|
FISHMANPET posted:Get starbit screws and just get whatever seems reasonably priced, I'm not sure brand of bit is something you need to obsess over for the scale of projects around the house. Bits are consumables. People who have problems with bits don't realize that. Buy a whole pack of the ones you need for a project and pitch them as soon as they start camming out/show the least bit of damage.
|
# ? Oct 14, 2021 23:26 |
|
|
# ? May 29, 2024 02:24 |
|
Motronic posted:Bits are consumables. People who have problems with bits don't realize that. Buy a whole pack of the ones you need for a project and pitch them as soon as they start camming out/show the least bit of damage. On top of that, I found that I just stopped damaging bits at all when I switched over to square and Torx bits for everything I build myself. I'm not worried about longevity but it just happens.
|
# ? Oct 14, 2021 23:29 |
|
tracecomplete posted:On top of that, I found that I just stopped damaging bits at all when I switched over to square and Torx bits for everything I build myself. I'm not worried about longevity but it just happens. I dont do tons of stuff with screwdriver bits but yeah, with square drive stuff, which I know some of you think is the devil, I don't have a lot of problems with cam out, and I find square in particular, is very forgiving of a bit thats been a bit damaged unless its pretty much cheese grade metal.
|
# ? Oct 14, 2021 23:34 |
|
I tend to buy 1lb boxes of screws so I don't need storage for a million larger boxes, and every box comes with a bit. I can't spin around and throw a rock without hitting a star drive bit.
|
# ? Oct 14, 2021 23:40 |
|
tracecomplete posted:On top of that, I found that I just stopped damaging bits at all when I switched over to square and Torx bits for everything I build myself. I'm not worried about longevity but it just happens. Yeah, I love the star head coated deck screws for things I just need to bash together. Bu basically anything other than phillips bits will last a pretty long time. Phillips bits are literally sold in contractor packs of like 20+ for a reason. They are poo poo, and no amount of quality of metal can fix the bad engineering that is phillips. The only redeeming use/quality of phillips is for drywall when you're using a dimple bit. Because that's about the only time you really need something to cam out and they are perfect at that. The rest of this is from a time when slip clutches on driving tools didn't exist and torque drivers were too expensive and/or nonexistant.
|
# ? Oct 14, 2021 23:46 |
|
FISHMANPET posted:Get starbit screws and just get whatever seems reasonably priced, I'm not sure brand of bit is something you need to obsess over for the scale of projects around the house. Awesome, thanks all.
|
# ? Oct 14, 2021 23:47 |
|
wesleywillis posted:with square drive stuff, which I know some of you think is the devil Square drive is the best drive. I sleep with a McFeely's catalogue under my pillow every night.
|
# ? Oct 15, 2021 01:12 |
|
I think it's my own bad habits but I always end up rounding out square bits super fast. The torx seems to be the best bang for the buck as far as time/driven screws. I also don't ever seem to gently caress up torx bits for some reason. Like, I know they're disposable but I have some that have drilled like thousands of screws and still work great.
|
# ? Oct 15, 2021 01:23 |
|
Motronic posted:The only redeeming use/quality of phillips is for drywall when you're using a dimple bit. Because that's about the only time you really need something to cam out and they are perfect at that. This is a profound truth, one that has somehow filled a void in my existence, perhaps equivalent to the volume of metal in phillips bits and screw heads that I've stripped out within that duration.
|
# ? Oct 15, 2021 02:07 |
|
I have a coworker whose job title is "mechanical engineer" and he told me that Philips heads are designed to cam out and strip as a feature to protect against over torquing the screws. He told me this after I asked him what idiot was going around stripping every screw in the office. I yelled at him how wrong he was but I don't think it got through.
|
# ? Oct 15, 2021 02:56 |
|
oXDemosthenesXo posted:I have a coworker whose job title is "mechanical engineer" and he told me that Philips heads are designed to cam out and strip as a feature to protect against over torquing the screws. He told me this after I asked him what idiot was going around stripping every screw in the office. I yelled at him how wrong he was but I don't think it got through. I've heard that before too, and it makes sense in context of 100 years ago if you're having guys without torque wrenches assemble cars on an assembly line. Someone who wrote a whole book about screws and screwdrivers agrees. https://www.roadandtrack.com/car-culture/car-accessories/a33490602/phillips-head-screwdriver-history/
|
# ? Oct 15, 2021 03:13 |
|
canyoneer posted:I've heard that before too, and it makes sense in context of 100 years ago if you're having guys without torque wrenches assemble cars on an assembly line. In an environment where you're driving and tightening millions of identical screws and bolts, into controlled materials, and without torque control, I guess that makes sense. In the modern world for miscellaneous use it's abject trash. I've also head contradictory claims on the purpose of the cam out effect. Wikipedia claims that there's no direct evidence that torque control was the original purpose. I've read elsewhere that its purpose is to protect the screwdriver from damage because the screw fails first. Whatever the reason I hate them and my coworker is an idiot who destroys most tools he uses.
|
# ? Oct 15, 2021 03:40 |
|
canyoneer posted:Tools: a whole book about screws and screwdrivers
|
# ? Oct 15, 2021 03:44 |
|
CPO has a bunch of factory refurb Bosch angle grinders right now. I bought this one recently. I haven't gotten a chance to use it yet but it spins and feels pretty solid for being so inexpensive. Planning to get one of those Kutzall wheels and mess around with some power carving. https://www.cpooutlets.com/factory-reconditioned-bosch-1375a-46-4-1-2-in.--6-amp-small-angle-grinder/bshr1375a-46.html
|
# ? Oct 15, 2021 04:33 |
|
I have one and it is solid for the rare occasion I have need for an angle grinder.
|
# ? Oct 15, 2021 04:40 |
|
How's everyone's luck with the factory reconditioned tools? I'm tempted but suspicious
|
# ? Oct 15, 2021 04:47 |
|
Vim Fuego posted:How's everyone's luck with the factory reconditioned tools? I'm tempted but suspicious
|
# ? Oct 15, 2021 04:55 |
|
heffray posted:Ryobi or Ridgid stuff from https://www.directtoolsoutlet.com/ has been fine for me (18V brushless circ saw, Ridgid thickness planer, etc). Same. I've bought some recon Ryobi batteries as well for $20 a pop, haven't noticed a difference other than they've got the word RECON melted into the casing. I assume they replaced the 18650s.
|
# ? Oct 15, 2021 05:05 |
|
I went with the two-pack of Mastercraft angle grinders.
|
# ? Oct 15, 2021 05:21 |
|
Has anyone tried the knock off hitachi framing nailers? I’m looking at either the Airlocker or the Pneutool. Waiting to find a nice vintage NR83 but would like to get a cheap new one for work or when other people are gonna use it. Paslode is all anyone uses here and I’m not a fan. Haven’t been reliable (although nobody seems to maintain them either) and there’s a fair amount of plastic on them.
|
# ? Oct 15, 2021 11:38 |
|
Vim Fuego posted:How's everyone's luck with the factory reconditioned tools? I'm tempted but suspicious Great, I never buy new unless I’m in a time crunch and can’t afford to wait. Factory reconditioned come w a warranty and return policy in my experience, and used tools can be visually inspected for abuse.
|
# ? Oct 15, 2021 11:42 |
Literally A Ghost posted:I think it's my own bad habits but I always end up rounding out square bits super fast. The torx seems to be the best bang for the buck as far as time/driven screws. I also don't ever seem to gently caress up torx bits for some reason. Like, I know they're disposable but I have some that have drilled like thousands of screws and still work great. Same for me on square bits. Better than phillips ofc but not near as good as torx
|
|
# ? Oct 15, 2021 13:43 |
|
I just hate square screws because my PO used 50% square, then a random assortment of Phillips, flat, and hex screws, literally all over the house
|
# ? Oct 15, 2021 14:09 |
|
rockear posted:CPO has a bunch of factory refurb Bosch angle grinders right now. I bought this one recently. I haven't gotten a chance to use it yet but it spins and feels pretty solid for being so inexpensive. Planning to get one of those Kutzall wheels and mess around with some power carving. Do you post your work anywhere? Great share, is this the same on off switch as their 5 inch? I do a ton of power carving, too! Just picked up another holy galahad king Arthur attachment, they are amazing with the see through holes. I also use metal use grinding pads to great success on wood. Die grinder kutzall burrs whip rear end, too. Chainsaw rough out to save yourself time and not make dust of everything Also wear a mask and eye pro obviously, dust everywhere Vim Fuego posted:How's everyone's luck with the factory reconditioned tools? I'm tempted but suspicious All of my reconditioned makita tools have been super solid and half off Harry Potter on Ice fucked around with this message at 15:57 on Oct 15, 2021 |
# ? Oct 15, 2021 15:40 |
|
Vim Fuego posted:How's everyone's luck with the factory reconditioned tools? I'm tempted but suspicious Most of my 20v max dewalts are factory refurbs I've picked up as bare tools off of ebay. Been going great.
|
# ? Oct 15, 2021 15:49 |
|
Johnny Truant posted:I just hate square screws because my PO used 50% square, then a random assortment of Phillips, flat, and hex screws, literally all over the house I may be this future PO. I prefer torx but most things come with phillips so I use those too occasionally, but I also out of convenience often find myself grabbing Kreg pocket hole screws whenever a panhead will work for something. My around the house drill has a bit attachment with R2, T25, flat, and PH2 on it at all times. From my desk I can spot square drive, torx, phillips, and flathead screws(wall plates) in use around the room!
|
# ? Oct 15, 2021 15:51 |
|
I just use the Menards brand construction or triple-coated deck screw (which are all T25, except the short ones which are Phillips) and then I've got a random assortment of small Spax screws (that are all Phillps) which I use for small things or to replace cheap little screws that might come with stuff I buy. Realistcally speaking I don't know it's possible to make much of a specific choice of drive head, when the manufacturers make that decision, and stores only carry one head type for a specific size and screw type.
|
# ? Oct 15, 2021 15:58 |
|
Vim Fuego posted:How's everyone's luck with the factory reconditioned tools? I'm tempted but suspicious I made a career of it back before Rockwell sold off to Porter Cable and I needed to rebuild my power tool set (that was around 1980) and never looked back. I still have a working rockwell sawzall, a router I set up for doors, and the door jig from then- although tbf, I've hardly used them the past 15 years. Reconditioning to me means (or should) mean they've been QC'd for actual defects and fixed instead of just boxed up new.
|
# ? Oct 15, 2021 16:49 |
|
Harry Potter on Ice posted:Do you post your work anywhere? Great share, is this the same on off switch as their 5 inch? I do a ton of power carving, too! Thanks for the tips! I haven't tried it at all yet as I haven't bought a wheel for it. Would love to see some of your stuff if it's easily shareable. I actually bought the grinder because it was cheap and seemed like it would come in handy at work (I'm a roofer). Then it occurred to me that we throw away a lot of wood because there's 6" of dry rot at one end of a 16' board and I could start taking it home and make art or furniture out of it. My first project will probably be Stumpy Nubs's workbench because I don't have a good place to work. I'm not sure about the switch. I'm pretty sure it's latching but I don't have it handy to verify.
|
# ? Oct 15, 2021 17:55 |
|
FISHMANPET posted:I'm picking up my Blue HF top chest today that I ordered 4 weeks ago, same. Update: obviously I measured beforehand to make sure it would fit, and I saw it on display in the store, but still kind of in awe about how huge this thing actually is. It's a bit too heavy for me to move on my own (and my wife was not in the mood for the heavy labor of hefting it out of my car and into the basement). So I had to sort of slide it out the back of my hatchback and rest it on some sawhorses, ripped off the box, and pulled all the drawers out. Then I was able to very carefully heft it myself into the house, and then brought all the drawers in and put them back, and started loading it up. Discovered that my tabletop isn't perfectly flat either, so the chest currently rocks a bit (or the chest itself isn't square on the bottom...). As for the chest itself, it's great. It's got that paint job on all sides, including the bottom, so it's actually kind of "slippery" and can easily slide across my MDF tabletop there. There are two holes in the bottom (maybe for mounting to the bottom chest) that I will probably end up using to bolt it down to the table, so it doesn't move anymore. At the very least, some kind of grippy rubber feet would be useful to give it some friction.
|
# ? Oct 15, 2021 18:36 |
|
I have the rolly one and overall the HF chests are pretty decent for joseph homeowner
|
# ? Oct 15, 2021 18:44 |
|
I have 2 of the 4 drawer carts with the flip up lid. One outside in the carport for car stuff and another in the kitchen to make up for lack of storage.
|
# ? Oct 15, 2021 18:57 |
|
Thumposaurus posted:I have 2 of the 4 drawer carts with the flip up lid. I see the white 5-drawer carts in hospitals regularly. It's amusing, they take the US General plate off, but they're so distinctive.
|
# ? Oct 15, 2021 20:11 |
|
There are so many common tools used in hospitals it's wild I just finished an autopsy and we used a pair of Grainger needle nosed pliers, the common blue/yellow vice grips, scotch Brite pads, and regular ziplock sandwich bags
|
# ? Oct 15, 2021 21:41 |
|
Johnny Truant posted:There are so many common tools used in hospitals it's wild My wife tells me that oscillating saws are very often used in the OR.
|
# ? Oct 15, 2021 22:41 |
|
I’ve heard a story of an open heart surgeon a (long) while back who used craftsman bits for some piece of work; after so many times through the autoclave they got all jacked up so they swapped them out under warranty.
|
# ? Oct 15, 2021 22:55 |
|
Historically there were loads of problems with orthopedic surgeons using whatever tools for screwing in implants, it totally fucks patients up because any tiny shavings of screwdriver up against the screw lead to galvanic corrosion and a big risk of implant failure. Implant kits come with tools made out of the same material to avoid that happening. Surgeons really shouldn't be using their HF kit, maybe it happens but seems unlikely in 2021.
|
# ? Oct 15, 2021 23:13 |
|
knox_harrington posted:Historically there were loads of problems with orthopedic surgeons using whatever tools for screwing in implants, it totally fucks patients up because any tiny shavings of screwdriver up against the screw lead to galvanic corrosion and a big risk of implant failure. Implant kits come with tools made out of the same material to avoid that happening. Surgeons really shouldn't be using their HF kit, maybe it happens but seems unlikely in 2021. yah using conventional stuff is big no no, surgical tools are purpose designed. Plus they’re all tracked and registered so if there’s problem it’ll trigger further investigations etc Autopsies are different, I would assume the tools are disposed of instead of sterilized & autoclaved but after seeing how hospitals handled PPE w COVID, I’m guessing they re-use them Part of the reason orthopods make so much is from royalties they collect from the medical hardware they invent (and then use exclusively, collecting licensing fees from their own surgeries on top of usual compensation)
|
# ? Oct 15, 2021 23:38 |
|
lil poopendorfer posted:Autopsies are different, I would assume the tools are disposed of instead of sterilized & autoclaved but after seeing how hospitals handled PPE w COVID, I’m guessing they re-use them nah you have a lot of reusable tools. orange pruning shears, for example. dunno if those're Caftsman!
|
# ? Oct 15, 2021 23:41 |
|
|
# ? May 29, 2024 02:24 |
|
I want to fit a vise to my workbench. However, while 3 of the 4 mounting holes are fine, the fourth is mostly above one of the bench legs. If I move it further across to clear the leg, then the jaws won't clear the benchtop if I have a workpiece in them. Any suggestions on how to mount this? I could put a big screw into that last hole and bolt the other three through, or mount the vice to a steel plate somehow that is then itself bolted into the bench further out? I want to be able to use the vise from either edge of the corner, so it really needs to be in this location. I mean, maybe that's not too big a deal, but I'd hate to miss out on that extra bit of versatility if I can avoid it.
|
# ? Oct 16, 2021 00:15 |