|
QuarkJets posted:IIRC fridges with french doors cost way more, and stainless steel fridges cost way more. I personally see no utilitarian benefit from either of these things (there's an argument that french doors let you bend down less, but I don't think that's accurate), so keep that in mind if you don't care as much about those kinds of stylistic choices The french doors are because we don't have enough space for the the full open door. Perils of buying a 110 year old home.
|
# ? May 22, 2017 02:30 |
|
|
# ? May 9, 2024 01:43 |
|
Sab0921 posted:The french doors are because we don't have enough space for the the full open door. Perils of buying a 110 year old home. Even houses from the 50s have this issue. Like, say, mine.
|
# ? May 22, 2017 04:35 |
|
I just bought a fridge yesterday to replace the one that stopped holding temperature yesterday morning. It's definitely worth it to see and touch them in person. We bought a stainless steel fridge at our last house and I was really unimpressed with how dirty it looked from fingerprints, etc. When we looked yesterday I noticed that some models had much better the finishes were on some stainless models than others. Also, the quality of the plastics, lighting, etc. varied greatly between makes/models even on similarly priced units.
|
# ? May 22, 2017 05:49 |
|
Bring a magnet with you. Some fridges got it and some fridges don't.
|
# ? May 22, 2017 06:11 |
|
Next step for home ownership - turns out the cable and ethernet wiring just kind of terminate in the crawl space (no patch panel or anything of the sort). So it's wired for Cat5 and Co-Ax - but there is no terminal for either actually inside the freaking house. How do you go about remedying that situation so I can get Internet hooked up - seemingly leaving it hanging outside is not likely the best option here.
|
# ? May 22, 2017 16:50 |
|
Buy a punchdown tool and some cat5 termination blocks.
|
# ? May 22, 2017 17:02 |
|
HEY NONG MAN posted:Buy a punchdown tool and some cat5 termination blocks. Sure - I mean - I guess they're terminated properly inside the house - the wires just run through the bottom and kind of stick out of the crawlspace. Seemingly, there should be access somewhere in the actual home.
|
# ? May 22, 2017 17:03 |
|
How much slack? And is it just a bundle of cut cables sitting in the middle of the crawlspace? If you've got the slack, might be worth finding a closet from underneath and pulling them up through to it and terminating them in there
|
# ? May 23, 2017 13:02 |
|
couldcareless posted:How much slack? And is it just a bundle of cut cables sitting in the middle of the crawlspace? If you've got the slack, might be worth finding a closet from underneath and pulling them up through to it and terminating them in there Literally just a bundle of cut cables sitting in the crawlspace. There is a good amount of slack there, but not sure if enough to run to a closet, but can try.
|
# ? May 23, 2017 18:09 |
|
I recently replaced an oil-fed furnace with a natural gas unit. I live in the Pacific Northwest, I do not have air conditioning and I have a single story rambler with a walk-out basement that stays very cool year round. I mention this because our new furnace has an independent circulation fan that pulls air from the basement and circulates it throughout the house. We didn't have anything like this before and this is the first opportunity since installing it that we've been able to take advantage of it. My question: given that it's hot as balls outside and the ambient temperature in my house (on the main floor where the thermostat is) will never get below 70F on its own without a/c, is it ok to just run the fan all day to take advantage of the cool basement air or will I kill the unit doing that?
|
# ? May 24, 2017 00:15 |
|
You can and should run the fan to circulate air without having the heat on.
|
# ? May 24, 2017 00:20 |
|
HEY NONG MAN posted:I recently replaced an oil-fed furnace with a natural gas unit. I live in the Pacific Northwest, I do not have air conditioning and I have a single story rambler with a walk-out basement that stays very cool year round. That's a pretty cool setup. I've heard of attic fans to push hot air outside, but yours seems better. It's like... Geologic cooling!
|
# ? May 24, 2017 01:10 |
|
Sab0921 posted:Next step for home ownership - turns out the cable and ethernet wiring just kind of terminate in the crawl space (no patch panel or anything of the sort). So it's wired for Cat5 and Co-Ax - but there is no terminal for either actually inside the freaking house. How do you go about remedying that situation so I can get Internet hooked up - seemingly leaving it hanging outside is not likely the best option here. Seems like a good opportunity to come up with your own setup since you already have it in one place. One of the previous owners of my house installed ~8 different coax jacks in various rooms on different levels by running the cable outside and along the roof and drilling into the house through the brick wall.
|
# ? May 24, 2017 01:30 |
|
Drunk Tomato posted:That's a pretty cool setup. I've heard of attic fans to push hot air outside, but yours seems better. It's like... Geologic cooling! I am a bit skeptical that the basement has the capacity to cool a substantial quantity of air - but you may be able to reverse the stack effect.
|
# ? May 24, 2017 12:44 |
|
Drunk Tomato posted:That's a pretty cool setup. I've heard of attic fans to push hot air outside, but yours seems better. It's like... Geologic cooling! Hopefully not pulling a bunch of radon up too!
|
# ? May 24, 2017 13:25 |
|
devicenull posted:Hopefully not pulling a bunch of radon up too! Is this still a thing? We never talk about it in Canada, but I guess we never have.
|
# ? May 24, 2017 14:47 |
|
Bozart posted:I am a bit skeptical that the basement has the capacity to cool a substantial quantity of air - but you may be able to reverse the stack effect. It's nowhere close to an air conditioning effect but it keeps the air moving and it's better than what we had before.
|
# ? May 24, 2017 14:51 |
|
devicenull posted:Hopefully not pulling a bunch of radon up too! It does exactly this, negative pressure, but if the windows are open then it pulls from the source of least resistance.
|
# ? May 24, 2017 16:59 |
|
Subjunctive posted:Is this still a thing? We never talk about it in Canada, but I guess we never have. Radon is basically a thing anywhere you have shallow granite bedrock, usually towards the mountains or in areas that have seen a lot of geologic erosion. Radon comes from the normal decay of trace amounts of Uranium in the Granite -- you can actually get non-trivial quantities of Radon from a having a large amount of granite counter-tops in an area (if it's from a seam that has relatively high uranium content). The solution to Radon is generally just "blow it outside" since it readily disperses and is not really very harmful in the environment: the danger of Radon is that it will build up in confined areas without much airflow (like basements) and its decay components which do not disperse as readily will build up as radioactive dust.
|
# ? May 24, 2017 19:41 |
|
So the house that I bought has a pond... what do I do to get this thing running with some fish? If it were just up to me I'd probably take the whole thing out, but partner wants to get a pump and make a waterfall and add some koi/goldfish...
|
# ? May 26, 2017 15:00 |
|
metztli posted:I could use some advice about decks and things to look for in a deck contractor. Noooooooooooooo...... Don't doooo it. Deckover is garbage and should be avoided like the plague. It's wayy too thick, so it's a pain in the rear end to apply, has poo poo adhesion, and will start clumping off in a year or two. Do yourself a favor and use pressure treated lumber for the structural members of the deck, but get composite for the decking itself. It'll last for years and years with zero maintenance or splinters in your feet. Seriously, unless you live in Florida where everything is a sun baked hellhole with UV and heat that destroy everything even slightly exposed, go with composite boards and do not even think about Deckover.
|
# ? May 26, 2017 21:29 |
|
So for anyone not saving money each month for repairs... I just had to loan a parent $4000 to get a new dishwasher and water heater. Plan for that poo poo.
|
# ? May 27, 2017 00:11 |
|
Elysium posted:So the house that I bought has a pond... what do I do to get this thing running with some fish? That's nowhere near enough volume of water to keep fish alive. The issue is the temp swings on hot days vs. cold days. With so little water, the water temp will change very fast. Make the pond five times bigger, or just use it to grow plants (and mosquitoes). e. Just to be clear, you can totally put some small goldfish in there. They sell feeder fish at the pet store for very very cheap. Just don't expect them to live especially long. Also they will be raccoon food unless your yard is totally secure from raccoons (and cats).
|
# ? May 27, 2017 00:17 |
|
Woof Blitzer posted:So for anyone not saving money each month for repairs... I just had to loan a parent $4000 to get a new dishwasher and water heater. Plan for that poo poo. That seems like an awful lot of money for those two things
|
# ? May 27, 2017 00:30 |
|
Elysium posted:So the house that I bought has a pond... what do I do to get this thing running with some fish? I don't see a pond, just a potential mosquito pit that you should fill in
|
# ? May 27, 2017 00:33 |
|
Leperflesh posted:...unless your yard is totally secure from raccoons. There is no such thing.
|
# ? May 27, 2017 00:35 |
|
MrYenko posted:There is no such thing. Concur. After much effort I've managed to arrange my yard so that I never see skunks, possums, and stray cats in it, but I've still seen the occasional raccoon.
|
# ? May 27, 2017 02:12 |
I see raccoons get stuck inside dumpsters around here all the time, so just build the outside of your yard out of whatever the inside of dumpsters are made out of.
|
|
# ? May 27, 2017 03:28 |
|
raccoons are pretty uncommon in my area. Rats are the real problem.
|
# ? May 27, 2017 03:52 |
|
QuarkJets posted:IIRC fridges with french doors cost way more, and stainless steel fridges cost way more. I personally see no utilitarian benefit from either of these things (there's an argument that french doors let you bend down less, but I don't think that's accurate), so keep that in mind if you don't care as much about those kinds of stylistic choices Maybe I'm looking in the wrong places but I remember seeing very few refrigerators that weren't stainless steel and they didn't seem to be much cheaper.
|
# ? May 27, 2017 04:51 |
|
RICHUNCLEPENNYBAGS posted:Maybe I'm looking in the wrong places but I remember seeing very few refrigerators that weren't stainless steel and they didn't seem to be much cheaper. Unless you're looking at the low end of the scale it's not unheard of to be charged extra if you don't want SS since that's generally what gets stocked. I had to pay extra for a dishwasher recently specifically because I wanted in black instead of SS.
|
# ? May 27, 2017 06:59 |
|
Pryor on Fire posted:I see raccoons get stuck inside dumpsters around here all the time, so just build the outside of your yard out of whatever the inside of dumpsters are made out of. Just make your attic super appealing and they'll go in there instead of messing with your yard!
|
# ? May 27, 2017 14:17 |
|
RICHUNCLEPENNYBAGS posted:Maybe I'm looking in the wrong places but I remember seeing very few refrigerators that weren't stainless steel and they didn't seem to be much cheaper. Maybe you're looking in the wrong place, because you should be able to see this trend at basically any of the big hardware stores with a little comparative shopping. Popping over to the Lowes website, here are three fridges that are exactly alike except one's white, one's "easycare" (faux) stainless, and one's actually stainless: $429 - Frigidaire 18-cu ft Top-Freezer Refrigerator (White) $499 - Frigidaire 18-cu ft Top-Freezer Refrigerator (Easycare Stainless Steel) $579 - Frigidaire 18-cu ft Top-Freezer Refrigerator (Stainless) Last I checked you see similar price increases for buying side-by-side or french-door refrigerators. Top-Freezer refrigerators are ubiquitous because they're the cheapest
|
# ? May 28, 2017 09:35 |
|
Real stainless steel is more expensive then painted metal by a lot. That said $100 is only 1/5 of a juicero so.
|
# ? May 28, 2017 22:27 |
|
Here's my hot tip for fridge-buying: If it has a door alarm, check out how annoying it is. I have an LG fridge that really loves to beep. Its alarm can't be disabled, so when I clean the fridge I put a piece of tape over the sensor or put up with a soundtrack of one endless beep. It's very good at letting you know when you're taking too long looking for something or putting the groceries away, but didn't actually work the one time the door was slightly ajar and leaking -- I guess it wasn't open by enough.
|
# ? May 29, 2017 16:11 |
|
Interesting, my LG's alarm can be disabled. My wife loves it because I tend to graze through the fridge.
|
# ? May 29, 2017 16:59 |
|
Come on you have to be kidding me you don't have a fridge you can look into from your iphone?
|
# ? May 29, 2017 18:28 |
|
QuarkJets posted:Maybe you're looking in the wrong place, because you should be able to see this trend at basically any of the big hardware stores with a little comparative shopping. Popping over to the Lowes website, here are three fridges that are exactly alike except one's white, one's "easycare" (faux) stainless, and one's actually stainless: When we bought our stuff , the stainless options were either the same or cheaper. The stainless option was in stock. So easy choice. Edit: It seems like the price differences are mostly when you look at top freezers. If you look at bottom freezers, including french doors. The stainless option seems to be the same on the few I've checked right now. Sperg Victorious fucked around with this message at 22:43 on May 29, 2017 |
# ? May 29, 2017 22:38 |
|
Sorry to interrupt appliance chat, but I've got a dumb question. I need a picture hook that will work with a drywall anchor. Something like this: Does anyone know what these are called or where I can buy them?
|
# ? May 30, 2017 03:56 |
|
|
# ? May 9, 2024 01:43 |
|
If you can't find parts locally you can get a similar function by putting a washer on your screw before screwing into the drywall anchor and don't tighten it all the way in. If you want to get fancy you can use a spacer with it.
|
# ? May 30, 2017 04:48 |