|
Splizwarf posted:Prevent lifting by overlapping the doors. The hinges are the vulnerable point with barn doors, usually. Good point. A nice big board held in place with inward facing coach bolts would probably do it. I've been trying to think of a way of sort of sealing the gap between the doors and that would be quite adequate. The main garage door is super exposed so I couldn't see anyone trying anything too elaborate in a dead quiet residential street. My house is sort of flanked by a car dealership / service center and what is / was a truck mechanic so my place would be a bit of a poor target.
|
# ? Aug 27, 2013 04:14 |
|
|
# ? May 16, 2024 17:14 |
|
My tool anti-theft method is to leave everything strewn about the garage haphazardly.
|
# ? Aug 27, 2013 23:54 |
|
kmcormick9 posted:Can anybody recommend a good electric screwdriver? If you want to dish out some monies, you cant get better than the Snap On 7.2V For something so small, it packs a great punch. http://buy1.snapon.com/catalog/item.asp?P65=yes&tool=all&item_ID=647099&group_ID=682669&store=snapon-store&dir=catalog
|
# ? Aug 28, 2013 00:38 |
|
revmoo posted:My tool anti-theft method is to leave everything strewn about the garage haphazardly.
|
# ? Aug 28, 2013 00:54 |
|
grover posted:That pretty much sums up my tool drawer organization, too. Toolboxes are expensive! Screw wasting space with foam, I cram as much as I can in each drawer and still be able to close it. Socket rails and spanner/wrench rails make for a good compromise. Everything has a place, is kept neat and tidy, but minimal space wasteage:
|
# ? Aug 28, 2013 02:02 |
|
More importantly it keeps you noticing if anythings missing. Buying the same nice tool again is lame.
|
# ? Aug 28, 2013 06:37 |
|
It's time for me to buy a trolley jack, I'd like something light because I'm not a big guy, low profile would be nice too, it's for an E46. Any suggestions?
|
# ? Sep 2, 2013 21:11 |
|
Cakefool posted:It's time for me to buy a trolley jack, I'd like something light because I'm not a big guy, low profile would be nice too, it's for an E46. Any suggestions? I didn't think E46s were spectacularly low. You sure a regular jack that goes down to 125mm or so won't be low enough?
|
# ? Sep 2, 2013 21:41 |
|
Mooseykins posted:Socket rails and spanner/wrench rails make for a good compromise. Everything has a place, is kept neat and tidy, but minimal space wasteage: So is that what those things are called? Because I have been looking for those things for ages. My most used tools are living in a Chinese socket set case thing I was given when I was a kid. Big fold open plastic thing. It's been steadily turning to dust but I have no other good way of organizing my sockets and spanners. Admittedly what I have in the box is only a subset. I also have the big drawer in one of my toolchests full of sockets, extensions and drivers. So messy. My poor chest is overflowing. My 3/4" stuff lives in one of those plastic carpenters toolbox things etc. I've dreamed of a way of organising all of them nicely. Except for the imperial sockets and spanners which could live in an old bucket for all it matters because the only time I ever use them is when I've misplaced a metric.
|
# ? Sep 2, 2013 21:54 |
|
InitialDave posted:Sign up for one of Machine Mart's discount offers, and when they give you a VAT-free day, have a look at their stuff. They'll do a low (~80mm min height) trolley jack at £40 in steel (CTJ2250LP, 2 ton) or £90 in aluminium (CTJ1250A, 1.25 ton). Couple of their more expensive ones go that low, too. I dunno, I'm just getting all excited about having a new car and I've made do until 32 without a proper jack, I'll wait until I've got the car and check.
|
# ? Sep 2, 2013 22:53 |
|
Cakefool posted:It's time for me to buy a trolley jack, I'd like something light because I'm not a big guy, low profile would be nice too, it's for an E46. Any suggestions? While it's not light (at all..) Costs sell a really good Arcan low-entre jack for 80-100. Excellent value for money, i've had mine for about 6 years and it's never once let me down, it's a beast of a jack. While it's heavy, i can lift it and i'm 5'11" and 147lb, so shouldn't be too troublesome. You rarely need to pick up a jack anyway. General_Failure posted:So is that what those things are called? Because I have been looking for those things for ages. My most used tools are living in a Chinese socket set case thing I was given when I was a kid. Big fold open plastic thing. It's been steadily turning to dust but I have no other good way of organizing my sockets and spanners. Admittedly what I have in the box is only a subset. I also have the big drawer in one of my toolchests full of sockets, extensions and drivers. So messy. My poor chest is overflowing. My 3/4" stuff lives in one of those plastic carpenters toolbox things etc. Yessir. They're very handy. At some point i'll actually get around to riveting/welding them to a sheet of steel/ally in the drawer to hold them in there more solid. I like them more than the plastic holders and can cram more in there. That drawer is pretty full. The whole box is drat near full capacity and i need to make up a steel brace to support it as the floor of the box can't take the weight. Scores a very nice, very rare and expensive BMW/Land Rover genuine ball joint splitter earlier, a friend had one and just gave it to me. $370 from Samstag Sales. Also got a free Czechoslovakian scissor jack the other day, will work nicely for small tasks like aligning engines and such.
|
# ? Sep 3, 2013 00:06 |
|
General_Failure posted:So is that what those things are called? Because I have been looking for those things for ages. My most used tools are living in a Chinese socket set case thing I was given when I was a kid. Big fold open plastic thing. It's been steadily turning to dust but I have no other good way of organizing my sockets and spanners. Admittedly what I have in the box is only a subset. I also have the big drawer in one of my toolchests full of sockets, extensions and drivers. So messy. My poor chest is overflowing. My 3/4" stuff lives in one of those plastic carpenters toolbox things etc. I really like these for organizing my sockets. http://www.amazon.com/Hansen-HNE9302-Metric-Socket-Tray/dp/B009RTJO4I/ This is what they look like.
|
# ? Sep 3, 2013 23:21 |
|
Brain Issues posted:I really like these for organizing my sockets. http://www.amazon.com/Hansen-HNE9302-Metric-Socket-Tray/dp/B009RTJO4I/ I have a bunch of those (somewhere..) but i find that they either don't have enough spacer or i have gaps left by useless sizes. (like 20mm.) Also with the limited space in the box, i need the rails to make everything fit, and it's still a squeeze.
|
# ? Sep 3, 2013 23:45 |
|
Mooseykins posted:I have a bunch of those (somewhere..) but i find that they either don't have enough spacer or i have gaps left by useless sizes. (like 20mm.) Also with the limited space in the box, i need the rails to make everything fit, and it's still a squeeze. Yeah, if I was as cramped for space as you I'd have to find another solution but my toolbox is enormous. I like the convenience of not having to clip the socket to the rail and the tidy look/easiness of seeing what sizes are where that this style provides.
|
# ? Sep 4, 2013 00:04 |
|
Sears also sells these. They are my favorite socket organizer by far. The base has a graduated size so only the right size socket (and bigger...) fits on the peg. They make it easy to pick the sockets back in the right place. Considering how messy my tools are, this is the key for me.
|
# ? Sep 4, 2013 00:26 |
|
Brain Issues posted:Yeah, if I was as cramped for space as you I'd have to find another solution but my toolbox is enormous. I like the convenience of not having to clip the socket to the rail and the tidy look/easiness of seeing what sizes are where that this style provides. The box isn't all that small, it's just that there's so much stuff crammed into it. I need a bigger box but can't afford it. I'm actually quite fond of socket rails, they're simple and ultilitarian. (much like myself..) I just need to get them mounted properly and rearrange a few things to get it how it want.
|
# ? Sep 4, 2013 00:44 |
|
Brain Issues posted:I really like these for organizing my sockets. http://www.amazon.com/Hansen-HNE9302-Metric-Socket-Tray/dp/B009RTJO4I/ I just started using these because Lowe's is selling them for $5 per 3 piece set so you can have both metric and SAE for under . Metric SAE I also just picked up a set of Tongue and Groove Pliers because they had a set of 3 for under $10.
|
# ? Sep 4, 2013 01:28 |
|
Mooseykins posted:The box isn't all that small, it's just that there's so much stuff crammed into it. I need a bigger box but can't afford it. LOL isnt all that small... Nice digs
|
# ? Sep 4, 2013 01:39 |
|
Preoptopus posted:LOL isnt all that small... Thanks! Yeah, it's not so small, fucker weighs a hell of a lot (With all the drawers out it took 8 people to lift it into a van.) and is just about full, but organized enough that i know where everything is.
|
# ? Sep 4, 2013 01:46 |
|
Mooseykins posted:The box isn't all that small, it's just that there's so much stuff crammed into it. I need a bigger box but can't afford it. Yeah that's actually pretty drat big.
|
# ? Sep 4, 2013 01:49 |
|
Brain Issues posted:Yeah that's actually pretty drat big. It's quite rare to see a bigger box over here. (England) KRLs are quite unusual and few can afford them. My ratchet obsession: There's quite a few more since that pic was taken. (Total somewhere in the 70 region.)
|
# ? Sep 4, 2013 02:01 |
|
Wow I'm more jealous for the ratchet collection than the box.
|
# ? Sep 4, 2013 02:17 |
|
Mooseykins posted:It's quite rare to see a bigger box over here. (England) KRLs are quite unusual and few can afford them. Wow you're right, you really are running out of room... tell you what, mail all your duplicates to me and that should clear out some space for you!
|
# ? Sep 4, 2013 02:31 |
|
Viper915 posted:Wow you're right, you really are running out of room... tell you what, mail all your duplicates to me and that should clear out some space for you! Ha, you're not the first to say that!
|
# ? Sep 4, 2013 02:40 |
|
You know.... I really really like my composite ratchets from HF. Go and buy a set in 3/8, 1/4, and 1/2. For about 30 bucks they really are the best you can buy
|
# ? Sep 4, 2013 10:01 |
|
Splizwarf posted:What's the reason for the high cost? CNC-cut foam is pretty cheap. Hell, you can build a pretty nice CNC foam cutter for under $500. Ok I can't believe this. Please show me how I can make a cnc foam cutter for under 500 bucks.
|
# ? Sep 4, 2013 10:28 |
|
BrokenKnucklez posted:You know.... I really really like my composite ratchets from HF. Go and buy a set in 3/8, 1/4, and 1/2. For about 30 bucks they really are the best you can buy The only good ratchet I have is my 3/4" one. I'd love a good 1/2" and 3/8" one. I've never even owned a 1/4" one but would really like one. I also have breaker bars, those weird sliding T bars, a drill crank style one and this weird crank drill like one with a directional ratchet and a square chuck on the end. I have no idea what it's for but it's brilliant for thread taps e: I forgot the original reason I was posting. Can I attack connectors with a ratcheting crimper that I've already done with those awful nutcracker ones? I picked up a cheap ratcheting crimper today and I figure it has to be better than what I've got. General_Failure fucked around with this message at 10:59 on Sep 4, 2013 |
# ? Sep 4, 2013 10:56 |
|
Archives posted:Ok I can't believe this. Please show me how I can make a cnc foam cutter for under 500 bucks. Here's a CNC mill for under $600. https://www.inventables.com/technologies/desktop-cnc-mill-kits-shapeoko You could probably knock a hundred off the top if you built it yourself.
|
# ? Sep 4, 2013 13:37 |
|
BrokenKnucklez posted:You know.... I really really like my composite ratchets from HF. Go and buy a set in 3/8, 1/4, and 1/2. For about 30 bucks they really are the best you can buy These actually are very good. Nice in the cold too.
|
# ? Sep 4, 2013 16:13 |
|
Mooseykins posted:While it's not light (at all..) Costs sell a really good Arcan low-entre jack for £80-100. Excellent value for money, i've had mine for about 6 years and it's never once let me down, it's a beast of a jack. While it's heavy, i can lift it and i'm 5'11" and 147lb, so shouldn't be too troublesome. You rarely need to pick up a jack anyway.. Unfortunately I don't have a garage and the only place I can keep a jack is either in the boot or the shed. Either one requires the jack to be lifted & carried every time I use it.
|
# ? Sep 5, 2013 08:56 |
|
Cakefool posted:Unfortunately I don't have a garage and the only place I can keep a jack is either in the boot or the shed. Either one requires the jack to be lifted & carried every time I use it. Ah, fair enough. Yeah, while you can lift them in and out of the boot, they're heavy. I used to do a lot of mobile mech work, which almost always involved lifting that jack in and out of the car. It gets old real fast. Ally ones are good, but there are a lot of cheap ones that just aren't up to the job. Sealey make one, and my friend found it to buckle quite quickly. I recall Arcan do an ally one and it's pretty good. Blue Point make one which is good, but expensive.
|
# ? Sep 5, 2013 09:01 |
|
So my grandfather went into an old folks home and I managed to inherit some sweet old stahlwille tools. The thing i was wondering was if torque wrenches go "off" as these would be from the mid-late 50s or 60s. If they do go out of spec, how much it would cost to get them reset.
|
# ? Sep 5, 2013 09:04 |
|
Big Daddy Keynes posted:So my grandfather went into an old folks home and I managed to inherit some sweet old stahlwille tools. The thing i was wondering was if torque wrenches go "off" as these would be from the mid-late 50s or 60s. If they do go out of spec, how much it would cost to get them reset. Are they clickers or beam-type? Pictures? Stahlwille make some of the very best tools out there, absolute top quality.
|
# ? Sep 5, 2013 09:07 |
|
Top drawer with my most commonly used sockets, ratchets, extensions. Screwdriver/Torxdriver/Prybar/Picks/Trimtool drawer.
|
# ? Sep 6, 2013 00:07 |
|
Anyone have any experience with this nibbler: http://www.harborfreight.com/compact-hand-nibbler-65895.html I've used the ones like this before: and they're alright, but definitely feel cheap and sometimes get the chips caught in the mechanism. I know it's a bit silly to look at HF for something that doesn't feel as cheap, but I'm occasionally surprised.
|
# ? Sep 6, 2013 02:17 |
|
EZ Out? Bullshit. Fuckers need to be renamed to Difficult Out.
|
# ? Sep 6, 2013 04:40 |
|
Brain Issues posted:Top drawer with my most commonly used sockets, ratchets, extensions. I can get behind a tool box that has big enough drawers to fit cordless power tools into it!
|
# ? Sep 6, 2013 04:43 |
|
Brain Issues posted:Top drawer with my most commonly used sockets, ratchets, extensions. Love for the Wera!
|
# ? Sep 6, 2013 04:44 |
|
Brain Issues posted:Top drawer with my most commonly used sockets, ratchets, extensions. Nice collection you got going on there! Good to see the Weras, i'm a big fan of their screwdrivers. Wiha and PB Swiss are other brands to look into for stuff, i have many of their products and they're great. How do you like the Snap-on Instinct screwdrivers? I have a couple, but never really got on with them so much, probably because i have small hands and they don't "fit" so well in my grip. The vast majority of my Snap-on screwdrivers are the older hard handle type, which i'm very fond of. You need more ratchets though. I have one of those 3/8" DeWalt 10.8v impacts, surprisingly powerful for its size, i never expected it to remove half of the nuts/bolts that it does. It sees a lot of use, and the battery life is crazy too. Phone posted:EZ Out? Bullshit. Or EZ Break. Those fuckers snap and really ruin your day. Among many sets for different types of oh poo poo moments I have the Snap-on/Irwin short helical extractors like these: They work really well, and tend to be less prone to breakage than EZ Outs. Of course, when they do break they still gently caress up your day as good as an EZ Out does.
|
# ? Sep 6, 2013 05:47 |
|
|
# ? May 16, 2024 17:14 |
|
Mooseykins posted:Nice collection you got going on there! Good to see the Weras, i'm a big fan of their screwdrivers. Wiha and PB Swiss are other brands to look into for stuff, i have many of their products and they're great. I really like the snap on instinct screwdrivers. The Wera handles may have been ever so slightly more comfortable for me but the tips and shaft strength is much greater on the SnapOns. I still keep the Weras around, they worked fine and I would still be using them if I didn't get the SnapOn drivers for literally half price. The snapon drivers are nice but not worth it at full price in my opinion. I don't really need more ratchets! Between those and my 12v DeWalts and air tools I have all my bases covered, I haven't needed to borrow a ratchet from anyone. All my ratchets are SnapOn 72 or 80 teeth. The long ones are all flex head so they're really versatile. My favorite tools in the top drawer are the 12v DeWalts though, I use them on almost every single car that I work on, and unless its at a weird angle I don't even have to use a ratchet. They're pretty drat strong like you say and the battery life is incredible.
|
# ? Sep 6, 2013 15:33 |