|
It depends.
|
# ? Nov 26, 2022 23:28 |
|
|
# ? May 29, 2024 18:50 |
|
Bob Mundon posted:Noted, good to hear. Is it handy to have both standard & metric, or should I be better off going with this one? If you're working on anything around the house from cars to appliances to lawn equipment I'd say it is pretty necessary to have both. Depends on what you need.
|
# ? Nov 27, 2022 00:16 |
|
One thing to keep in mind about the cheapy tap and die sets is the wrench is going to be extra garbage.
|
# ? Nov 27, 2022 00:31 |
|
I'm looking to pick up a standard bench vise - anybody have thoughts on Harbor Freight's Central Forge swivel vise line? They've got a 5" on for $60, while almost everything used I find on craigslist is a janky piece of rusted poo poo people want more than brand new prices for. Idgi
|
# ? Nov 27, 2022 17:12 |
|
Johnny Truant posted:I'm looking to pick up a standard bench vise - anybody have thoughts on Harbor Freight's Central Forge swivel vise line? Vintage vises are a thing. I have a cheapo Irwin vise from amazon and it's fine, and I've heard that the HF ones are fine, but my upgrade to a proper wooden leg vise was a gamechanger.
|
# ? Nov 27, 2022 17:17 |
|
Bench Grinder question: What type of wheel should I use to grind stainless steel and keep a decent finish on? I'm looking at grinding down some Swiss Army Knife parts to a different profile. My grinder is an ancient 6"x3/4"x1/2" one I got for free but seems to be in working order. I am thinking the wheel from this combo would be fine? https://www.amazon.com/Grinder-Grin...04&sr=8-19&th=1 SpartanIvy fucked around with this message at 18:12 on Nov 27, 2022 |
# ? Nov 27, 2022 18:08 |
|
Johnny Truant posted:I'm looking to pick up a standard bench vise - anybody have thoughts on Harbor Freight's Central Forge swivel vise line? I think the central forge vice did alright on Project Farm's comparison from a few weeks ago https://www.youtube.com/watch?v=PFDOGoMXHNk if you don't want to see the tests he has the results toward the end of the video where he shows everything compared in bar charts and such.
|
# ? Nov 27, 2022 18:11 |
|
I broke a hf vice once. It took putting an 8' pipe on the handle and cranking on a comealong attached to the end. The handle and screw were fine the piece that travels inside snapped from the pressure.
|
# ? Nov 27, 2022 19:05 |
|
CommonShore posted:Vintage vises are a thing. Lol I can definitely see that but it's literally every fuckin vise within 100 miles is "5" vise, 3 years old, a little love but I know what I have no low-balls!" and it's this absolute piece of poo poo, visible pieces falling off, priced more than a brand new one of the same brand Squibbles posted:I think the central forge vice did alright on Project Farm's comparison from a few weeks ago Tight, thank you! Guyver posted:I broke a hf vice once. It took putting an 8' pipe on the handle and cranking on a comealong attached to the end. The handle and screw were fine the piece that travels inside snapped from the pressure. Lol I doubt I'd be using it for anything that intense so this sounds like a positive point
|
# ? Nov 27, 2022 19:28 |
|
Is it a bad idea/unsafe to buy one of those plastic “universal” router base plates, attach my Dewalt router to that, and then mount that under an aluminum table plate? I have a DWP611 and I got a Rockler table with a basically undrilled plate (three total holes, 4 inches apart) off Marketplace. If there’s a cheap, safe way to make this work (aka not “buy another router”), that’d be ideal. I don’t have a drill press, so I’m not sure if I could drill new holes accurately. I know the router isn’t designed for table usage, but I’m very much at the beginning of this journey and truly don’t need more than what it provides.
|
# ? Nov 27, 2022 20:01 |
|
Johnny Truant posted:I'm looking to pick up a standard bench vise - anybody have thoughts on Harbor Freight's Central Forge swivel vise line? a big hunk of cast iron in an approximately useful shape has always been where Harbor Freight really shines.
|
# ? Nov 28, 2022 01:13 |
|
Anyone have opinions on the different car jacks at harbor freight or otherwise? Used my friend's this past weekend: https://www.harborfreight.com/autom...blue-56641.html But thinking of getting an aluminum one because they're awkward things: https://www.harborfreight.com/automotive/jacks-jack-stands/floor-jacks/2-ton-aluminum-racing-floor-jack-with-rapid-pump-64542.html 2 ton is plenty for my 2600lb car.
|
# ? Nov 28, 2022 18:51 |
|
Super cool video showing how they used radial arm saws in a production manner during WWII: https://www.youtube.com/watch?v=HiGH0Qsu3ak&t=886s I love the clever jig they show at ~6:30 to gang cut the stringers.
|
# ? Nov 28, 2022 19:31 |
Russian Bear posted:Anyone have opinions on the different car jacks at harbor freight or otherwise? I have the 2nd linked Aluminum jack because I drive a small Prius and the jack was very cheap. Pros: cheap, light, easy to use, functions smoothly and doesn't feel flimsy or wobbly. Cons: The total lift height is a big problem if you are lifting anywhere except the body points behind the front wheel / in front of the rear wheel. For example trying to jack up the prius on the jack point under the engine compartment it will not lift the vehicle high enough to get even the small HF jack stands underneath it and I have to use a massive wooden block as a spacer (not really comfortable using that tbh). Likewise using it to lift a higher clearance vehicle (2018 RAV4) it will not lift the rear axle high enough to put a small HF jackstand underneath either, unless you use a block / spacer. If I had to do it all over again, I'd just buy the larger jack with the greater lift height even if it was more expensive, ymmv.
|
|
# ? Nov 28, 2022 19:49 |
|
Russian Bear posted:Anyone have opinions on the different car jacks at harbor freight or otherwise? project farm did a review on floor jacks just a couple months ago: https://www.youtube.com/watch?v=g5_64r2PR7A tldr: all the harbor freight jacks did very well, but it's worth watching to get a better idea of the differenecs between them
|
# ? Nov 28, 2022 19:58 |
|
BIG-DICK-BUTT-gently caress posted:project farm did a review on floor jacks just a couple months ago: Just watch out for their transmission jacks apparently https://www.youtube.com/watch?v=djNqJGDWSSw
|
# ? Nov 28, 2022 20:13 |
|
And don't use their jack stands. No matter how many times they recall them.
|
# ? Nov 28, 2022 20:32 |
H110Hawk posted:And don't use their jack stands. No matter how many times they recall them. Who do you like for Jack stands?
|
|
# ? Nov 28, 2022 20:43 |
|
That Works posted:Who do you like for Jack stands? I believe ESCO stands are the Goon Approved™ jack stands.
|
# ? Nov 28, 2022 20:59 |
|
BIG-DICK-BUTT-gently caress posted:Super cool video showing how they used radial arm saws in a production manner during WWII: Very cool. 22" blades, no guards, long sleeves, everyone hatted... the 40s were wacky.
|
# ? Nov 28, 2022 21:00 |
|
BIG-DICK-BUTT-gently caress posted:Super cool video showing how they used radial arm saws in a production manner during WWII: My favorite part is the very beginning, talking about how table saws were old-fashioned and you spent so much time setting up for the next cut. And now 60-80 years later we decided that maybe the safety benefits of the table saw were worth the extra time spent in setup. Then again that table saw they were showing looked pretty basic, possibly even handmade, I wonder what DeWalt and Stanley and others were making in the realm of big-rear end industrial table saws in the 40s.
|
# ? Nov 28, 2022 21:07 |
|
That Works posted:Who do you like for Jack stands? I defer to others /AI I just know that harbor freight has had to recall a LOT of jackstands for what amount to complete lack of QC on their castings. Basically same as every thing else they sell but it's PPE to keep the car from mushing you.
|
# ? Nov 28, 2022 21:27 |
|
sharkytm posted:Very cool. 22" blades, no guards, long sleeves, everyone hatted... the 40s were wacky. There was a war on, mister! People get hurt in wars. Also the blade had a guard. Carbide tipped blades and cutters was a thing yet to be discovered. Guys with the table saw were the scary part, imo. They had basically no idea what they were doing. Mr. Mambold fucked around with this message at 22:28 on Nov 28, 2022 |
# ? Nov 28, 2022 22:26 |
|
When I was a kid we had an old hand built table saw, motor on the floor with a huge belt, from probably the drat 30's that we used for everything. A terrifying piece of equipment but I do still have all my fingers so.....
|
# ? Nov 28, 2022 22:31 |
|
H110Hawk posted:I defer to others /AI I just know that harbor freight has had to recall a LOT of jackstands for what amount to complete lack of QC on their castings. Basically same as every thing else they sell but it's PPE to keep the car from mushing you. It was welds one time, castings another time.....yeah, don't trust them. I and several others in here have the Pro-Lifts with the extra locking pin you can put in the ratchet once it's at the height you want. I bought a set of 3 and 6 tons as soon as I heard about the HF stand recall here. They are very very obviously much higher quality.
|
# ? Nov 28, 2022 22:57 |
|
Why would you use jack stands when you could steal 12" oak blocks from work?
|
# ? Nov 28, 2022 23:06 |
|
Motronic posted:It was welds one time, castings another time.....yeah, don't trust them. It's comically hard to track and I believe they literally had to do what amounted to a complete recall of their various lines of them, including one of the replacement lines for the original recall. (Might be just the second line they had to recall were the store replacement models for the first recalled ones.) Given the quality of them its my opinion accuracy isn't important because they are all not to be trusted. I wonder if the weld failed ones would show casting flaws if the welds had held up?
|
# ? Nov 28, 2022 23:11 |
|
sharkytm posted:Very cool. 22" blades, no guards, long sleeves, everyone hatted... the 40s were wacky. Back when men were men and sheep were scared Are hats unsafe around power tools? Or are you just pointing out how old timey they looked FISHMANPET posted:My favorite part is the very beginning, talking about how table saws were old-fashioned and you spent so much time setting up for the next cut. And now 60-80 years later we decided that maybe the safety benefits of the table saw were worth the extra time spent in setup. Then again that table saw they were showing looked pretty basic, possibly even handmade, I wonder what DeWalt and Stanley and others were making in the realm of big-rear end industrial table saws in the 40s. Haha good call , that didn’t even register as a table saw at first. I dunno wtf they were doing w it to get that chopping action with it from below To be fair, I think RAS is better compared with mitre saw than a table saw, and it’s still probably the superior tool for cross cuts and simple miter cuts. Maybe not for exact compound cutting or trim stuff, but man those RAS just seem like such workhorses. I worked with an old timer who told me that trailer-mounted radial arm saws were at all the production framing sites in his day and they would run all day, gang cutting their way through a cut list. Those were all square cuts though, nothing like the creativity on display in that DeWalt video.
|
# ? Nov 28, 2022 23:58 |
|
BIG-DICK-BUTT-gently caress posted:Super cool video showing how they used radial arm saws in a production manner during WWII: The lumber industry's contribution to the war effort is often forgotten compared to tanks, trucks, ships and guns, but it was HUGE. Tons of bases and training camps shot up overnight, not to mention bridging timbers, crates, etc. and that increase in capacity made the postwar housing boom in large part possible.
|
# ? Nov 29, 2022 01:00 |
|
I remember sears used to sell a hss shaper head just like that with removable cutters. That seemed dicey. Those big radial arms on a trailer were definitely a thing back in the day. Frame carpenters didn't need a whole lot of tools. That was all Dewalt was known for for quite some time until they branched out around the 80s I guess.
|
# ? Nov 29, 2022 02:02 |
|
Squibbles posted:Just watch out for their transmission jacks apparently To be fair that is a massive transmission that is uniquely unwieldy even as far as transmissions go. But seeing how it racked over, I'm glad I have the "worse" HF scissor-style jack for that sort of work.
|
# ? Nov 29, 2022 03:46 |
|
Mr. Mambold posted:I remember sears used to sell a hss shaper head just like that with removable cutters. That seemed dicey. DeWalt did less "branching out" and more "jettisoning the business". Stanley (now, of course, Stanley Black & Decker) bought them in 1960 and sold the RAS business in 1989, turning the brand into generic power tools.
|
# ? Nov 29, 2022 04:03 |
|
The only stuff I get at HF are things that fall into "how could you make a version that doesn't work," "it has to work exactly once," and a small mountain of those little boxcutters they have at the checkout. "If it breaks, I get mushed" is right out. I'm also surprised how many of their ratcheting bar clamps I've destroyed via light duty use.
|
# ? Nov 29, 2022 05:16 |
|
IOwnCalculus posted:To be fair that is a massive transmission that is uniquely unwieldy even as far as transmissions go. But seeing how it racked over, I'm glad I have the "worse" HF scissor-style jack for that sort of work. For sure, but it was rated for more than the weight he used, and as he points out in the video it's pretty poorly made in general. I'm thinking the way to consider hf stuff is, "is there any way this could possibly kill or main me if it falls?" If yes, look elsewhere.
|
# ? Nov 29, 2022 05:38 |
|
Do we have a harbor freight dremel with various death wheels on them? Yes. Do we only use them with 3M not counterfeit safety glasses? Also yes. Mush is low on my list of things to be in a given day.
|
# ? Nov 29, 2022 06:51 |
|
Kaiser Schnitzel posted:I have almost that exact saw, probably made in the 50s. Mine is 14 or 16" and I think the ones in that video look bigger, but even just crosscutting with mine scares me to death, much less doing all the stuff they show there. The shaper/moulder head is cool as heck and the idea of a shaper head that can move around like that is seriously tempting and could be very useful, but also holy gently caress scary. Do you still use the RAS for anything? I still see them used at the home centers for cross cutting lumber, surprisingly enough. I want one when i have the space, if only for the historical significance.
|
# ? Nov 29, 2022 12:57 |
|
I'm looking for a high pressure washer that's more powerful and durable than your usual consumer grade stuff. I found this one for 40 euros which is about my budget! Looks pretty brutal. 3ph motor, 4kw and it runs. But not problem free. Might have frozen. The pump casting isn't broken but seller says there's leakage at the pistons. Pump uses four separate stages pistons to increase pressure each time. It's designed to work with hot water as well. I'm not too familiar with these kinds of pumps though and what could be wrong with it. Hoping it's something fixable, or I just got a pile of scrap except the motor. But 40 bucks is about what the motor is worth.
|
# ? Nov 29, 2022 14:14 |
|
See if you can get a make/model off of the pump itself. Hopefully it is something that rebuild or seal kits are available for. I'm more familiar with the CAT or general triplex pumps, but those are not a big deal to rebuild.
|
# ? Nov 29, 2022 14:59 |
|
BIG-DICK-BUTT-gently caress posted:Do you still use the RAS for anything? I still see them used at the home centers for cross cutting lumber, surprisingly enough. I want one when i have the space, if only for the historical significance. I really don’t because my sliding 12” miter saw has almost the same reach and is much, much less scary. If I had a smaller/less scary RAS I think I would keep a dado stack in it and use it for tenoning and cross-cutting dados.
|
# ? Nov 29, 2022 17:37 |
|
|
# ? May 29, 2024 18:50 |
|
Squibbles posted:For sure, but it was rated for more than the weight he used, and as he points out in the video it's pretty poorly made in general. Yeah, I'm not suggesting that it should have failed in that situation - but looking at how tall that transmission is, I'm not the least bit surprised that it did. The chain holddown setup on it looks so loving flimsy, I'd trust a no-name ratchet strap more. I've only used my scissor-style one for much lighter weight things anyway. I think the heaviest I've had on it was either a half full gas tank or a transfer case.
|
# ? Nov 29, 2022 18:16 |