ? Aug 25, 2022 21:53 |
|
Cygni posted:Fair enough. Again, I’m not saying they are worthless, I’m saying people should know what the value for their dollar really is. Small, is generally the answer. If it’s super cheap or there are other benefits, great! But the difference between gold and plat, all other things being equal, is very small. The marginal benefit of $50 extra spent on gpu, which probably only buys you a small clock speed increase, is also very small. If your $50 or $20 can either save you a few watts (and an accompanying degree and a decibel or two) or buy you a handful of extra fps, for you that might be the gpu 9 out of 10 but it would probably be the efficiency for me
|
# ? Aug 26, 2022 05:22 |
|
Oop, found a contender for an mATX case. I think if mATX can provide more USB IO which he needs, I'll just go for that. ITX boards will undoubtedly be out of the budget. https://www.asus.com/Motherboards-Components/Gaming-Cases/PRIME/ASUS-Prime-AP201-MicroATX-Case/
|
# ? Aug 26, 2022 11:29 |
|
Lian Li/SSUPD announced the "Meshroom S," the successor to the Meshilicious: https://www.ssupd.co/products/meshroom-s?variant=41860124180664 It appears to be much the same as the Meshilicious except with an extra fan/radiator rail (allowing up to 2x 280mm rads), tweaks to the motherboard standoffs for easier cable management, and extra pump mounting locations for custom loop water cooling. I don't think there are any other differences, so the Meshlicious design will still hold up for a normal AIO setup. The "Meshroom D" was also mentioned in the press release, but no details were given other than it will be 14.97 liters (as opposed to the S's 14.93 liters) and it's coming soon.
|
# ? Aug 29, 2022 08:39 |
|
ssupd. meshlicious. and now the meshroom. how do they keep doing it folks
|
# ? Aug 29, 2022 09:08 |
|
Mushroom D I wish there were more cases that did the more vertical height for a smaller desktop footprint thing. Like if the Sliger SV590 or the Meshilicious had ATX mobo support (as in grew taller) that'd be my dream case and be tall enough for a vertical 4x120 rad.
|
# ? Aug 29, 2022 09:13 |
|
The Mushroom S already supports ATX boards.
|
# ? Aug 29, 2022 10:08 |
|
Oh wow, you're right. I missed that detail. I wonder how that works.
|
# ? Aug 29, 2022 10:27 |
|
Dr. Video Games 0031 posted:Lian Li/SSUPD announced the "Meshroom S," the successor to the Meshilicious: https://www.ssupd.co/products/meshroom-s?variant=41860124180664 The Meshroom D is a traditional layout case: https://www.reddit.com/r/SSUPD/comments/vbm3r9/meshroom_d1_found_on_nonpublished_ssupd_page/
|
# ? Aug 29, 2022 11:33 |
|
Oh, so it's just an all-mesh NR200?
|
# ? Aug 29, 2022 11:35 |
|
Dr. Video Games 0031 posted:Oh, so it's just an all-mesh NR200? So it appears
|
# ? Aug 29, 2022 14:09 |
|
|
# ? May 30, 2024 13:07 |
|
from reddit: quote:W360 designed and named the Meshlicious for SSUPD and allegedly SSUPD didn't pay out the full compensation that was promised. As a result W360 ended the partnership and filed a lawsuit against them.
|
# ? Aug 29, 2022 21:07 |