|
I have a little 1/2"x1" neodymium magnet and it's great for finding drywall screws. A lot easier than the little magnets on swivels IMO. Plus you can just leave it stuck to the wall to mark where the stud is, instead of having to mark it with a pencil.
|
# ? Aug 19, 2016 16:38 |
|
|
# ? Jun 13, 2024 05:57 |
|
uwaeve posted:Just starting out, will I be relatively happy with an all-in one type blade for a table saw or am I better served swapping out blades depending on what I'm doing? I have the Freud Diablo 50t combo blade. It leaves nice buttery cuts in pretty much everything I have used it for it but it's a little slow and gums up quickly. I do very little crosscutting on my table saw so I replaced it with a Freud 24t ripping blade and I prefer the 24t. Much quicker feed rate, doesn't gum up much and it is quieter. Cheaper to have sharpened, too. Keep the pitch from building up and the 50t will do you well.
|
# ? Aug 19, 2016 21:56 |
|
Scored some old tools this am at a local yard sale. None of it chineseium, all for about $25.
|
# ? Aug 20, 2016 16:47 |
|
And now for something different, a saw blade made of paper! https://youtu.be/rYfkhdKcEiE
|
# ? Aug 21, 2016 17:46 |
|
The only thing I could think about during that video was massive papercuts
|
# ? Aug 21, 2016 17:56 |
|
kid sinister posted:And now for something different, a saw blade made of paper! That could actually be really useful for cutting pvc trim pieces or similar soft, expensive materials, or something where you want minimal kerf (or the world's worst papercut)
|
# ? Aug 21, 2016 18:02 |
|
Ok, gather 'round for three learning moments with the track saw. 1. It didn't cut square out of the box, needed some back and forth adjustment so that it not only cut square but the indicator corresponded to anything approaching reality. You can't loosen the indicator pointer without the stop adjustment screws backed out, but when they are backed out it's not set up square. So back and forth counting quarter turns of the stop screws, seeing what the indicator pointer said, etc. 2. The depth adjustment knob needs to be really tight. In the middle of a cut I put a little too much weight on the saw, because it slid the stop to the end, plunging through the 1" foam insulation and right onto the concrete floor. The tooth bevels no longer alternate. RIP $33, luckily I had ordered a second so I could keep working. I did wind up using the blade to offset measurements with a combination square, but I'm betting I could have gotten a 0.086" shim for less than $33. 3. At the 45 degree setting, the blade is offset from the splinter guard on the track enough that it makes a difference in the quality of the cut. The track has two edges, im thinking about making the other side 45 degrees (I haven't cut using that side yet, and you actually trim the rubber splinter guard on your first pass). Then I'm going to run into measuring and marking problems, though, with the rubber splinter guard being wider at the top than bottom. The splintering and tearout isn't dooming my project, but just an FYI for anyone cutting bevels like myself, the top surface will have stuff not held down by the splinter guard.
|
# ? Aug 23, 2016 02:33 |
|
You can also reduce tear out by doing a quick shallow scoring cut (I'd forgotten but one of the other Makita track saw features is a separate 2-3mm depth stop, so you can do a scoring cut without adjusting the depth)
|
# ? Aug 23, 2016 05:57 |
|
wormil posted:I bought a Proto feeler gauge from Amazon Warehouse (AWD) but it is missing the .002 and .003 leafs. Fired off an email to Proto and heard back pronto, they will send me a new one. Will update when it happens but so far that is good customer service. Update, arrived today via USPS. That's good service, will definitely buy more Proto stuff.
|
# ? Aug 24, 2016 03:08 |
|
What are good options for getting all the moisture and oil out of a compressed air line, and then cleaning any hoses and simple air blowers that might already have oil/water in them? I need to be able to clean my camera sensor and the little squeeze bulb puffers (even the nice rocket one) just aren't really cutting it. I'm thinking replacing the regulator to one with a filter system built in and then putting a second filter right at the tool might do the job?
|
# ? Aug 31, 2016 04:38 |
|
Parts Kit posted:What are good options for getting all the moisture and oil out of a compressed air line, and then cleaning any hoses and simple air blowers that might already have oil/water in them? I need to be able to clean my camera sensor and the little squeeze bulb puffers (even the nice rocket one) just aren't really cutting it. Personally, I would never use any of my compressors to try and clean a camera sensor- with one exception. My airbrush compressor. Driers and separators are cheap for them, you can also buy small disposable one-use filters.
|
# ? Aug 31, 2016 06:25 |
|
Parts Kit posted:What are good options for getting all the moisture and oil out of a compressed air line, and then cleaning any hoses and simple air blowers that might already have oil/water in them? I need to be able to clean my camera sensor and the little squeeze bulb puffers (even the nice rocket one) just aren't really cutting it. Why not get a sensor cleaning swab and do it right?
|
# ? Aug 31, 2016 14:43 |
|
Falco posted:Why not get a sensor cleaning swab and do it right? the spyder posted:Personally, I would never use any of my compressors to try and clean a camera sensor- with one exception. My airbrush compressor. Driers and separators are cheap for them, you can also buy small disposable one-use filters.
|
# ? Aug 31, 2016 23:29 |
|
Parts Kit posted:Do you really think I haven't done this? It absolutely wasn't clear and they were just trying to help..... Like, seriously. I don't care how clean the air is (within reason for a home gamer) a proper swab is going to be better. And cheaper.
|
# ? Sep 1, 2016 04:01 |
|
So the swabs haven’t removed the dust, but you think compressed air might? Maybe it’s worth a try, but I wouldn’t hold my breath.
|
# ? Sep 1, 2016 04:31 |
|
Sometimes they do, sometimes they don't and it becomes a marathon session where you go through a handful of the things. Swabs are really more for dealing with the stubborn fine stuff that sticks hard to the hot mirror anyways. Air bulbs are okay and generally get the large loose stuff the camera's sensor cleaning thing occasionally can't get off -- which is what is bugging me at the moment -- but usually when you squeeze them the nozzle moves all over the drat place so it's hard to put the air exactly where you want. There's also the issue that over time dust gets into nooks and crannies inside the body anyways (and this one is several years old) so being able to precisely direct some air would be quite helpful for getting that stuff out so that it doesn't just migrate later on. Unfortunately finding good info on using compressed air is difficult because search results mostly end up being folks trying to shortcut with lovely canned air and having obvious problems when they get propellant all over their sensor. ed: woo, finally found something useful in search results - American Recorder Technologies makes co2 cartridges without extra poo poo for cleaning sensors. Parts Kit fucked around with this message at 17:11 on Sep 1, 2016 |
# ? Sep 1, 2016 16:59 |
|
Got my 45 oz Estwing deadblow in today. I'd borrowed one from a coworker, and the improvement from a lighter, more standard one was drastic for shoving around big fixtures. Kinda worried about the faces getting damaged in the long run, but my application is pretty specialized, probably won't be a big issue. http://www.estwing.com/db_estwing_deadblow_hammers.php
|
# ? Sep 2, 2016 02:42 |
|
My dad retired and is selling his house so we're finding a lot of neat things as we pack everything. One of them we're not sure about; this aluminum tool. First look says pipe threader or chaser but then I think why aluminum? Has anybody seen one of these before? More pics: http://imgur.com/a/5lFAn
|
# ? Sep 2, 2016 04:34 |
|
Parts Kit posted:Sometimes they do, sometimes they don't and it becomes a marathon session where you go through a handful of the things. Swabs are really more for dealing with the stubborn fine stuff that sticks hard to the hot mirror anyways. Buy a can of compressed air that is made for electronic cleaning? Less than
|
# ? Sep 2, 2016 14:41 |
|
bred posted:My dad retired and is selling his house so we're finding a lot of neat things as we pack everything. One of them we're not sure about; this aluminum tool. First look says pipe threader or chaser but then I think why aluminum? Has anybody seen one of these before? https://gemm-sales.myshopify.com/products/ringer-sprinkler-repair-tool
|
# ? Sep 2, 2016 15:49 |
|
I was given a shower valve socket set and noticed that the sizes are unusual: 21/32, 27/32, 29/32, 31/32, 1-1/32, 1-3/32, 1-5/32, 1-9/32, 1-11/32, and 1-7/16 Is there a historical or other reason why they use such odd sizes?
|
# ? Sep 3, 2016 21:03 |
|
Supposedly before the advent of different grades of bolts, a stronger bolt of a different size had a slightly over sized head. I always figured nonstandard socket sizes/types were usually "because gently caress you, that's why".
|
# ? Sep 3, 2016 21:11 |
|
The extra size might also help for galvanized bolts?
|
# ? Sep 3, 2016 21:29 |
|
Does anyone own or have experience with the Milwaukee 12v circular saw? Its pretty pricey but I've seen the display model at the store and seems very well built and solid. I already have the 12v impact driver and drill so I would be buying just the tool with no extra battery; it runs $149.
|
# ? Sep 4, 2016 03:41 |
|
I have the 18v circular Milwaukee. Works fine for my intermittent use. It'll cut 2x4s all day.
|
# ? Sep 4, 2016 13:16 |
|
O cool, thanks!
|
# ? Sep 4, 2016 15:34 |
|
Is there like a dremel attachment that uses the rotation to blow a stream of air or did I just invent it in my head?
|
# ? Sep 5, 2016 13:03 |
|
Spookydonut posted:Is there like a dremel attachment that uses the rotation to blow a stream of air or did I just invent it in my head? quote:The 490 Dremel Dust Blower offers an innovative solution for improving visibility when using your Dremel rotary tool. By removing fine debris from your line-of-sight, our small air blower is great for detailed projects, sanding, engraving, and carving. Can also be used on the 225-01 Flex Shaft attachment.
|
# ? Sep 5, 2016 13:07 |
|
I recently got into wood carving using an angle grinder and I can tell my 10 buck harbor freight grinder is not long for this world. Any recommendations for a new grinder for when mine gives up the ghost? I'm leaning towards a paddle switch model right now.
|
# ? Sep 5, 2016 13:18 |
|
I have the Hitachi 5" variable speed grinder and it is a joy to use. Lots of power, low vibration.
|
# ? Sep 5, 2016 18:27 |
|
coathat posted:I recently got into wood carving using an angle grinder and I can tell my 10 buck harbor freight grinder is not long for this world. Any recommendations for a new grinder for when mine gives up the ghost? I'm leaning towards a paddle switch model right now. My harbor freight angle grinder just died a couple weeks ago after almost 10 years of rugged abuse. It sounded horrible from day 1 but it definitely lasted. I got a makita to replace it and have no complaints.
|
# ? Sep 5, 2016 18:39 |
|
Spookydonut posted:Is there like a dremel attachment that uses the rotation to blow a stream of air or did I just invent it in my head? You can use a strip of tape around the shaft as a make shift fan in a pinch.
|
# ? Sep 5, 2016 18:45 |
|
coathat posted:I recently got into wood carving using an angle grinder and I can tell my 10 buck harbor freight grinder is not long for this world. Any recommendations for a new grinder for when mine gives up the ghost? I'm leaning towards a paddle switch model right now. Are you sure? Those HF grinders always sound like there's sand in the bearings, and the motors vibrate badly. They do, however, seem to last nearly forever. If you are doing carving, I'd strongly suggest a variable speed model, either from Makita, Bosch, or Metabo. They're expensive, but for wood, you really appreciate the finer control. Alternately, if you're using smaller blades, the 4" Makita is a nice grinder and very inexpensive, but spins 11,000RPM. $150 would buy you either a 5" or a 6" Makita Variable Speed, without any discounts/coupons. 5": https://smile.amazon.com/Makita-9565CV-5-Inch-Variable-Grinder/dp/B00005Q7BG 6": https://smile.amazon.com/Makita-9566CV-Variable-Cut-Off-Grinder/dp/B00006K15B sharkytm fucked around with this message at 22:31 on Sep 5, 2016 |
# ? Sep 5, 2016 22:29 |
|
wormil posted:I have the Hitachi 5" variable speed grinder and it is a joy to use. Lots of power, low vibration. I got a refurb hitachi from big sky tools as a Christmas gift awhile back, and it's definitely a huge step up from my harbor freight grinder. Thing feels rock solid, and I've had absolutely zero issues so far. It's even done great cutting through a concrete filled steel pipe. I've always heard Makita and Dewalt make excellent grinders as well
|
# ? Sep 5, 2016 23:04 |
|
sharkytm posted:Are you sure? Those HF grinders always sound like there's sand in the bearings, and the motors vibrate badly. They do, however, seem to last nearly forever. Yeah I might just see how long this one lasts and save up for a variable speed grinder. For now I'm going the ghetto route a second harbor freight grinder and their router speed controller for more control. Plus I don't have to switch out wheels since the carving blade I got has a little adaptor to that likes to fall out and run away when I take it off. The carbide cup wheel at harbor freight is one of their great tools. If you ever need to seriously shape some wood it's amazing and only ten bucks. http://t.harborfreight.com/power-tools/grinding-wheels-accessories/4-1-2-half-inch-carbide-cup-wheel-66613.html
|
# ? Sep 6, 2016 02:11 |
|
coathat posted:
Does this fall under the category of carcinogenic harbor freight abrasives to avoid, or is that just like their sandpaper and cutoff wheels?
|
# ? Sep 6, 2016 02:39 |
|
I've got a 4" Makita, 5"/6" Milwaukee, 4.5" Metabo, and a cordless Makita 4.5". The 4" gets a flapwheel, the 4.5 gets a fine stone, the 6" gets a coarse stone, and the cordless gets a cutoff for mobile use.
|
# ? Sep 6, 2016 03:01 |
|
I was thinking more something akin to a mini turbine or pump rather than a fan.
|
# ? Sep 6, 2016 15:02 |
|
Spookydonut posted:I was thinking more something akin to a mini turbine or pump rather than a fan. You mean something like this?
|
# ? Sep 6, 2016 16:28 |
|
|
# ? Jun 13, 2024 05:57 |
|
Home Depot has a few Makita's on sale right now: http://www.homedepot.com/b/Featured-Products-Labor-Day-Tools-and-Hardware/Makita/N-5yc1vZcedgZyg $100 for one of drill, driver, angle grinder, drill+driver combo (only 12V), or two batteries. Most people here probably have a drill and driver already, but $100 for an angle grinder or a couple spare batteries isn't too bad, right?
|
# ? Sep 6, 2016 16:33 |