Elder Postsman posted:cheap chisels are v good for that. i used a couple for my router and grooving planes P.S. are these OAK
|
|
# ? Nov 30, 2023 02:55 |
|
|
# ? Jun 10, 2024 20:58 |
|
grooving plane is beech with a hickory wedge. router plane is douglas fir with a jatoba wedge
|
# ? Nov 30, 2023 02:58 |
|
so the way id done it is: * big hole through a block of wood * drill a cross-hole to accept an eye bolt * file a v-groove to allow the iron to rest nice & secure * grind down an allen key to act like an iron * eye bolt goes in cross-hole, iron goes through eye bolt, iron sits in groove, tighten eye bolt with wing nut the problem was that no matter how tight it was, the cutter would move under pressure, and self-feed into the work leaving big gouges inside the work. So it was a menace and i got rid of it.
|
# ? Nov 30, 2023 02:58 |
Gotta use a wedge. They're time tested
|
|
# ? Nov 30, 2023 03:10 |
Here's the plane w the fence and depth stop installed: And here's a rabbet it cut: It works pretty good imo
|
|
# ? Nov 30, 2023 03:11 |
|
I’ve been meaning to put a fence on my grooving plane but I’m worried I’ll gently caress it up
|
# ? Nov 30, 2023 03:22 |
There's nothing to gently caress up. Put some stationary screws in the plane and add wood rectangles with slots cut in them. Easy peasy lemon planey. Even if the screws or slots aren't perfectly placed you can still easily adjust them to work
|
|
# ? Nov 30, 2023 03:25 |
Posting some more I made a grooving plane It cuts the groove. I could probably tune it up a bit but it gets the job done
|
|
# ? Dec 14, 2023 09:40 |
Jewish woodworking folk song: dado dado dado, I made you out of clay dado dado dado, I play with you all day
|
|
# ? Dec 14, 2023 09:45 |
|
oh hey heres my grooving plane. if u clamp a board to the side, itll cut a 1/4” groove 1/4” deep 1/4” away from the edge. If you want it farther from the edge just put a rabbet in the fence board.
|
# ? Dec 14, 2023 09:51 |
i like big escapements and i can not lie
|
|
# ? Dec 14, 2023 11:38 |
|
i gave no blood to the table saw today
|
# ? Jan 15, 2024 01:04 |
|
anyway, today’s project was just making a couple simple sleds. finished the miter sled, started on the cross-cut sled
|
# ? Jan 15, 2024 02:01 |
|
rjmccall posted:anyway, today’s project was just making a couple simple sleds. finished the miter sled, started on the cross-cut sled post pix my man
|
# ? Jan 15, 2024 02:35 |
|
rotor posted:post pix my man here you go, my crappy little miter sled on my amateurish workbench rjmccall fucked around with this message at 05:10 on Jan 15, 2024 |
# ? Jan 15, 2024 05:05 |
|
all my jigs look like that too, its fine and normal
|
# ? Jan 15, 2024 08:29 |
|
it’s spelt gigs
|
# ? Jan 15, 2024 09:25 |
|
It's spelled spelled
|
# ? Jan 15, 2024 09:47 |
|
wtf
|
# ? Jan 15, 2024 10:14 |
|
humiliating
|
# ? Jan 15, 2024 10:14 |
|
PokeJoe posted:Finished my rock tumbler post the smooth rocks
|
# ? Jan 15, 2024 17:55 |
|
I found a cookie cut for like 50 bux a couple weeks ago. Sanded the black stain someone had put on it and it turned out beautifully.
|
# ? Jan 16, 2024 07:18 |
|
would eat
|
# ? Jan 16, 2024 07:31 |
polyester concept posted:post the smooth rocks i made this jade pendant
|
|
# ? Jan 16, 2024 08:03 |
|
i like it
|
# ? Jan 16, 2024 08:06 |
I made my gf this fossil one too but I didn't use the tumbler for it
|
|
# ? Jan 16, 2024 08:37 |
|
I was planning some boards when
|
# ? Jan 18, 2024 16:14 |
|
she plane on my board til i
|
# ? Jan 18, 2024 16:43 |
|
bomb-rear end soup
|
# ? Jan 18, 2024 16:49 |
|
lol
|
# ? Jan 18, 2024 20:37 |
|
dont doxx me bro
|
# ? Jan 19, 2024 07:43 |
|
oh sorry. imagine i posted this one instead https://i.imgur.com/2ZNJ1yw.mp4
|
# ? Jan 19, 2024 08:48 |
|
thats also me
|
# ? Jan 19, 2024 08:55 |
|
Sagebrush posted:oh sorry. imagine i posted this one instead wait till the end!!!
|
# ? Jan 19, 2024 09:20 |
xpostPokeJoe posted:I made my buddy a jewelry box for his wife. Lid is stone inlay
|
|
# ? Jan 22, 2024 03:20 |
|
goddamn that looks great
|
# ? Jan 22, 2024 03:56 |
rotor what card scraper burnisher do you have
|
|
# ? Feb 6, 2024 00:53 |
|
PokeJoe posted:xpost you’re quite good at something worthwhile
|
# ? Feb 6, 2024 01:01 |
|
PokeJoe posted:rotor what card scraper burnisher do you have i got whichever one woodcraft has then i got this one and i really like it https://www.unionmfgco.com/accuburr
|
# ? Feb 6, 2024 01:36 |
|
|
# ? Jun 10, 2024 20:58 |
$40
|
|
# ? Feb 6, 2024 01:42 |