|
Gtr is like that. Changing intake/IC piping or downpipes is challenging. New turbos means dropping the engine out, and you had better be sure there are no oil/water line leaks before it goes back together.
|
# ? May 12, 2015 19:42 |
|
|
# ? Jun 8, 2024 19:29 |
Throatwarbler posted:...so, the same as any Honda VTEC engine? You have no idea how vtec works, shut up. Every other vvti/L system works by hydraulic pressure operated by a single solenoid. This system uses individual solenoids per cylinder. Even BMW's infinitely variable valve lift system uses one actuator to operate a shaft that changes the lift ratio of all the intake lifters at once. jamal posted:Gtr is like that. Changing intake/IC piping or downpipes is challenging. New turbos means dropping the engine out, and you had better be sure there are no oil/water line leaks before it goes back together. Are you referring to the RB26 or the new gtr? Cause I didn't find the RB26 all that difficult. Lots of cunty little lines that like to sprout leaks, but that's par for the course for every 90's nissan. VQ30DETT is way worse.
|
|
# ? May 12, 2015 19:52 |
|
PitViper posted:Three months old, I installed this tire myself back in Feb. Sorry dude, I'm not giving you any more "road hazard" claims on your tires. I told you you needed an alignment last time you were here. I wouldn't have thought those Titan 59/80R63's came with road hazard.
|
# ? May 12, 2015 20:01 |
|
jamal posted:Just the exhaust manifold I think. Also it might be a new ford engine that's like that. Well a turbo integrated into the manifold has been done before, toyota did it with the last version of the 3sgte and dont gt-r's have the same setup?
|
# ? May 12, 2015 20:13 |
|
edit: gently caress, beaten by minutes...CommieGIR posted:This isn't new, a lot of manufacturers integrate the hot side into the manifold now. Toyota was doing this in the last generation of the 3sgte in the late 90's. It's too bad since the engines are cheaper than the previous generations to buy, but they basically only came with automatic transmissions. I was thinking about picking one up for my celica, but the swap is more of a pain in the rear end.
|
# ? May 12, 2015 20:17 |
|
Negromancer posted:edit: gently caress, beaten by minutes... Is that a picture after an engine fire?
|
# ? May 12, 2015 20:46 |
|
veedubfreak posted:Is that a picture after an engine fire? My subaru engine from New York looked like this.
|
# ? May 12, 2015 20:56 |
|
PitViper posted:Three months old, I installed this tire myself back in Feb. Sorry dude, I'm not giving you any more "road hazard" claims on your tires. I told you you needed an alignment last time you were here. Um excuse you the road definitely created this hazardous condition, ergo it falls under road hazard. /customerlogic
|
# ? May 12, 2015 21:58 |
|
veedubfreak posted:Is that a picture after an engine fire? Yes, a very very slow drawn out fire that oxidizes every metal object on the car over a span of 20 years.
|
# ? May 12, 2015 22:43 |
|
Powershift posted:Yes they are, look at the shape of the valve cover in the top pic. gently caress me. I just saw the ring of bolts in the crank pulley. God drat it VW. E: Throatwarbler posted:It's Audi's variable valve lift system. charliemonster42 fucked around with this message at 23:20 on May 12, 2015 |
# ? May 12, 2015 23:02 |
|
Well my 05 Sti's transmission decided to explode.
|
# ? May 12, 2015 23:15 |
|
^ #1 Son's '05 LGT trans also went kablooey.
|
# ? May 12, 2015 23:57 |
|
jamal posted:Just the exhaust manifold I think. Also it might be a new ford engine that's like that. The Pentastar does this, but only on the driver's side I think.
|
# ? May 13, 2015 02:07 |
|
Slavvy posted:Your next car should always be a honda, toyota, mazda or nissan. All other brands are garbage, and nissan is pushing the boundaries and might get booted out of the club if they aren't careful. Nissan is a pile in every direction except the GTR which I consider the Viper of Chrysler as where they dont associate with eachother.
|
# ? May 13, 2015 04:38 |
|
Safety Dance posted:First generation Escalades were a far cry from the gaudy tackmobiles we see today. I can't get over how large the bumper gap is for a publicity photo. It even looks like it's bigger on the closer side but maybe that's just perspective tricking me.
|
# ? May 13, 2015 05:09 |
|
Uthor posted:I once drove over a freshly tarred road on my bike and got that poo poo caked on everywhere. It smoked and smelled from getting heated up by the engine for a long time. When I was a kid our minivan was unlucky enough to have a plastic shopping bag melt itself to the exhaust. That smelled awful for a month +. To this day when I run over a bag I glance in my rear-view and breathe a sigh of relief when I see them exit.
|
# ? May 13, 2015 05:12 |
|
Longinus00 posted:I can't get over how large the bumper gap is for a publicity photo. It even looks like it's bigger on the closer side but maybe that's just perspective tricking me. That era was one where GM was soaking so deep in SUV cash that they gave little to no fucks about anything.
|
# ? May 13, 2015 05:43 |
|
Longinus00 posted:I can't get over how large the bumper gap is for a publicity photo. It even looks like it's bigger on the closer side but maybe that's just perspective tricking me. When my dad bought a Z71 Suburban my first reaction on seeing it was "I think it was in an accident..." He told me that was normal and I refrained from further comment (Random Google image) The Royal Nonesuch fucked around with this message at 06:48 on May 13, 2015 |
# ? May 13, 2015 06:45 |
|
Clearly, you haven't seen how big GM thinks panel gaps can get and still be acceptable. See: every Saturn ever made.
|
# ? May 13, 2015 06:48 |
Preoptopus posted:Nissan is a pile in every direction except the GTR which I consider the Viper of Chrysler as where they dont associate with eachother. I wonder if there's a large quality discrepancy between the nissans north america get and the nissans australasia and japan get because, flimsy interiors and CVT aside, they're considered pretty good around here and I haven't had many negative experiences with them. They've definitely gone backward since the 90's though, much more so than any other japanese brand. some texas redneck posted:Clearly, you haven't seen how big GM thinks panel gaps can get and still be acceptable. I remember my mate's uncle got himself an (at the time, around 2010) brand new VE holden commodore. I asked him why drove around with the bonnet popped. "It's not open, it just looks like that cause the bonnet doesn't sit right! There's a recall or something but I'm too lazy to take it in and get it fixed." This was on a car that was marketed as having, amongst other things, the smallest panel gaps of any GMH vehicle to date!
|
|
# ? May 13, 2015 08:15 |
|
<old joke> A body engineer from Land Rover goes on an exchange visit to Toyota in Japan and watches the engineers developing the latest Land Cruiser bodyshell. He notices that on the workbench they have a cat in a small cage and he asks what it's for. The Japanese engineer tells him when they have finished a Land Cruiser they lock a cat in it and go home. If the cat is dead when they return in the morning they know the shutlines on the doors are up to their high standards. The LR guy likes this idea and when he gets back to Solihull he takes a cat to work and locks it in a Defender and goes home for the night. When he returns in the morning the cat is gone. </old joke>
|
# ? May 13, 2015 09:36 |
spog posted:<old joke>
|
|
# ? May 13, 2015 10:53 |
|
some texas redneck posted:Clearly, you haven't seen how big GM thinks panel gaps can get and still be acceptable. Or ball joint tolerances for that matter.
|
# ? May 13, 2015 12:40 |
|
I honestly don't know why people care about panel gap. As long as they're even, it's the last thing in my mind.
|
# ? May 13, 2015 16:25 |
|
Panel gap is an obvious sign that build quality may be shoddy. e. Also: my drag coefficient!
|
# ? May 13, 2015 16:32 |
|
Safety Dance posted:Panel gap is an obvious sign that build quality may be shoddy. My avatar is a good sign of how much i value build quality.
|
# ? May 13, 2015 16:35 |
|
Ozmiander posted:My avatar is a good sign of how much i value build quality. Your avatar is a Jeep, not a Land Rover...??
|
# ? May 13, 2015 17:53 |
|
The Royal Nonesuch posted:When my dad bought a Z71 Suburban my first reaction on seeing it was "I think it was in an accident..." I once road tripped from Oregon to Illinois in one of these with 7 big, smelly dudes for a college SAE competition. By the end of the trip it was pretty much a huge fart prison. It also could barely haul our fat asses along with our double car trailer. Any sort of incline was an immediate drop to 35.
|
# ? May 13, 2015 18:15 |
|
Saw this one on the way into work just now Passenger had a look through the windows as we passed them later on. Nothing in the back. It drove as well as you'd expect.
|
# ? May 13, 2015 18:33 |
|
Slavvy posted:I wonder if there's a large quality discrepancy between the nissans north america get and the nissans australasia and japan get because, flimsy interiors and CVT aside, they're considered pretty good around here and I haven't had many negative experiences with them. They've definitely gone backward since the 90's though, much more so than any other japanese brand.
|
# ? May 13, 2015 19:25 |
|
My coworker has had the CVT in his 2009 Rogue replaced three times already.
|
# ? May 13, 2015 19:46 |
|
Icedude posted:Saw this one on the way into work just now
|
# ? May 13, 2015 20:11 |
|
Something electrical broke on the Fiat? gosh the surprise. Luckily a good old lobotomy will sort out the alarm woes. It hides down here Very secure. Disconnect all the parts AISS tool of the gods Obligatory. Try waking us up at night now you bastard. cakesmith handyman fucked around with this message at 20:15 on May 13, 2015 |
# ? May 13, 2015 20:11 |
|
Cakefool posted:
Glad to see it's getting a workout, it's my #1 most handy tool I own.
|
# ? May 13, 2015 20:18 |
|
I don't like the socket set on top of the engine like that though. One wayward nudge with the elbow and you get to spend the next ten minutes trying to extract sockets from greasy nooks and crannies deep inside the engine bay. Then you finish and notice one is still missing. I always put my unused tools on the ground.
|
# ? May 13, 2015 20:21 |
xzzy posted:I don't like the socket set on top of the engine like that though. One wayward nudge with the elbow and you get to spend the next ten minutes trying to extract sockets from greasy nooks and crannies deep inside the engine bay. Really, screw putting anything up on top like that. Ask me about the time I spent 20 minutes fishing around with a magnetic grabber trying to find the battery bolt I knocked in which I would've been capital F hosed without. The worst sound is the metallic ting ding....and then no sound of it hitting the ground.
|
|
# ? May 13, 2015 20:33 |
|
xzzy posted:I don't like the socket set on top of the engine like that though. One wayward nudge with the elbow and you get to spend the next ten minutes trying to extract sockets from greasy nooks and crannies deep inside the engine bay. gently caress socket trays in general, I keep them on rails. Easier to take underneath a vehicle, you can't spill them, and you can hang them up on pegboard or organize however you want with whatever ratchets you want. Just watch out when someone is helping you, for some reason no one else can seem to grasp "put it back on the rail you gently caress I don't want my poo poo disorganized".
|
# ? May 13, 2015 20:39 |
|
Yes I'm a terrible mechanic with terrible habits. The top of that engine is thoroughly flat though. Thinking of getting one of these when I've moved, just to avoid exactly what's been mentioned:
|
# ? May 13, 2015 21:18 |
|
I LOVE the racks - I keep most of my sockets on them. I also have a rolling cart with a set of racks in it that I use to hold tools currently being used on what I'm working on. I go apeshit if stuff isn't organized.
|
# ? May 13, 2015 21:22 |
|
|
# ? Jun 8, 2024 19:29 |
|
Tommychu posted:My B14 Sentra was both horrendous (like worse than my AL Sportage in build quality and reliability) and Mexican, but the B14 200SX which IIRC was shipped from glorious Nippon never seems to get poo poo on. Sorry dude, as a caretaker of a B14 200SX I can both confirm its American (TN) manufacture and general shittiness. Sub par parts, cut rate engineering and lazy styling combine to make a car that was forgettable.
|
# ? May 13, 2015 21:32 |