|
Seen some reviews saying the Kobalt are pretty drat good.
|
# ? Jun 19, 2020 14:44 |
|
|
# ? May 30, 2024 13:16 |
|
I have a giant honkin' Husky toolbox and it's great. Got it fairly cheap ($600?) on black friday a few years ago. Edit: This guy: https://www.homedepot.com/p/Husky-61-in-W-18-Drawer-Combination-Tool-Chest-and-Rolling-Cabinet-Set-in-Gloss-Black-H61CH6TR12/304016203
|
# ? Jun 19, 2020 14:48 |
|
What are good ways to keep track of sockets? Are socket rails the way to go?
|
# ? Jun 19, 2020 14:51 |
|
I like the peg trays like these guys. Only complaint is the spacing can be a hair tight for impact sockets. Not enough to not work, but a little tight.
|
# ? Jun 19, 2020 14:54 |
|
I got an Ernst "socket boss" tray with 3 rails for my tool tote setup and it rocks. The twist-lock feature of the rails is a godsend.
|
# ? Jun 19, 2020 15:06 |
|
ThinkFear posted:I like the peg trays like these guys. Only complaint is the spacing can be a hair tight for impact sockets. Not enough to not work, but a little tight. Do these lock the sockets in place or do they just stay by gravity? Achtane posted:I got an Ernst "socket boss" tray with 3 rails for my tool tote setup and it rocks. The twist-lock feature of the rails is a godsend. The socket boss looks pretty good, I like that it's not just one rail.
|
# ? Jun 19, 2020 15:19 |
|
taqueso posted:Do these lock the sockets in place or do they just stay by gravity? Gravity, not the thing you want for a mobile kit.
|
# ? Jun 19, 2020 15:50 |
|
Any opinion on skillsaws? Can’t decide if I want a rear handle model or not. Mostly concerned about which type is safer.
|
# ? Jun 20, 2020 18:03 |
|
street doc posted:Any opinion on skillsaws? Can’t decide if I want a rear handle model or not. Mostly concerned about which type is safer. My experience has been that the rear handle/ worm drive design is safer because from that angle, your entire arm acts as a shock absorber rather than a bronco rider on top of 2 1/2 horses. That's a bit of a dramatic imagery, but so is one of those sumbitches running wild from a kickback.
|
# ? Jun 20, 2020 18:38 |
|
Hey guys, thought this would be the best thread to ask this question on. Basically I'm looking for an electric hand tool that will do multiple jobs. Primarily I want to use it as an electric screwdriver, but I'd also like for it to be a drill and use it for light dremel cutting. All of this will be light work, I'm not planning on building a house with it and primarily I'd be using it to pull apart/put back together electronics (laptops, etc) so I wouldn't want it to overtorque screws. Anything that can do all these things? EDIT: Primarily I imagine the issue is that a dremel needs fairly high RPM, and I don't think screwdrivers/drills will normally get that high? I am not a DIY person so I don't really know.
|
# ? Jun 20, 2020 23:41 |
|
Yeah you'll need two separate tools. Rotary tools spin at super high rpms compared to something like a drill / driver.
|
# ? Jun 20, 2020 23:50 |
|
Dremels and drivers are fundamentally different tasks; dremels have high RPM but low torque and drivers are the opposite. You need two tools.
|
# ? Jun 20, 2020 23:52 |
|
One of them being a screwdriver set not a drill/impact. Electronics do not need a power tool to take apart/put together. Its not faster and the bits are generally too big to fit into the little holes. Honestly if you want something to make life easier get a Wera set with magnetic heads.
|
# ? Jun 21, 2020 00:41 |
|
JEEVES420 posted:One of them being a screwdriver set not a drill/impact. Electronics do not need a power tool to take apart/put together. Its not faster and the bits are generally too big to fit into the little holes. When I used to do laptop repairs as a job we used electric screwdrivers and it saved a huge amount of time, plus you knew you weren't torqueing screws too tight. Thanks for the info guys. I suspected that would be the case!
|
# ? Jun 21, 2020 01:29 |
|
Don't listen to these fools, they lack imagination https://www.youtube.com/watch?v=AYYnPwcHywU E: lol wut https://www.youtube.com/watch?v=A84LYRW-63Q Hubis fucked around with this message at 02:58 on Jun 21, 2020 |
# ? Jun 21, 2020 02:53 |
|
Tim Thomas posted:as much as the flexi-click attachment scheme kind of annoys me, the offset drill and right angle drill heads for the Bosch 12v are so, so, SO useful. Holy poo poo, everyone should have a drill like this. I was actually looking at the Bosch 12v - I would be using it for taking apart some electronics quite a bit, but I'd like to get 1 tool that will do as much as possible. Do you think on the lowest torque setting it would strip medium softness screws?
|
# ? Jun 21, 2020 03:19 |
|
This one kinda reminds me of an attachment I got for doing the siding on my workshop. It connects to a drill and turns it into a set of power shears for cutting through cement fiberboard siding.
|
# ? Jun 21, 2020 04:50 |
|
TooMuchAbstraction posted:This one kinda reminds me of an attachment I got for doing the siding on my workshop. It connects to a drill and turns it into a set of power shears for cutting through cement fiberboard siding. Drill powered sheet shears are legitimate if you don't need the dedicated $600 tool
|
# ? Jun 21, 2020 09:11 |
|
cakesmith handyman posted:Drill powered sheet shears are legitimate if you don't need the dedicated $600 tool Yeah, and especially it kept dust way lower than a rotary saw would have. Was harder to cut straight with of course. I guess I'm just saying that turning a drill into a sawzall doesn't seem that outlandish. A proper sawzall of course would be better, and probably easier on the motor/batteries, but if you can only afford one power tool... Turning a drill into a table saw is uh, not great.
|
# ? Jun 21, 2020 16:24 |
|
TooMuchAbstraction posted:Yeah, and especially it kept dust way lower than a rotary saw would have. Was harder to cut straight with of course. There's also this thing: https://www.youtube.com/watch?v=gjQuewOtNOs Which I almost posted. While I wouldn't ever use or recommend it as a replacement for a proper tool, I could see it having a place in someone's tool bag if they find themselves needing to unexpectedly do a plunge cut into something like drywall for inspection or an electrical box.
|
# ? Jun 21, 2020 18:50 |
|
That in turn reminds me of spiral scrollsaw blades, which are omnidirectional. I've used 'em, they let you do tight corners like nothing else, but the cut quality is pretty terrible and they make a ton of dust.
|
# ? Jun 21, 2020 19:01 |
|
Hubis posted:Don't listen to these fools, they lack imagination First cut: kickback. Amazing.
|
# ? Jun 21, 2020 20:09 |
|
Trabant posted:First cut: kickback. Amazing. You do not use a fence for cross cuts like that because it will cause a kickback.
|
# ? Jun 21, 2020 23:19 |
|
TescoBag posted:I was actually looking at the Bosch 12v - I would be using it for taking apart some electronics quite a bit, but I'd like to get 1 tool that will do as much as possible. Do you think on the lowest torque setting it would strip medium softness screws? Why, this is literally the application I use it for. the 1 torque setting in the brushed drill slips the clutch if you look at it.
|
# ? Jun 21, 2020 23:53 |
|
JEEVES420 posted:You do not use a fence for cross cuts like that because it will cause a kickback. Oh, of course. I'm just amazed that's literally the first example of him using that... thing. Then again, bad choices were being made from the very beginning.
|
# ? Jun 22, 2020 01:08 |
|
Very late to screw-chat, but the Simpson StrongDrive Screws are loving magic. Instead of having to palm nailer in 700 god damned 16d nails, you can impact gun in 700 1.5" #10 screws. Faster, easier, less wood splitting (especially if you pre-drill for the cross-anchor screws. Also, they use a regular hex head, so a lovely little $3/ea dewalt magnetic 1/4" nut driver driver lasts roughly forever, you have no cam-out, and everything just goes in so much faster and more importantly quieter. If you ever need to put up a bunch of hangers for timber, they're by far the best thing going. Also, unlike nails you 100% cannot just flex it apart, once it's together that's it, you're gonna splinter out the wood before the strongtie or screws fail.
|
# ? Jun 22, 2020 01:27 |
|
Methylethylaldehyde posted:Very late to screw-chat, but the Simpson StrongDrive Screws are loving magic. Agreed. The 3" structural lags are also great for sistering joists/rafters, though they can get pricey fast. I mean, if I can get my framing nailer in there, I'm using that, but those SDS lags are easier than through-bolting it.
|
# ? Jun 22, 2020 02:48 |
|
Hubis posted:Don't listen to these fools, they lack imagination Those guys aren’t even trying https://www.youtube.com/watch?v=b9aW6c2w1Fk
|
# ? Jun 22, 2020 15:13 |
|
coathat posted:Those guys aren’t even trying https://www.youtube.com/watch?v=32E__mwNjAs
|
# ? Jun 22, 2020 16:04 |
|
As an older millennial, I had that 'Real Power Tool Shop', and it definitely did not have 'real power'. The separate tools isn't a 'waste' or 'marketing' thing, they just realized with automated manufacturing that a brushed 120v motor is an inexpensive part. What little can be saved by making a common motor assembly is lost when you have to add specialized couplings and brackets to make it adapt to multiple tool heads. Not to mention different gearing or motor speeds. I guess it is still used for expensive, battery-powered outdoor power tools like a weedwacker head that can convert to a pole saw or edger.
|
# ? Jun 22, 2020 18:02 |
|
B-Nasty posted:As an older millennial, I had that 'Real Power Tool Shop', and it definitely did not have 'real power'. It worked okay enough if you had fresh batteries and used the supplied balsa wood.
|
# ? Jun 22, 2020 18:17 |
|
Yeah 6AA's isn't going to give you much Powa.. My dad had a woodshop so I just used his poo poo.
|
# ? Jun 22, 2020 18:21 |
|
This looks kinda neat However, it's a kickstarter? So use a rotary encoder to measure wood length for a miter saw? That makes sense to me on paper, but I'm not sure how practical and repeatable it would actually be. Also its $100. And a kickstarter.
|
# ? Jun 23, 2020 21:42 |
|
Tres Burritos posted:This looks kinda neat Wish I had thought of this, not gonna lie
|
# ? Jun 24, 2020 02:26 |
|
I'll give it twelve months and wait till it's on AliExpress lmao Tbh that concept is loving brilliant though and I too wish I'd come up with it
|
# ? Jun 25, 2020 04:04 |
|
maybe I am just old school but I don't think I would ever fully trust that and double check with a tape measure...which would kinda negate the need for one.
|
# ? Jun 25, 2020 05:10 |
|
JEEVES420 posted:maybe I am just old school but I don't think I would ever fully trust that and double check with a tape measure...which would kinda negate the need for one. Like the old adage says, "measure exactly once with the most precision instrument available and then cut away!"
|
# ? Jun 25, 2020 05:49 |
|
Hubis posted:Like the old adage says, "measure exactly once with the most precision instrument available and then cut away!" Measure twice, cut once. Then throw that piece out since your tape measures don't agree on what an inch is and start going down a really deep rabbit hole.
|
# ? Jun 25, 2020 06:07 |
|
Measure once, then cut the piece slightly too large and slowly creep up on the final dimensions until the fit "feels" right
|
# ? Jun 25, 2020 17:58 |
|
|
# ? May 30, 2024 13:16 |
|
This is my process: Take way too long absolutely truing up your Miter Saw so it cuts exactly 45 degrees and vertical Make a new zero clearance fence so you have an completely flat surface and supported cuts for no tearout Measure 3 or 4 times Bring wood over to the saw and then realize you need to measure on the other side because your cut needs to be opposite Bring wood back and measure 3 or 4 times on the other side Bring wood back to the saw and then cut just slightly large so you can creep up on the proper fit Realize that you STILL cut the opposite miter that you were trying to cut Then you turn your 90 degree corner in to a 45 degree corner and pretend it's a feature you were going for.
|
# ? Jun 25, 2020 18:20 |