|
I want a kindling wedge! I’ve seen nail kickers for removing nails, and I’ve used a smoothing hammer to drive spikes for landscape Timbers.
|
# ? May 21, 2023 17:06 |
|
|
# ? May 15, 2024 03:47 |
|
Sarah Cenia posted:what's the coolest air hammer accessory out there? Hearing protection.
|
# ? May 22, 2023 01:57 |
|
wesleywillis posted:Hearing protection. Good point, also glasses. Air hammer work can get messy
|
# ? May 22, 2023 02:34 |
|
The 18" long bits that astro pneumatic makes. The extra reach is a god send a lot of the time. Also, if you are rocking a spring retainer, a quick change chuck is a worthwhile upgrade.
|
# ? May 22, 2023 13:02 |
|
Bought a cheap set of hammers and dollies, wasn't finished very nicely so I polished them up myself. Will have to see how it stands up to actual usage, the dollies look like they might be cast iron. There's the original surface on another dolly too for comparison.
|
# ? May 27, 2023 16:43 |
|
Suggestions for snap ring pliers? I have a cheap set with interchangeable jaws that has worked okay, but I've been fighting with the pins on the jaws being slightly oversized (and not fitting into holes on snap rings) and keeping the interchangeable jaws on the handles when they're in use since the jaws aren't positively retained in any way. Been fighting with my current set on a project, is there anything worthwhile that isn't $SnapOn money?
|
# ? May 30, 2023 20:39 |
|
I'd just use some sandpaper
|
# ? May 30, 2023 21:19 |
|
I've got the Channellock set that I mention every time this comes up. I mostly bought it for the biggest size that I used for some turbo dis/assembly work, but they're way nicer than the cheaper set of Craftsman ones I have with the interchangeable tips. They weren't cheap, but not overly expensive either. https://a.co/d/aPkwPzt
|
# ? May 30, 2023 21:54 |
|
I am not the biggest shill for Ryobi-branded tools since I use them all day for work, but Home Depot has a pretty killer deal for batteries right now. 2 pack of the regular 4 amp hour batteries with a charger for $99, plus a free tool from a list which can also be another, different 2 4ah battery pack. 4 large tool batteries for $25 apiece is real good. Splitting hairs, these are the regular output 4ah batteries and not the high output ones - it’s kinda snake oil between the two IMO. If you want a free tool instead of the battery avoid their fine knife, I’ve had two of those cheapo ones die before my boss caved and bought the more expensive one.
|
# ? Jun 8, 2023 10:24 |
|
In Canada the deal is one 4ah battery and charger plus one tool, or one more battery. for 149
Powershift fucked around with this message at 17:22 on Jun 8, 2023 |
# ? Jun 8, 2023 17:11 |
|
Powershift posted:In Canada the deal is one 4ah battery and charger plus one tool, or one more battery. for 149 The deals here have somehow become even more garbage since the pandemic. I need to make a trip down south and hit up Harbor Freight/HD/Menards
|
# ? Jun 8, 2023 18:08 |
|
Is there a decent namebrand pair of safety wire pliers out there, that's also a reasonable price? I hate my Harbor Freight ones. They're very hard to lock, and they don't like to hold onto the wire. Google (and Amazon) seem to mostly, only pull up cheapo models, or $120+ aircraft tools.
|
# ? Jun 11, 2023 08:30 |
|
Going through some old things and ran across my dad's drafting stuff, probably from college or early 70s Bunch of weird calculus specific slide rules and other stuff made in like, Denmark and Japan, but this one really stood out. It lives in a manilla envelope with like six different guys names on it crossed out, presumably this got passed around 1 River Rd in Schenectady is GE's long time research campus This was probably used to develop/design the original mammograms which used a high energy photographic process that was later chemically developed in a traditional dark room Hadlock fucked around with this message at 01:08 on Jun 12, 2023 |
# ? Jun 12, 2023 01:05 |
|
Need a metric hex socket set that goes between 2mm and 10mm (the stuff I'm working with has a bunch of 2mm and 2.5mm fasteners that need to be torqued accurately). Any suggestions on a decent set that isn't too pricey? The HF stuff only goes down to 3mm.
|
# ? Jun 12, 2023 04:47 |
|
Nohearum posted:Need a metric hex socket set that goes between 2mm and 10mm (the stuff I'm working with has a bunch of 2mm and 2.5mm fasteners that need to be torqued accurately). Any suggestions on a decent set that isn't too pricey? The HF stuff only goes down to 3mm. Maybe some Bondhus keys: https://www.zoro.com/bondhus-9-piece-metric-l-shape-hex-key-set-12299-12299/i/G3610461/ Eklinds are fine too and sold at a lot of hardware stores.
|
# ? Jun 12, 2023 05:00 |
|
nitsuga posted:Maybe some Bondhus keys: https://www.zoro.com/bondhus-9-piece-metric-l-shape-hex-key-set-12299-12299/i/G3610461/ Sockets, not keys. I've never seen a 2mm socket. You can find 2.5 in some tiny sets, but nothing smaller. You can get nut drivers in those sizes, but no torque attachment.
|
# ? Jun 12, 2023 12:34 |
|
Nohearum posted:Need a metric hex socket set that goes between 2mm and 10mm (the stuff I'm working with has a bunch of 2mm and 2.5mm fasteners that need to be torqued accurately). Any suggestions on a decent set that isn't too pricey? The HF stuff only goes down to 3mm. I have the one from ifixit, it's decent.
|
# ? Jun 12, 2023 13:14 |
|
I'm assuming he meant internal hex. Even a M1 nut is 2.5mm. It's going to be easier to get a decent hex bit set vs sockets on a budget. Eg. Wiha 79256 and pair it with a torque screwdriver or a 1/4 or 3/8 square to hex bit adapter if you want to use a torque wrench.
|
# ? Jun 12, 2023 13:16 |
|
Tekton makes a 1/4 drive set, but it goes 2-8mm. They don't seem to make a 10mm in 1/4 drive to match, only 3/8. And their 3/8 drive sockets start at 3mm. They also don't have a 2.5mm, you almost might have to look at a bit socket and a hex bit set?
|
# ? Jun 12, 2023 13:24 |
|
If it's just for torquing, maybe get a 3mm or 4mm socket with a piece of 1mm bar stock and glue it in one or more sides depending Alternately, get someone to 3d print you a 4mm socket and line the inside edges with 1mm bar stock What the hell are you building that requires accurate torque specs at 2mm and not just using loctite
|
# ? Jun 12, 2023 18:04 |
|
You can get a nice computer/phone repair set and use adapters to use the 2mm with a torque wrench I guess but I have no idea how much that would throw it off accuracy wise
|
# ? Jun 12, 2023 22:33 |
|
https://www.wihatools.com/products/hex-bit-sockets
|
# ? Jun 12, 2023 23:54 |
|
I need a tubing flaring kit, mainly for ISO/Bubble flares. I've used a million of the garbage-tier kits. What's a good one?
|
# ? Jun 13, 2023 00:08 |
|
0toShifty posted:I need a tubing flaring kit, mainly for ISO/Bubble flares. I've used a million of the garbage-tier kits. What's a good one? I got this thing and it’s quite good: TGR Professional Brake Line Flaring Tool- 45 Degree Set - Single, Bubble, and Double Flares https://a.co/d/101fYdt Available under many generic brands like any other fine Chinese product. You can also get 37 degree dies.
|
# ? Jun 13, 2023 01:55 |
|
Thanks all going to try a Wiha hex set I found online for fairly cheap. Hopefully it's not fake...
|
# ? Jun 13, 2023 04:21 |
|
0toShifty posted:I need a tubing flaring kit, mainly for ISO/Bubble flares. I've used a million of the garbage-tier kits. What's a good one? Buy the nicest one you can afford. This isn't for you since you're already on the other end of this. Once you make one brake line it's over for you. You're going to replace entire cars worth from here on out. Once you've seen how easy it can be and the condition of a three decade old brake line you'll do it as a part of that cars first brake job. Next time I get a project car I'll probably get one that is currently around $250. K tool, maatercool, Eastwood something like that.
|
# ? Jun 13, 2023 04:34 |
|
Worth noting, I bought a "does all the kinds of flares" kit off Amazon years ago and had to use it finally a few months ago and it sucked poo poo at making ISO bubble flares. Like so bad I gave up. I bought a premade parts store line that was long enough and had the right diameter bubble flare, cut the other end off, put the nuts I needed on it and flared the other end to the spec I needed instead of buying another tool that also would suck.
|
# ? Jun 16, 2023 02:06 |
|
I often contend that many DIYers are put off doing brake bending/flaring because they rent a tool from Autozone or wherever that is clapped out beyond recognition. It is quite a revelation when you use a decent tool.
|
# ? Jun 16, 2023 03:57 |
|
Between a decent tool and using cunifer I have no objection to doing brake lines anymore except when I forget to put the nut on before flaring.
|
# ? Jun 16, 2023 04:01 |
|
kastein posted:Between a decent tool and using cunifer I have no objection to doing brake lines anymore except when I forget to put the nut on before flaring. This is the way. I have no idea who the gently caress buys cheap brake line when the cunifer is so much easier to work with. Plus it's easier on the flaring tools.
|
# ? Jun 16, 2023 04:51 |
|
Youtuber Fitzee has got this tool, or jig that is basically two pipes of different sizes that are butted together and welded, with enough space to insert 18ga sheet metal between them. He uses this to make roundovers and similar features. It looks like a real simple and handy tool, but does it have an actual name? Well poo poo. I found this video, by Fitzee himself on making said tool. So th s whole post is now pointless. But I will still post it for sharings sake: https://www.youtube.com/watch?v=_uz9DqmP8PI A pipe anvil is what it's called. I could've used one of those recently.
|
# ? Jun 16, 2023 06:40 |
|
kastein posted:Between a decent tool and using cunifer I have no objection to doing brake lines anymore except when I forget to put the nut on before flaring. That's not my main problem. My problem is letting the nut fall down before I do the bend and it can't make it around it.
|
# ? Jun 16, 2023 22:47 |
|
I HATE it when I do that. I've mostly learned not to at this point.
|
# ? Jun 16, 2023 23:13 |
|
Colostomy Bag posted:That's not my main problem. My problem is letting the nut fall down before I do the bend and it can't make it around it. Electrical tape, happened to me too many times to count. StormDrain posted:Next time I get a project car I'll probably get one that is currently around $250. K tool, maatercool, Eastwood something like that.
|
# ? Jun 17, 2023 14:43 |
|
My experience with Eastwood is they are selling the identical generic tools, they just have support and a warranty. Sometimes that’s worth the extra 10-20% over buying it from a rando on eBay. I will usually save the money.
|
# ? Jun 17, 2023 17:18 |
|
I bought this one and it slaps. Per recommendations from AI. https://www.summitracing.com/parts/oes-24364
|
# ? Jun 17, 2023 21:46 |
|
I think I only have a couple of things from Eastwood, a DA polisher and a Bead roller come to mind. They both have a general sense of quality to me a step above mid grade HF tools. I'm not sure how to put it but in general they are of a good quality, the holes line up, threads are clean. For the bead roller it doesn't deflect much. You know when you're using a lovely tool and it is getting the job done and you think it's a difficult job, then you try it again with a name brand tool and it goes a lot smoother because of qualities of the tools you didn't know were important or how to recognize them? These tools have those qualities. I'd be cautious on cheap dies not being sized right and having a hard time getting fittings to fit and seal properly. And I don't think I could measure them or figure it out before I spent hours and wasted material. I'm not project farm, as you can see.
|
# ? Jun 18, 2023 03:20 |
|
Harbor freight can always be a wild ride, but the transport dollies and the little franklin carts are goddamn legit. Bought this little guy https://www.harborfreight.com/16-in-x-28-in-aluminum-folding-platform-truck-58301.html and it fucks. Moved almost my entire apartment with this thing besides the large furniture, and honestly if I could wrangle it on there myself and strapped it in I probably could have done that to. Stable as hell, folds up easily, if anything I should have put the steering wheels in the back and not the front (or got a set of casters to have it zero turn. Was gonna orignally go for a regular dolly but this thing held more by itself easily, could take laundry baskets and oddball stuff, and folds up to be almost nothing. 100% would buy again, or buy a slightly bigger one. Thing just became a staple in my household and will be great for getting things around. And it didnt put much stress on my lovely joints. Only thing I might complain about is that I would put bigger wheels on it which eh, likely just silly thoughts. Imagining it with big air tires lol. But a legit complaint is that the handle could be more secure because it does have some bend to it when pushing, much more when pulling. Much like the toolboxes (I miss my tool cart I had when I worked at my last shop I left and sold) a legit surprise that helped me out a ton this week while moving.
|
# ? Jun 25, 2023 06:23 |
|
UCS Hellmaker posted:Harbor freight can always be a wild ride, but the transport dollies and the little franklin carts are goddamn legit. Bought this little guy https://www.harborfreight.com/16-in-x-28-in-aluminum-folding-platform-truck-58301.html and it fucks. Moved almost my entire apartment with this thing besides the large furniture, and honestly if I could wrangle it on there myself and strapped it in I probably could have done that to. Stable as hell, folds up easily, if anything I should have put the steering wheels in the back and not the front (or got a set of casters to have it zero turn. Was gonna orignally go for a regular dolly but this thing held more by itself easily, could take laundry baskets and oddball stuff, and folds up to be almost nothing. at work i frequently use a Magna-Cart (brand) Flatform Cart (model) which is similar but plastic. the wheels fold up under it, so it sits flat when collapsed, which i like cause i usually keep it in my trunk along with one of those collapsible "insta-crate" things
|
# ? Jun 25, 2023 08:22 |
|
|
# ? May 15, 2024 03:47 |
|
Raluek posted:at work i frequently use a Magna-Cart (brand) Flatform Cart (model) which is similar but plastic. the wheels fold up under it, so it sits flat when collapsed, which i like cause i usually keep it in my trunk along with one of those collapsible "insta-crate" things that looks nice, just would be worried it wouldnt take as much abuse since its plastic. I abused the absolute poo poo out of that harbor freight cart and it held up hell of a lot better then I expected
|
# ? Jun 25, 2023 12:17 |