|
wesleywillis posted:Is it possible that over time the refrigerant can "leak" out of a system that doesn't actually have a real leak? Yes. The rubber hoses are called "barrier hoses", and are slightly refrigerant-permeable. 10 years is a reasonable amount of time to expect diminished performance due to low charge weight in the average passenger vehicle.
|
# ? Aug 15, 2020 19:01 |
|
|
# ? Jun 10, 2024 22:34 |
|
GOD IS BED posted:I just did this a few months ago on my brother's 09 Versa. I didn't drill any holes like the other goon did, just followed a video online (this one: https://www.youtube.com/watch?v=ol27YiguHXQ). We did have to pull the door card off, which wasn't hard. The toughest part was reaching inside the door to detach the latch and reattach it. I learned the door handles would come off if the cover over the lock (or where a lock would be if not on the driver's door) was damaged, and judging by how rare those parts were on the other Versas in the junkyard, it's a common problem. I snagged the few I could find and popped one on my bro's car. Maybe 45 minutes of work if you're completely inexperienced and less than $5 for the repair. Yeah mine was coming off even with the lock cover installed. The handle was coming off almost every time I tried opening the door so I had no choice but to do something a little more involved.
|
# ? Aug 15, 2020 19:34 |
|
Motronic posted:Yes. The rubber hoses are called "barrier hoses", and are slightly refrigerant-permeable. 10 years is a reasonable amount of time to expect diminished performance due to low charge weight in the average passenger vehicle. Is that an actual use case for the recharge kits at Wal-Mart/AutoZone or do you still need a real shop to recharge the refrigerant if you don't want to do a full DIY process like I saw in the thread about it years ago but barely remember?
|
# ? Aug 15, 2020 20:38 |
|
22 Eargesplitten posted:Is that an actual use case for the recharge kits at Wal-Mart/AutoZone or do you still need a real shop to recharge the refrigerant if you don't want to do a full DIY process like I saw in the thread about it years ago but barely remember? No recharging should be done without a proper set of manifold gauges. Those refill kits do not provide that. You are just blindly chucking in refrigerant without any real idea of whether the system is functioning properly and trying to divine how much is "enough" with only half of the normal information available.
|
# ? Aug 15, 2020 20:52 |
|
Fair enough, I'll have a shop do it.
|
# ? Aug 15, 2020 21:58 |
|
GOD IS BED posted:I just did this a few months ago on my brother's 09 Versa. I didn't drill any holes like the other goon did, just followed a video online (this one: https://www.youtube.com/watch?v=ol27YiguHXQ). We did have to pull the door card off, which wasn't hard. The toughest part was reaching inside the door to detach the latch and reattach it. I learned the door handles would come off if the cover over the lock (or where a lock would be if not on the driver's door) was damaged, and judging by how rare those parts were on the other Versas in the junkyard, it's a common problem. I snagged the few I could find and popped one on my bro's car. Maybe 45 minutes of work if you're completely inexperienced and less than $5 for the repair. That's probably exactly what it was then because the cover over the lock fell off a couple weeks ago
|
# ? Aug 16, 2020 01:08 |
|
Motronic posted:No recharging should be done without a proper set of manifold gauges. Those refill kits do not provide that. You are just blindly chucking in refrigerant without any real idea of whether the system is functioning properly and trying to divine how much is "enough" with only half of the normal information available. With those kits, would it be valid to say there's an issue with the compressor if the refrigerant level is good or is more diagnosis needed?
|
# ? Aug 16, 2020 01:24 |
|
Minto Took posted:With those kits, would it be valid to say there's an issue with the compressor if the refrigerant level is good or is more diagnosis needed? Thats the problem. You cannot tell for certain with the single gauge recharge kits, because it is only showing you suction side pressure. EDIT: also with a gauge that doesn't tell you the actual pressure.
|
# ? Aug 16, 2020 01:40 |
|
Minto Took posted:With those kits, would it be valid to say there's an issue with the compressor if the refrigerant level is good or is more diagnosis needed? You have no idea what the refrigerant level is with one of those kits. Hell, you don't even know how much is necessarily in there with a manifold gauge. You're estimating using charts based on manufacturer specs and physics.
|
# ? Aug 16, 2020 02:09 |
|
Juice that baby up, more pressure more cool
|
# ? Aug 16, 2020 02:17 |
|
so i've got a 2014 hyundai sonata and just had to replace a bulb in the headlight. This got me wondering, how hard is it to install LED lights and is that expensive?
|
# ? Aug 16, 2020 02:20 |
|
Ramadu posted:so i've got a 2014 hyundai sonata and just had to replace a bulb in the headlight. This got me wondering, how hard is it to install LED lights and is that expensive? At the moment it's not a great idea. It won't create a proper beam pattern in a halogen housing.
|
# ? Aug 16, 2020 02:33 |
|
Ramadu posted:so i've got a 2014 hyundai sonata and just had to replace a bulb in the headlight. This got me wondering, how hard is it to install LED lights and is that expensive? What lights? Headlights? If there wasn't a factory option for that it's impossible to do properly. If there was it's gonna be expensive (parts) and easy labor. Everything else? You can try replacing incandescents with LEDs but it's really not worth it in a lot of cases to to a variety of reasons in my experience.
|
# ? Aug 16, 2020 02:35 |
|
Yeah headlights. I don't know if there was a factory option for it honestly, I was given the car by my brother. I was just thinking about it when i got the new bulb.
|
# ? Aug 16, 2020 03:06 |
|
Is it dangerous to carry a bunch (5 or so) of the used little green gas propane cylinders? More so than full ones I mean? Hypothetically they'd be all used up but I don't know if some gets stuck in there a little. I know sometimes vapors are worse than liquid.
|
# ? Aug 16, 2020 06:57 |
|
Charles posted:Is it dangerous to carry a bunch (5 or so) of the used little green gas propane cylinders? More so than full ones I mean? Hypothetically they'd be all used up but I don't know if some gets stuck in there a little. I know sometimes vapors are worse than liquid. Like for hand torches? We're not even allowed to leave an "empty" one lying around at work, they're supposed to be taken to maintenence to be properly sorted. But knowing those guys they likely take them home and toss them in a bonfire.
|
# ? Aug 16, 2020 08:54 |
|
Charles posted:Is it dangerous to carry a bunch (5 or so) of the used little green gas propane cylinders? More so than full ones I mean? Hypothetically they'd be all used up but I don't know if some gets stuck in there a little. I know sometimes vapors are worse than liquid. What do you have planned for them? I take empties back to Walmart and leave them with the person that collects the big cylinders outside of garden center.
|
# ? Aug 16, 2020 12:19 |
|
Charles posted:Is it dangerous to carry a bunch (5 or so) of the used little green gas propane cylinders? More so than full ones I mean? Hypothetically they'd be all used up but I don't know if some gets stuck in there a little. I know sometimes vapors are worse than liquid. What country are you in/what cylinder style and size? Because propane isn't green in the US (that's oxygen) so I don't really know what you're talking about. If by "little" you mean small handheld disposable cylinders it's fine. If they're larger/heavier the real concern is keeping them strapped down during transport. Depending on the style it could be a pretty big deal to make sure the valve doesn't get damaged.
|
# ? Aug 16, 2020 15:27 |
|
he means the 1-lb coleman style "camping gas" cylinders. they are usually a dark green. the main danger with those is if the valve on the top is leaking, it can leak gas into your car, which is an enclosed space. those cylinders are meant to be disposable, so the valves are cheaply made.
|
# ? Aug 16, 2020 15:36 |
|
MRC48B posted:he means the 1-lb coleman style "camping gas" cylinders. they are usually a dark green. Oh those things. Yeah. Put them in a box and leave the windows down.
|
# ? Aug 16, 2020 15:57 |
|
I just make sure they're empty to the point they won't run a blowtorch anymore and then poke a hole in them with the drill. Let them air out a few minutes and they're scrap metal.
|
# ? Aug 16, 2020 18:45 |
|
OK, stupid question time. What's the most current anyone's ever seen run through a factory fuel/oil/temp gauge sender? I'm designing something I almost kind of hope to sell to people at some point, instead of just using it myself, and I don't want it catching fire if someone hooks it to a car that runs more current through the sender element than I expected, but also don't want to make the BOM 30 dollars more expensive than it needs to be by bulletproofing it. I'm guessing somewhere in the range of 100mA, but I have ZERO evidence for that and it makes me nervous.
|
# ? Aug 17, 2020 08:10 |
|
Stupid question about my '07 Corolla. I removed the rear bumper. Does this bumper foam need to be replaced? It's mostly intact, just really old and that metal bar is rusted out. What I'm more interested in are these "nubs". One has broken off. That nub is supposed to fit into this hole.
|
# ? Aug 17, 2020 17:45 |
|
melon cat posted:Stupid question about my '07 Corolla. Is the foam damaged beyond that nub (it doesn't appear to be)? My wager is that nub is just a positioning tool to make it easier to install to the impact bar and/or the bumper cover. I'd slap some two sided tape to it and call it a day. I'm probably going to regret asking, but what inspired you to take the bumper cover off?
|
# ? Aug 17, 2020 18:07 |
|
Goober Peas posted:Is the foam damaged beyond that nub (it doesn't appear to be)? My wager is that nub is just a positioning tool to make it easier to install to the impact bar and/or the bumper cover. I'd slap some two sided tape to it and call it a day. Foam isn't damaged beyond that nub. The rear quarter panel got scratched (down to the bare metal) last year and the exposed metal is starting to rust. I removed the rear bumper so I could better access the damage to do some sanding, bondo-ing, repainting to stop the rust from spreading. Wishing I did this sooner because the rust and paint chipping has spread quickly. melon cat fucked around with this message at 18:29 on Aug 17, 2020 |
# ? Aug 17, 2020 18:25 |
|
Motronic posted:The parts store. They'll even give you some else's that they've already rebuilt. Thats the problem, this is an AC compressor for an Autozam AZ-1 those parts aren't on this side of the planet.
|
# ? Aug 17, 2020 18:27 |
|
wargames posted:Thats the problem, this is an AC compressor for an Autozam AZ-1 those parts aren't on this side of the planet. Are you sure? The last time I needed an AC compressor for something weird it crossed over to a Denso unit that was being used on ag tractors in the 90s. Was able to get a rebuilt unit from a farm equipment place. Cheap. Considering this is a Japanese car, I'd be willing to bet it's a Nippon Denso unit too. See if you can find a data plate on it with a model, part or other numbers on it. I'll see if I can cross ref it for you, or at least figure out if it's going to use common parts that a rebuild shop here would even have in stock. In a tiny car like that it wouldn't surprise me to find it being the same/similar enough to the kinds of stuff on skid steers or smaller tractors. You might need to move some brackets or fittings over, but chances are good something will cross. Because, no matter how hard the parts are to come by for that car, ain't nobody designing an AC compressor specifically for one vehicle application. Motronic fucked around with this message at 18:41 on Aug 17, 2020 |
# ? Aug 17, 2020 18:39 |
|
Autozam AZ1 shouldn't have ac anyway, strip all the comfort bits
|
# ? Aug 17, 2020 18:48 |
|
Yeah get rid of those seats and get some milk crates.
|
# ? Aug 17, 2020 19:34 |
Is installing a screen a bad idea in a cooling system? Near the heater core input a plastic pipe I was replacing broke off in the hose. I think I got most of it but there could be some pieces somewhere upstream I can't get to.
|
|
# ? Aug 17, 2020 22:11 |
|
Chunjee posted:Is installing a screen a bad idea in a cooling system? Cooling system filters are absolutely a thing: https://www.jegs.com/p/Champion-Cooling-Systems/Champion-Cooling-Systems-Inline-Coolant-Filters/3629311/10002/-1
|
# ? Aug 17, 2020 22:50 |
|
taqueso posted:Autozam AZ1 shouldn't have ac anyway, strip all the comfort bits Have you been in an AZ-1 or driven one? You need AC otherwise you die from heatstroke in 10 seconds even if you have the covers for the upper glass. There is zero airflow in that thing. AZ-1 is meant to LOOK fast, it isn't actually. It also weighs as much as a couple of Costco bags of dogfood as it is.
|
# ? Aug 17, 2020 23:02 |
|
Motronic posted:Are you sure? The last time I needed an AC compressor for something weird it crossed over to a Denso unit that was being used on ag tractors in the 90s. Was able to get a rebuilt unit from a farm equipment place. Cheap. i am 100% certain as i looked for 8 months before getting this one and it failling about 2 months of florida heat.
|
# ? Aug 18, 2020 16:58 |
|
I'm looking for a new (used) car, and I've been toying with the idea of getting a manual as my daily driver. I'd like to try it out first, but I don't have any friends who own a manual. What are the chances that I regret my decision if I jump in with both feet and just buy one?
|
# ? Aug 18, 2020 18:31 |
|
Grimes posted:I'm looking for a new (used) car, and I've been toying with the idea of getting a manual as my daily driver. I'd like to try it out first, but I don't have any friends who own a manual. What are the chances that I regret my decision if I jump in with both feet and just buy one? You can learn to drive a manual relatively quickly, but if the car has an absolute poo poo clutch or something it's going to be a lot harder. So I'd recommend something with lower miles. I'd also recommend having someone who knows how to drive a manual transmission go with you to see how it feels, and they can drive it back for you and/or give you lessons. The only hard part of driving a manual transmission is going from a dead stop uphill. Otherwise it's pretty simple.
|
# ? Aug 18, 2020 18:44 |
|
Grimes posted:I'm looking for a new (used) car, and I've been toying with the idea of getting a manual as my daily driver. I'd like to try it out first, but I don't have any friends who own a manual. What are the chances that I regret my decision if I jump in with both feet and just buy one? I absolutely regretted it for the first week or two while trying to teach myself. Now, after 15 years, I absolutely regret buying a (really good) automatic and was going to buy a manual fun car on the side until, well, this year happened.
|
# ? Aug 18, 2020 18:51 |
|
Grimes posted:I'm looking for a new (used) car, and I've been toying with the idea of getting a manual as my daily driver. I'd like to try it out first, but I don't have any friends who own a manual. What are the chances that I regret my decision if I jump in with both feet and just buy one? I bought my first car as a stick GTI without having ever driven a manual car before (had ridden motorcycle) and it was fine, a little rough at the start and my dad drove it the 60 miles or so home, but after that all me and I didn't even have him teaching me as he was a dick when I stalled it on the hill of my place that first day. I jumped into the fire buying a stick living in a hilly area just fine and I regret everyday I did not hold out for a stick when I bought my current Mazda3. I also commuted in the Bay Area 45 miles each way with that stick and didn't mind it at all. TheBacon fucked around with this message at 21:28 on Aug 18, 2020 |
# ? Aug 18, 2020 19:28 |
|
I bought my 'stang as a manual without knowing how to drive one. Brought my brother who does know to bring it home, then after struggling to get it to a nearby school, I spent an hour driving circles in the school parking lot to learn. The hardest part is taking off from a stop, once you get that part down you'll be good.
|
# ? Aug 18, 2020 19:30 |
|
Grimes posted:I'm looking for a new (used) car, and I've been toying with the idea of getting a manual as my daily driver. I'd like to try it out first, but I don't have any friends who own a manual. What are the chances that I regret my decision if I jump in with both feet and just buy one? You will learn real fast. And you will be using both feet quite often. Once you learn you never forget. Just find a big empty parking lot and tool around in. The clutch isn't an off-on switch. Like was mentioned hills are fun when someone is sitting on your rear end.
|
# ? Aug 18, 2020 20:50 |
|
|
# ? Jun 10, 2024 22:34 |
|
Just make sure you watch a bunch of YouTube videos, not just on how to drive a manual, but I think it helps to watch videos on how the clutch actually works. I learned (decades ago now..) on an Integra GS-R which was very forgiving. I got the car from my Uncle at 150k and had the original clutch replaced at 160k probably because I kept hitting it unnecessarily. The biggest tip for manual is to try to get the car going with just the clutch (1-2mph) and you'll get the engagement point. Once you get used to that, everything else is easy. Except big rear end hills, but you learn to use the parking brake for that.
|
# ? Aug 18, 2020 22:30 |