|
Deceptor101 posted:I like the idea of craftsman, because when it breaks I can take it in and get it replaced for free, rather than sending it out in the mail. Yeah, for 90 days to 2 years, depending on what you buy. torque wrenches aren't covered by the lifetime guarantee. http://www.craftsman.com/cswarranty/nb-100000000227082#point2
|
# ? Apr 12, 2013 06:24 |
|
|
# ? May 25, 2024 14:50 |
|
Deceptor101 posted:So one of the last things in my "portable tool setup" (not air) I need is a good torque wrench. Currently I'm using this fine specimen which has actually gotten me through quite a bit. These do still have their uses. You can't measure breakaway torque with a clicker wrench, but you can with that one. I have that exact same one, in fact, bought for just that purpose. I needed to swap input flanges when I did my diff swap, and needed to know the breakaway torque for each so I could put the flanges back on without overtorquing and screwing up the preload. That said, I'd grab the 1/4" and 3/8" clickers from Harbor Freight. They're cheap as hell and work well. However, for a 1/2" I'd spend a bit more and step up to something like this to get the 250 ft-lb range. The HF 1/2" drive only goes up to 150 ft-lb.
|
# ? Apr 12, 2013 07:28 |
|
That digital Craftsman looks to be a "same factory in Taiwan" job, it's identical to my Clarke one and the Sealey one I got my dad. Perfectly good bit of kit with lots of useful functions - peak hold, saved torques, cumulative angular measurement etc.
|
# ? Apr 12, 2013 08:07 |
|
I'm looking to avoid HF, as I've had bad luck with my 1/4 in/lb torque wrench from them, and I've budgeted a bit more money. I was not aware of the lack of the lifetime warranty on the craftsman torque wrenches though, so I'll have to think about it more.
|
# ? Apr 12, 2013 20:59 |
|
So, I would appreciate recommendations for a tool as a gift. My neighbor is a great guy and he is turning 50. His wife invited Mrs. Slidebite and I over for a party they are hosting in a couple weeks. He is a very smart guy but lacks a lot of tools (and tool-sense). I lend him stuff fairly often, but it's not always the same thing. Things like my power rake attachment for the lawnmower, sledge hammer, 12" long 3/8 drill bit, test light, snake, etc. I'd like something sort of unique that "most" non-tool guys would never buy themselves but at the same time is very handy. He does have the basic hand tools. Stuff like 3/8 ratchet set (which would be adequate for jobs he would tackle) and screw driver and wrench set. I also think the odd thing like a multi-meter and crimp ends. I thought of a little 5 gal compressor set, but I don't know how often he'd actually use it... but it's probably still my front runner. Ideas? Probably like to keep it around the $50-ish range (maybe up to $100 if it is really worth while). Homeowner, RV owner, typical upper middle class dude.
|
# ? Apr 13, 2013 18:18 |
|
http://www.amazon.com/Stanley-85-610-10-Inch-MaxGrip-Adjustable/dp/B00009OYGZ for the first thing. Hell, every single person who sees mine says "holy poo poo! where did you get that?!" I can't think of anything else off the top of my head, but I firmly believe that everyone should own one of those. Maybe an assortment of quality crimp terminals and http://www.amazon.com/Stanley-85-610-10-Inch-MaxGrip-Adjustable/dp/B00009OYGZ? A quality crimper like that is worth its weight in gold, most people (including me, previously) don't trust crimp terminals because they're used to mashing them with a pair of pliers or a $7 stamped sheetmetal crimper and using crap terminals. kastein fucked around with this message at 18:28 on Apr 13, 2013 |
# ? Apr 13, 2013 18:26 |
|
Nobody has ever said, "yeah, I totally regret picking up a set of flexible head Gear Wrenches" ever.
|
# ? Apr 13, 2013 18:42 |
|
Let me be the first, then, to say I totally regret picking up a set of flexible head Gear Wrenches. I wish I'd have gotten the non-flexible head ones. The heads keep bending away when I try to put pressure on it. The straight SAE set I have is so much better than my flex-head metric set.kastein posted:http://www.amazon.com/Stanley-85-610-10-Inch-MaxGrip-Adjustable/dp/B00009OYGZ for the first thing. Hell, every single person who sees mine says "holy poo poo! where did you get that?!" grover fucked around with this message at 18:45 on Apr 13, 2013 |
# ? Apr 13, 2013 18:42 |
|
Here are some tools I never would have splurged on initially, but now can't live without: - GOOD crescent wrenches, like this locking one or nice Stanley one. I made do with cheapo crescent wrenches that could never hold their position and it infuriated me to no end. With a couple good ones now I rarely need my wrench set. - Ratcheting wrenches, like these GearWrench brand ones. I thought these were just unnecessary and expensive junk, but after using a few from a friend I was converted. For working on cars these are great because you can really jam them up into tight and uncomfortable spots and ratchet out a nut in seconds. - Head lamp. It's a cheap no brainer purchase that makes working on stuff so much easier when you have two hands free. - Extendible ratchet. This is a fantastic ratchet for the price. The action is really smooth, having both 3/8" and 1/4" heads is handy (no more fumbling for stupid tiny adapters), and the extension gives a nice amount of torque when you need it. This is the ratchet I reach for when working on cars. - Wobble extensions. These are a million times more useful than u-joint adapters in my experience. You get just enough play to get into almost any tight spot, but don't have your socket flopping around everywhere. If somebody would have given me those tools when I first started working on cars, it would have saved hours of cursing and busted knuckles.
|
# ? Apr 13, 2013 18:44 |
|
Oh yeah, Adam Savage recently did a nice podcast on essential tools. Lots of good advice on stuff to cut, glue, fasten, etc. https://www.youtube.com/watch?v=Nprbd76FFFI
|
# ? Apr 13, 2013 18:53 |
|
grover posted:Let me be the first, then, to say I totally regret picking up a set of flexible head Gear Wrenches. I wish I'd have gotten the non-flexible head ones. The heads keep bending away when I try to put pressure on it. The straight SAE set I have is so much better than my flex-head metric set. I got both so I'd be set.
|
# ? Apr 13, 2013 19:34 |
|
grover posted:Let me be the first, then, to say I totally regret picking up a set of flexible head Gear Wrenches. I wish I'd have gotten the non-flexible head ones. The heads keep bending away when I try to put pressure on it. The straight SAE set I have is so much better than my flex-head metric set. Yeah, but you're wrong about everything so the point still stands. VVV - Good crimpers and strippers are always worth it. Phone fucked around with this message at 21:58 on Apr 13, 2013 |
# ? Apr 13, 2013 20:28 |
|
Phone posted:Yeah, but you're wrong about everything so the point still stands. Im not allowed to just post "This.", so heres a link to a tool I was very happy with and is well worth the money: http://www.harborfreight.com/ratcheting-crimping-tool-97420.html
|
# ? Apr 13, 2013 21:46 |
|
kastein posted:http://www.amazon.com/Stanley-85-610-10-Inch-MaxGrip-Adjustable/dp/B00009OYGZ for the first thing. Hell, every single person who sees mine says "holy poo poo! where did you get that?!" Ratcheting wrenches. I use mine all the time. He probably just hasn't been introduced to the handiness that they are. That's a good idea too. Thanks guys, any more keep them coming
|
# ? Apr 13, 2013 22:18 |
|
Anyone know where I can get a 12-point Multi-Point driver? VW head gasket bolts...
|
# ? Apr 13, 2013 22:51 |
|
I think I got mine at Atuozone. Otherwise, ECS Tuning has some...
|
# ? Apr 13, 2013 22:59 |
|
Uthor posted:I think I got mine at Atuozone. Otherwise, ECS Tuning has some... Autozone and Advanced both only had 6 point Torx.. hmm.. off to Sears. Apparently Torx 55 should work.
|
# ? Apr 13, 2013 23:04 |
|
Polish posted:Autozone and Advanced both only had 6 point Torx.. hmm.. off to Sears. Apparently Torx 55 should work. Advance has it. But most employees don't know what/where it is. Part number AC835. http://shop.advanceautoparts.com/we...point+autocraft
|
# ? Apr 14, 2013 02:01 |
|
I finally go a chance to try out the welder. I just put a small bead on an old wrench that was laying on the workbench just to make sure everything works. This was my first time to ever weld and I must say that I couldn't imagine ever welding with a non-darkening hood. For a $90 hood it works very well. The only odd thing is that it doesn't play nice with the fluorescent lights in the garage as they caused the hood to darken.
|
# ? Apr 14, 2013 03:16 |
|
bung posted:I finally go a chance to try out the welder. I just put a small bead on an old wrench that was laying on the workbench just to make sure everything works. This was my first time to ever weld and I must say that I couldn't imagine ever welding with a non-darkening hood. For a $90 hood it works very well. The only odd thing is that it doesn't play nice with the fluorescent lights in the garage as they caused the hood to darken. Yeah, I have to use halogen lighting on the welding bench instead of a CFL droplight, thanks to the hood's sensors. It only flips out if the bulb is directly in view, so the fluorescent lights on the ceiling don't bother it. And autodarkening helmets are the loving best thing ever invented. Nothing like actually being able to SEE what you are doing as you start doing it...
|
# ? Apr 14, 2013 04:07 |
|
Phone posted:Nobody has ever said, "yeah, I totally regret picking up a set of locking flexible head Gear Wrenches" ever. Fixed that for you. The non-lockers are frankly a bag of poo poo for a lot of jobs.
|
# ? Apr 14, 2013 04:12 |
|
Splizwarf posted:Fixed that for you. The non-lockers are frankly a bag of poo poo for a lot of jobs.
|
# ? Apr 14, 2013 05:36 |
|
dyne posted:You guys know you can tighten them.....right? Mine are nice and stiff and take a little effort to flex. My SAE straight set is craftsman; my flex-head metrix set is Pittsburg. No complaints aside from the flex head not locking.
|
# ? Apr 14, 2013 13:44 |
|
bung posted:This was my first time to ever weld and I must say that I couldn't imagine ever welding with a non-darkening hood. Because it's your first time welding and you've not used a regular hood before. It's not that hard. In fact, once you learn the right head flip you don't have to touch it to flip it down. I've used auto-darkening hoods and yeah...they're nice. But not nice enough for me to replace my regular hood.
|
# ? Apr 14, 2013 14:18 |
|
dyne posted:You guys know you can tighten them.....right? Mine are nice and stiff and take a little effort to flex. I didn't, the ones I've used have been loaners. I own lockers, so I didn't look too deeply into the matter. How are they tightened?
|
# ? Apr 14, 2013 15:08 |
|
Motronic posted:Because it's your first time welding and you've not used a regular hood before. Headband design issue aside, I really like my auto darkening mask. When I got my MIG I discovered my normal one for arc welding was way too dark, so I decided to get an auto one as I needed to buy another one anyway. I'd used one before for MIG elsewhere and liked it.
|
# ? Apr 14, 2013 23:12 |
|
Splizwarf posted:I didn't, the ones I've used have been loaners. I own lockers, so I didn't look too deeply into the matter. How are they tightened? My gearwrench set uses a small hex socket head screw at the pivot
|
# ? Apr 15, 2013 00:10 |
|
Polish posted:Autozone and Advanced both only had 6 point Torx.. hmm.. off to Sears. Apparently Torx 55 should work. 6 point Torx 55 works just fine - did my Skoda head gasket last week with one...
|
# ? Apr 15, 2013 00:37 |
|
dyne posted:My gearwrench set uses a small hex socket head screw at the pivot I wonder what happens if I tighten that screw on my locking ones? I didn't think it was more than a wrist pin. It would be rad if they were a little less floppy.
|
# ? Apr 15, 2013 00:50 |
|
So, in case you all were curious, I ended up getting the craftsman Digi-tork 1/2 wrench. It's 25-250 ft/lbs which is nice and versatile, and thanks to being a !Craftsman Club! member, I got an additional $20 off ($80 instead of retail $120) which I spent $15 of on a 3-year warranty (instead of the pathetic 90-day one).
|
# ? Apr 15, 2013 02:10 |
|
Could someone give me an idea on how good of a deal this is: http://portland.craigslist.org/wsc/tls/3742411808.html I don't currently have a compressor or any air tools, and all of my car work is done in my single-stall apartment garage. A good compressor and tools are something I want to get at some point, though.
|
# ? Apr 15, 2013 22:21 |
|
I'd be astonished if that weren't a 240 volt compressor, so it's probably not going to be of much use to you. Also, you hardly need something that big to run air tools for your own purposes. It would be great to have, but you can definitely get away with something much smaller. Also, that's a fairly cheaply made compressor and can be had for $500 new: http://www.fleetfarm.com/detail/magna-force-60-gal-vertical-air-compressor/0000000069119
|
# ? Apr 16, 2013 01:47 |
|
hahahaha, did that guy seriously list the compressor for 150 over new price? Well, I guess it is still on the pallet, and he does have to deal with a bunch of low balling idiots on CL, so jacking the price up a bit to start is somewhat understandable. It also appears to include some air ratchets and impact wrenches.
|
# ? Apr 16, 2013 01:50 |
|
It's not "new on pallet" though, he's used it enough to need to replace parts (with high quality parts! Thousands invested!). The value over the $500 is more likely in the two air guns and two air ratchets included in the deal.
|
# ? Apr 16, 2013 01:53 |
|
Splizwarf posted:It's not "new on pallet" though, he's used it enough to need to replace parts (with high quality parts! Thousands invested!). The value over the $500 is more likely in the two air guns and two air ratchets included in the deal. If his taste in compressors is the same as his taste in air tools they are probably $150 new for the pair.
|
# ? Apr 16, 2013 02:05 |
|
You're right. One's a Campbell Hausfeld, which upon Googling I said out loud "holy poo poo, what" because I had no idea you could get even a worthless air wrench for under
|
# ? Apr 16, 2013 02:15 |
|
A somewhat related question, is there any small, portable compressor worth a drat that can power air tools like a 1/2" impact? Something you could transport in the back of a car and run in a garage without deafening yourself. I imagine it's a pipe dream but am curious.
|
# ? Apr 16, 2013 02:46 |
|
mod sassinator posted:A somewhat related question, is there any small, portable compressor worth a drat that can power air tools like a 1/2" impact? Something you could transport in the back of a car and run in a garage without deafening yourself. I imagine it's a pipe dream but am curious. Something like this works just fine. Yeah, you're gonna have to wait a bit if you want to take off all 4 wheels like you're doing a pit stop, but it will work fine for almost all home type situations. Other than painting a whole car or 3/4" drive and larger stuff. If you can find an older one (early 90s) they have 2.5 HP motors or larger on them and work much better. I'd pay the same price as a new one for an old one in good shape.
|
# ? Apr 16, 2013 03:03 |
|
Hah, yeah. Looking at some of the other pictures, the plate on it even says 230V. Oh well.
|
# ? Apr 16, 2013 03:04 |
|
|
# ? May 25, 2024 14:50 |
|
Motronic posted:Something like this works just fine. I have the craftsman 3 gallon one and it works great for exactly that. You wont be sanding or painting with it, but basic air tool stuff is fine
|
# ? Apr 16, 2013 03:40 |