|
Bob Mundon posted:Yeah came with a fence, although no resaw guide but I think I can manage. Had a pretty long drive to get it so haven't made any cuts yet but just setting it up can't really believe this thing is in my garage. Quite a step up from anything else I have. Bob, look what you gone and done. I've had a near 50 year old Milwaukee-Delta 14" for a good 20 odd years. I got it for cheap, and let it go for cheap today. I'm not a bandsaw-centric guy like some of the Woodworking guys are, but I respect the saw's versatility and sure can see how and why that can happen. So I started reading up on these, and then I too checked Craigslist, and voila, I paid forward my old saw to my son-in-law after offering him firsties on the Rikon. The casters were lovely on mine and the guy had bunged up the rollaround so one caster blew up as we were rolling it to the truck. Great guy though, he gave me a spare set of casters from his toolbox. He had a CNC laser cutter for metal (I think?) and some really cool work, and that was his forte, so he was getting out of woodworking. I like the build, the bells and whistles. And it's a tight saw.
|
# ? Sep 18, 2020 04:03 |
|
|
# ? May 31, 2024 18:43 |
|
Mr. Mambold posted:Bob, look what you gone and done. Welcome to the 324 Club! we need a with stitches
|
# ? Sep 18, 2020 04:47 |
|
powderific posted:I could be wrong but I think you might be better off just getting one with the battery built in. Both of my Milwaukee battery vacs are pretty meh, while my Dyson V8 is great and has mostly replaced the corded vacuum in our house. This drives me absolutely bananas. Vacuums (and floor polishers) are super hamstrung by simultaneously low run times and trying to wring every watt out of a non-replaceable lithium battery that kills them right quick. Meanwhile every punter with a Ryobi drill/driver has 2 or 3 decent quality 18V 3Ah batteries sitting on the bench for weekend duty. When your Dyson (or Karcher) custom battery wears out then you have to pay a few hundred for a new one. In the meantime you have to wait 2-3 hours for the crappy wall wart to recharge.
|
# ? Sep 18, 2020 13:48 |
|
To the Rikon 324 gang I'm seeing some pictures of fences that have a plastic nub on the far end that keeps the fence from rubbing on the table top. Mine doesn't but being used it might have been taken off, does everyone else have the on their fence?
|
# ? Sep 18, 2020 14:13 |
|
~Coxy posted:When your Dyson (or Karcher) custom battery wears out then you have to pay a few hundred for a new one. Not disagreeing about wanting better tool brand vacuums, but for the V8 at least it’s like 3 screws and the pack is $130 from Dyson or you can just get a knockoff for like $50.
|
# ? Sep 18, 2020 14:19 |
|
Bob Mundon posted:To the Rikon 324 gang I'm seeing some pictures of fences that have a plastic nub on the far end that keeps the fence from rubbing on the table top. Mine doesn't but being used it might have been taken off, does everyone else have the on their fence? Mine didn't come with one. Aluminum fence sits right the table but with the tubular fence guide you just pivot it up off the table to move it.
|
# ? Sep 18, 2020 14:34 |
|
Who saw this one coming.Autodesk posted:Important changes are coming to your Fusion 360 for personal use software that you need to know about.
|
# ? Sep 18, 2020 15:29 |
|
Jaded Burnout posted:Who saw this one coming. Does the software update automatically? Can you keep the old functionality by keeping the old version? I don't own a CNC machine, but that list of features sounds like you've basically lost all functionality from the software with this "update".
|
# ? Sep 18, 2020 16:10 |
|
Rutibex posted:Does the software update automatically? Can you keep the old functionality by keeping the old version? I don't own a CNC machine, but that list of features sounds like you've basically lost all functionality from the software with this "update". Yes, no. It's very tightly hooked into their cloud, I suspect you would need to go to great lengths to try and run it without it phoning home for an update.
|
# ? Sep 18, 2020 16:38 |
|
You can't even work on local files. You can export and presumably import, but your working files are stored in their cloud storage, no exceptions.
|
# ? Sep 18, 2020 16:46 |
|
Jaded Burnout posted:You can't even work on local files. You can export and presumably import, but your working files are stored in their cloud storage, no exceptions. You can't export anything unless you save it to their cloud first. They have been saying they were going to lock it all down for over a year. SaaS is all about giving you a taste so you get used to their software then switch it to paid so you are so ingrained in using it you will just pay the monthly fees.
|
# ? Sep 18, 2020 18:15 |
|
JEEVES420 posted:They have been saying they were going to lock it all down for over a year. They haven't been saying it in a way that I saw, given I've got an account and actively use the app. JEEVES420 posted:SaaS is all about giving you a taste so you get used to their software then switch it to paid so you are so ingrained in using it you will just pay the monthly fees. Some of it is. Some of it is about providing a decent free service and then providing paid addons and upgrades. Bait and switch is usually not the way it goes with decent companies.
|
# ? Sep 18, 2020 18:25 |
|
Hmmm will I still be able to export stl for 3d printing? That's really all I use it for.
|
# ? Sep 18, 2020 19:43 |
|
Presumably. What I pasted was the entirety of the email.
|
# ? Sep 18, 2020 19:50 |
|
I’m looking at getting a rail saw for cutting some plywood to make a run of cabinets. I used a festool one today at woodcraft, shockingly it was wonderful to use. I don’t want to spend festool money though, so I was looking at Kreg. I was wondering if the system that uses your own circular saw (which is about 70 or so) is worth getting, or should I look at their version that comes with its own saw? ($400) I have a corded ryobi circular saw that cuts fine. Thoughts?
|
# ? Sep 19, 2020 23:29 |
|
AFewBricksShy posted:I’m looking at getting a rail saw for cutting some plywood to make a run of cabinets. It works well, keep the bottom clean and the rubber sticks pretty decent. Just don't trust that it squares up by laying it down with the lip. I used to draw a line but now I just do 4 dashes and line up the guide. Pretty quick to setup once you figure out kerf/blade placement. The plastic edge on the guide is meant to be cut off on the first cut so you know exactly where the blade falls on that side. The same plate that attaches to the saw can be used on the track and the edge guide which is nice. Cutting a bunch of sides for cabinets at 16" was a breeze with the edge guide since I don't have a slider on my table saw. Only real draw backs are no plunge cutting (at least I haven't tried), since it doesn't lock into the rail, and if it gets sawdust under it it will slip.
|
# ? Sep 20, 2020 00:02 |
|
the bosch one works well. the rails are expensive.
|
# ? Sep 20, 2020 00:03 |
|
How does one remove a morse 2 taper jacob's chuck from a drill press? When I've seen people using lathes or mills they're able to apply pressure from the back, but that's seemingly not an option with my drill press.
|
# ? Sep 20, 2020 17:17 |
|
Jaded Burnout posted:How does one remove a morse 2 taper jacob's chuck from a drill press? When I've seen people using lathes or mills they're able to apply pressure from the back, but that's seemingly not an option with my drill press. Have you tried ?
|
# ? Sep 20, 2020 19:13 |
|
Mr. Mambold posted:Have you tried Is that not the answer to every question asked in this forum? I've even read the manual, but I think the assumption is that lowly consumers never would, so I'm looking for ideas from someone with experience rather than a listicle.
|
# ? Sep 20, 2020 19:24 |
|
Jaded Burnout posted:How does one remove a morse 2 taper jacob's chuck from a drill press? When I've seen people using lathes or mills they're able to apply pressure from the back, but that's seemingly not an option with my drill press. Looking at/posting the exploded parts diagram may help? An invariable follow up question is going to be 'why are you taking it off?'
|
# ? Sep 20, 2020 19:56 |
|
Kaiser Schnitzel posted:Sometimes you can drive it out from the other end of the shaft if the shaft is hollow. It's not this, but it might be one of the others, I'll take a look, thanks Kaiser Schnitzel posted:Looking at/posting the exploded parts diagram may help? There isn't one Kaiser Schnitzel posted:An invariable follow up question is going to be 'why are you taking it off?' It's got some runout so I think I didn't fit it quite right.
|
# ? Sep 20, 2020 20:03 |
|
Jaded Burnout posted:Is that not the answer to every question asked in this forum? Is there any space between the chuck and, ah not the spindle, but what it inserts into...the head? Where you could get an open end wrench (spanner?) in between and smack down with a deadblow hammer is what I'm thinking. Give us a closeup pic, M8. Mr. Mambold fucked around with this message at 20:23 on Sep 20, 2020 |
# ? Sep 20, 2020 20:21 |
|
Jaded Burnout posted:It's not this, but it might be one of the others, I'll take a look, thanks I've got one that there is no way to drive it out from the other side nor was there a good way to get something over it to bang it down without damaging the chuck like Mr. Manbold is suggesting - might work for you if the check is trashed anyway. In any case, I use a slide hammer tightened into the chuck to pull it. Takes a few good whacks but it comes out.
|
# ? Sep 20, 2020 20:38 |
|
Mr. Mambold posted:Is there any space between the chuck and, ah not the spindle, but what it inserts into...the head? Where you could get an open end wrench (spanner?) in between and smack down with a deadblow hammer is what I'm thinking. The quill, yeah. There's a lil bit of space, I'll take photos. Motronic posted:I've got one that there is no way to drive it out from the other side nor was there a good way to get something over it to bang it down without damaging the chuck like Mr. Manbold is suggesting - might work for you if the check is trashed anyway. TIL about a new tool! Thanks!
|
# ? Sep 20, 2020 20:44 |
|
Jaded Burnout posted:
Just make sure to use it right https://i.imgur.com/eL2Cx3l.mp4
|
# ? Sep 20, 2020 22:06 |
|
Wow this is really stupid.
|
# ? Sep 21, 2020 00:34 |
|
Any suggestions for a simple dust cyclone for a shop vac? Tried the dustopper from Home Depot and I'm sure it's work great for dust, but plane shavings get clogged and everything bypasses the cyclone. Thinking about trying the dust deputy but it seems expensive for what it is. Don't need anything crazy, just something that runs off a shop vac that can handle some dust and shavings.
|
# ? Sep 22, 2020 04:30 |
|
Bob Mundon posted:Any suggestions for a simple dust cyclone for a shop vac? Tried the dustopper from Home Depot and I'm sure it's work great for dust, but plane shavings get clogged and everything bypasses the cyclone. Thinking about trying the dust deputy but it seems expensive for what it is. Don't need anything crazy, just something that runs off a shop vac that can handle some dust and shavings. The dust deputy works incredibly well. I hemmed and hawed about spending the money, and wished I would have bought it sooner. It works incredibly well. There’s also plenty of overseas knockoffs if you aren’t in a rush and want to save money.
|
# ? Sep 22, 2020 05:34 |
|
I. M. Gei posted:I don’t have a ton of cash to work with, so I can only really afford the 2.0 Ah battery that comes with the sprayer. I could afford to grab another battery if I was buying a smaller sprayer, but the 4-gallon Ryobi is the only battery sprayer my local Home Depot has in stock that comes with a battery and is within my price range. I’d prefer not to have to wait on shipping for something smaller, since I can’t really put off spraying my trees any longer than I already have. So dude, have you put that sprayer to the test? I wanted to go with the 1 gallon sprayer since I've got tomatoes, shrubs, but only got 6 fruit trees, but 2 of them are pretty massive. Plus that 4 gallon rig looks like a back bender, and I've already got that issue. I looked at the Ryobi single gallon and passed on it for the SunJoe, breaking the ryobi ecosphere. Sun Joe supposedly has 72 psi factor, more than the 1 gallon Ryobi. Used it once. It's a piddler. It's fine for the tomatoes and shrubs, but I can't see spraying my pear trees multiple times. So I returned it and got the Ryobi you've been speccing, after viewing some ryobi dude's youtube. I'm walking to the checkout in Home Depot and there's a guy ahead of me with the same Ryobi sprayer in a cart, so I'm gonna holler at him to get his opinion. He breezed through an unattended checkout and kept trucking. Must have been a secret goon shopper. Also, I think you're totally on point with just using the 2 amp battery, these things seem to be pretty efficient.
|
# ? Sep 22, 2020 17:17 |
|
Hello tools! (and I mean that in the gentlest way possible) DIY Secret Santa signups are open! https://forums.somethingawful.com/showthread.php?threadid=3941260
|
# ? Sep 22, 2020 19:20 |
|
corgski posted:Hello tools! (and I mean that in the gentlest way possible) DIY Secret Santa signups are open! I’m getting real strong deja vu vibes here... I really need to start reading other subforums New bandsaw time... Super tempted to buy the Grizzly 17” anniversary edition: https://www.grizzly.com/products/Grizzly-17-2-HP-Bandsaw-35th-Anniversary-Edition/G0513ANV Yay or nay? Catatron Prime fucked around with this message at 06:24 on Sep 23, 2020 |
# ? Sep 23, 2020 00:49 |
|
OSU_Matthew posted:https://www.grizzly.com/products/Grizzly-17-2-HP-Bandsaw-35th-Anniversary-Edition/G0513ANV Do it
|
# ? Sep 23, 2020 01:09 |
|
Bob Mundon posted:Any suggestions for a simple dust cyclone for a shop vac? Tried the dustopper from Home Depot and I'm sure it's work great for dust, but plane shavings get clogged and everything bypasses the cyclone. Thinking about trying the dust deputy but it seems expensive for what it is. Don't need anything crazy, just something that runs off a shop vac that can handle some dust and shavings. For planer shavings something like this on a trashcan would work https://www.woodcraft.com/products/trash-can-cyclone-lid
|
# ? Sep 23, 2020 03:34 |
|
Bob Mundon posted:Any suggestions for a simple dust cyclone for a shop vac? I have a Clearvue Mini CV06. It's an expensive option but the novelty of watching the cyclone through the clear plastic is worth the extra $20. Comatoast fucked around with this message at 19:42 on Sep 23, 2020 |
# ? Sep 23, 2020 19:37 |
|
Sure, I'll order a makita track saw new. What a treat! Instead, what I got, was a very used saw in beat up Christmas-wrapping-paper-torn box, with a burned up blade. Im keeping the batteries. Go gently caress yourself, Amazon.
|
# ? Sep 24, 2020 02:17 |
|
Cannon_Fodder posted:Sure, I'll order a makita track saw new. What a treat! Now the next person amazon pawns it off on is going to get an even shittier saw with no batteries
|
# ? Sep 24, 2020 02:20 |
|
Not exactly a tool, but does anyone have recommendations for a generator? Situation is I live in a semi-rural area with a well for my water and an insulin-dependent family member, so any power loss of 12 hours or more will start to create issues. Have lived in this house for 5 years and have never had power go out for more than a few hours, but its 2020 and winter is coming so... I want to be able to run my fridge, my well pump, and maybe my furnace blower (though I have a wood stove and lots of wood). Wish I had the cash for a full house backup, but those are $texas, so I'm looking at an inverter gas generator in the 3-4kw range. Any brands to avoid? Any hidden gems?
|
# ? Sep 24, 2020 14:35 |
|
I'd say get a propane generator if you can swing it. Way quieter, fuel can last in storage indefinitely, no carburator to gently caress up on you.
|
# ? Sep 24, 2020 14:40 |
|
|
# ? May 31, 2024 18:43 |
|
Yeah, thought about that, but the downsides are that is theres not two cars full of propane in my driveway i can get fuel from if needed, and not a few thousand gallons of propane at the gas station a mile away. But, are dual fuel ones worth it, or are they a compromise that loses the best of both?
|
# ? Sep 24, 2020 15:10 |