|
I'm about to need to drive a lot of staples into wood. I have six chairs I need to re-web. The cushions are fine, but the cheap rubber webbing woven through to support them is no match for six D&D-playing teenage boys. That's at least 8 straps per chair, to be attached twice per end (you staple the webbing on once, then double it over and staple it again), for a total of at least 800 staples needing to be driven through jute webbing into wood. My research tells me what the pros use is some sort of pneumatic stapler; this is well out of my price range. The options are: 1. Well-made hand staple gun. Pros: Drives staples with sufficient force. Cons: That's 20 pounds of force applied by my fragile ladyhands, every time I need to cock the lever. Times 800 staples. I foresee no good here. 2. Electric staple gun. Pros: Less damage to ladyhands. Cons: Every single Amazon review says these can't drive staples for poo poo, unless into very soft wood. 3. Rent a compressor, a hose, and a nailgun (can't find anybody who rents pneumatic staplers locally). Pros: has the power for the job. Cons: Expense, noise, having to learn how to operate complex equipment on the fly, with bonus chance of amusing permanent injuries if I screw things up. Are there any options I'm missing here? Do you have suggestions? I'm about ready to grumble and pay somebody to reweb the chairs, but I think I'd enjoy doing this one myself if I don't have to go broke on tools beforehand.
|
# ? Nov 27, 2014 03:35 |
|
|
# ? May 30, 2024 14:04 |
|
If you go the regular staple gun route, make sure to position your work so you're just leaning into it instead of squeezing the handle with your hand. I'd go the pneumatic route, but I already have a compressor.
|
# ? Nov 27, 2014 04:24 |
|
I have an electric stapler. Arrow staples don't work for poo poo but whatever that other brand of staple is that comes in a plastic case, works okay. Still have to tap one down occasionally. Also have a hand stapler but I rarely use it.
|
# ? Nov 27, 2014 05:25 |
|
Which brand of electric do you have?
|
# ? Nov 27, 2014 06:47 |
|
Arsenic Lupin posted:Which brand of electric do you have? Ironically it's Arrow brand. wormil fucked around with this message at 09:09 on Nov 27, 2014 |
# ? Nov 27, 2014 09:04 |
|
I got an electric brad gun that drives staples, that seems to have the muscle for the job but I don't have the brand or model handy. E: Amazon history: tacwise 181els cakesmith handyman fucked around with this message at 11:04 on Nov 27, 2014 |
# ? Nov 27, 2014 11:01 |
|
Arsenic Lupin posted:
Compressors and staple/nail guns aren't particularly complex or dangerous. You can pick up a small low powered compressor fairly cheaply. They're pretty handy to have around as well.
|
# ? Nov 27, 2014 20:41 |
|
So, is this Lowes DeWalt miter saw $78 better than the harbor freight one? http://www.lowes.com/pd_122210-70-DW715_0__?AID=10926682&PID=4328635
|
# ? Nov 27, 2014 22:40 |
|
canyoneer posted:So, is this Lowes DeWalt miter saw $78 better than the harbor freight one? The HB one is a sliding miter and it has a frickin' LASER on it.
|
# ? Nov 27, 2014 23:08 |
|
I know the general consensus is that portable table saws are no good. If I have the option of a portable or nothing, would the Kobalt table saw currently on sale for $200 be worth considering? For perspective, I've been using a cordless 5.25" circular saw for the last seven years, so I'd guess even a bad table saw would be a vast improvement.
|
# ? Nov 28, 2014 01:25 |
|
Thoughts on this compressor? http://yuma.craigslist.org/tls/4781192897.html The thing runs and has air, I don't think I can go too far wrong for 100 bucks.
|
# ? Nov 29, 2014 02:37 |
|
snickles posted:I know the general consensus is that portable table saws are no good. If I have the option of a portable or nothing, would the Kobalt table saw currently on sale for $200 be worth considering? Any table will be 10x better than that. Personally I'm a home depot guy and I saw the portable ridgid for the same price. Might want to compare them.
|
# ? Nov 29, 2014 21:02 |
|
You generally get what you pay for in table saws. Cheaper saws will be louder, with sloppy miter slots, and fences that won't stay parallel to the blade. edit: https://www.youtube.com/watch?v=BPSLsI3t_Uw wormil fucked around with this message at 06:11 on Nov 30, 2014 |
# ? Nov 30, 2014 01:15 |
|
Is there any reason to be wary of a second-hand pancake compressor? As far as I can figure, brand-new small compressors run $100 and upward, and I can find second-hand Porter Cable compressors with hoses on Craigslist for ~$50. This, for instance: http://sfbay.craigslist.org/eby/tls/4758754926.html
|
# ? Nov 30, 2014 04:02 |
|
Nothing wrong with used compressors. As long as it doesn't look like it's been running nonstop for a year doing a house remodel, go for it. Are you sure you need a pancake compressor? Good for a brad nailer/finish nailer and filling car tires but not much else. e: beat me on the edit. I don't really hate pancake compressors, they just get used a lot for things they can't do well. Hypnolobster fucked around with this message at 04:10 on Nov 30, 2014 |
# ? Nov 30, 2014 04:06 |
|
What's wrong with pancake compressors? All I need to run is a staple gun, and not at a rapid clip. It's for reupholstery, not for construction.
|
# ? Nov 30, 2014 04:08 |
|
Just check and make sure there isn't any corrosion in the tank. You can do this by running it for a little while and then draining it using the purge valve.
|
# ? Nov 30, 2014 06:59 |
|
wormil posted:You generally get what you pay for in table saws. Cheaper saws will be louder, with sloppy miter slots, and fences that won't stay parallel to the blade. Maybe I am a big ninny, but watching his hand position on those first few cuts made me cringe a little bit.
|
# ? Nov 30, 2014 14:53 |
|
asdf32 posted:Any table will be 10x better than that. Thanks for this. My local Home Depot only had the cheaper ryobi saws on display when I went to look. That ridgid looks like a better saw. Not a huge amount of information about it, but it seems quality.
|
# ? Nov 30, 2014 15:30 |
|
I have become interested in taking cheap crap tools and turning them into something usable. I have fixed up a groz 60 1/2 block plane and a no 5 jack plane to the point that they are really nice. Not lee valley quality, but certainly no worse than any of the vintage Stanleys I've had a chance to play with when tuned. Also made a couple crap sets of butt chisels usable. I am currently working on turning a hf no 33 1/2 into a scrub plane and making a set of bench chisels. After that, though, I am kind of at a loss. Has anyone made a wood smoother or infill plane? I'm tempted to just go straight to the infill since I have access to a machine shop.
|
# ? Nov 30, 2014 16:46 |
|
SkunkDuster posted:Maybe I am a big ninny, but watching his hand position on those first few cuts made me cringe a little bit. Me too. My dad nearly lost his thumb on Christmas Eve 6 or 7 years ago because he got too comfortable with his table saw.
|
# ? Nov 30, 2014 17:33 |
|
Gounads posted:Me too. Watched for this. Yes, this was bad. Not sure if he sped the video up or not but (and this is a judgement) that guy looked way to comfortable with his saw
|
# ? Nov 30, 2014 17:52 |
|
It drives me nuts to not see people wear correct PPE. I work for a big manufacturing company (not on the floor) and they are nuts about it. They even send us emails this time of year about safe practices for hanging up Christmas lights. It takes, like, 4 seconds to put on eyes, ears, and gloves. But all the PPE in the world can't correct unsafe practices.
|
# ? Nov 30, 2014 18:11 |
|
SkunkDuster posted:Maybe I am a big ninny, but watching his hand position on those first few cuts made me cringe a little bit. I posted it because he plainly shows what I wrote about sloppy miter gauges and rip fences. But the constant safety nagging everytime a tablesaw video comes up on any forum is super annoying. Personally I give no fucks if someone cuts off every one of their fingers. If a person cares about themselves they will take precautions.
|
# ? Nov 30, 2014 19:37 |
|
wormil posted:I posted it because he plainly shows what I wrote about sloppy miter gauges and rip fences. I think folks take issue because the video poster is taking a position of instruction and showing the world how they do things regarding table saws. If they are cavalier at home and off youtube no one cares, but when beginners are likely to see ther attitude towards safety, it is different.
|
# ? Nov 30, 2014 19:43 |
|
Cross posted from the woodworking thread although in retrospect probably is better here. Small update: I picked up a Dewalt finishing blade at lowes for half off so I'll give that a try. Doctor Zero posted:I'm not sure if I should post this in the tools thread or here but...
|
# ? Nov 30, 2014 22:37 |
|
Mercury Ballistic posted:I think folks take issue because the video poster is taking a position of instruction and showing the world how they do things regarding table saws. If they are cavalier at home and off youtube no one cares, but when beginners are likely to see ther attitude towards safety, it is different. The only person responsible for your personal safety, is you. And I have news for you, there are lots of videos on youtube of people who talk about safety and on the surface appear to be using a tablesaw properly but are not and making subtle mistakes that are more likely to get themselves hurt than the guy in the video. Danger is not always obvious. And even when people are using saws safely, there were will still be people who want to talk about safety; it gets so, so tiresome. Bottom line, go to a credible source for instruction on safe procedure.
|
# ? Nov 30, 2014 23:56 |
|
canyoneer posted:It drives me nuts to not see people wear correct PPE. I work for a big manufacturing company (not on the floor) and they are nuts about it. They even send us emails this time of year about safe practices for hanging up Christmas lights. I thought the advice was no gloves for anything with moving blades? No issue with the other advice, one of the foreman I used to work with on a previous job was happy for people to steal ppe for home use, if it meant you turned up to work with all your fingers and eyes
|
# ? Dec 1, 2014 00:02 |
|
I got those two 44" HF tool chests like I had previously said. Initial impressions are all very very good. I could have used one or two slightly deeper drawers so I could put my circular saw in but my routers fit and I now have a permanent enclosed place to put the vast majority of my stuff, which feels good.
|
# ? Dec 1, 2014 14:03 |
|
Anubis posted:I got those two 44" HF tool chests like I had previously said. Initial impressions are all very very good. I could have used one or two slightly deeper drawers so I could put my circular saw in but my routers fit and I now have a permanent enclosed place to put the vast majority of my stuff, which feels good. Glad you are happy with them. I like mine as I mentioned before. There is a side cabinet attachment (which I do not have) that would probably accommodate your circular saw if you want to pick it up in the future. This thing.
|
# ? Dec 1, 2014 15:15 |
|
Cakefool posted:I thought the advice was no gloves for anything with moving blades? Probably. Like I said, I'm a hobbyist so I have no idea. But not knowing something won't stop me from arguing on the internet about it!
|
# ? Dec 1, 2014 16:26 |
|
So HF wouldnt take a 20% off coupon on any of the BF items. The coupons says "not valid for in store events" which probably was what got me. The 12" compound slider is $139 which is probably the lowest it's going to get but I decided to pass because I was a little butt hurt over the coupon. I did pickup an M12 rotary tool at Home Depot for $79. Been waiting on this one for a while now, have been surprised how often I use my lovely Dremel one.
|
# ? Dec 1, 2014 18:21 |
|
Quick update... I bought that fiskars x27 axe and tried it out today. There was a world of difference that I wasn't prepared for. In the beginning, I was throwing as much force behind it as the old axe. I ended up splitting a small log, and also the stump underneath it I was using as a stand. After that, I figured out just the weight of the axe was usually enough for the easy stuff. I had a stack of wood I had tried and given up splitting with my old axe. I was convinced I'd have to break out the wedge and sledge hammer. All knotty and y-bend stuff. This thing went through those with a max of 2 strikes each.
|
# ? Dec 2, 2014 18:53 |
Can someone please find that video of the guy in sandals demonstrating his "strong" "stronger" and "strongest" log splitting attacks? I'm not having any luck and it's so topical.
|
|
# ? Dec 2, 2014 18:59 |
|
Bad Munki posted:Can someone please find that video of the guy in sandals demonstrating his "strong" "stronger" and "strongest" log splitting attacks? I'm not having any luck and it's so topical. I know exactly what you're talking about, I have gifs on my computer at home Edit: Found it https://www.youtube.com/watch?v=EgyQQGPZwrk Uncle Enzo fucked around with this message at 19:17 on Dec 2, 2014 |
# ? Dec 2, 2014 19:07 |
|
Sointenly posted:So HF wouldnt take a 20% off coupon on any of the BF items. The coupons says "not valid for in store events" which probably was what got me. Honestly you're better off IMO. I used a 12" compound slider (not mine) when putting up a deck and it just felt like garbage.. On day 2 I grabbed my $99 Hitachi non-slider and did 90% of the work with it instead of the HF one. I can't remember the particulars. but it was hard to keep straight, it was out of adjustment a lot. The guard was being a pain in the rear end for larger pieces of wood. the exhaust port clogged up quickly.. I already have an old sears rip saw so the slider isn't a big deal to me but honestly if I needed to cut something wider than my 12" could cut normally I'd pull out my circular saw and go from there. Rotary tools are amazing.. one of those things you keep saying to yourself "when am I really going to use this" then you get one and it gets used a lot more. On my list next is one o them thurr fancy oscillating tools.
|
# ? Dec 2, 2014 19:32 |
Uncle Enzo posted:I know exactly what you're talking about, I have gifs on my computer at home Thank you so much, I'd been looking for that for a while and the recent axechat reminded me.
|
|
# ? Dec 2, 2014 19:41 |
|
Uncle Enzo posted:I know exactly what you're talking about, I have gifs on my computer at home Where did this come from? Does anyone actually split wood like this (other than this guy)? He is taking 10 ft. leaps while swinging an 8 lb. maul over his head, in sandals.
|
# ? Dec 2, 2014 19:51 |
armorer posted:Where did this come from? Does anyone actually split wood like this (other than this guy)? He is taking 10 ft. leaps while swinging an 8 lb. maul over his head, in sandals. Uhhh hello do you know literally nothing about splitting wood??? https://www.youtube.com/watch?v=oadLuyIyjlI
|
|
# ? Dec 2, 2014 20:01 |
|
|
# ? May 30, 2024 14:04 |
|
armorer posted:Where did this come from? Does anyone actually split wood like this (other than this guy)? He is taking 10 ft. leaps while swinging an 8 lb. maul over his head, in sandals. I have no idea, the dude probably tried to impress his buddies one day when he was 14 and it stuck. His other videos are good too, there's a good one that (as I recall) has him using a winch to pull down a quite large tree, which falls close enough to him that he has to outrun the tree. Dude's an idiot who thinks he has found a better way to swing an axe than the rest of us mortals.
|
# ? Dec 2, 2014 20:05 |