|
Darchangel posted:The Phillips screws on my '80 Suzuki Issue #1: they're JIS. Get yourself the right tools for the job.
|
# ? Jun 6, 2018 20:57 |
|
|
# ? Jun 11, 2024 03:11 |
|
I think the cheese-metal carb screws are intentional, tbh. The carbs are made of very soft cast aluminum or zinc, and even a tiny crack will ruin them, so it's better to strip the screw than risk overtorquing and breaking the carburetor body. I think. e: but yes definitely some of the reputation comes from using Philips bits on JIS screws. They are not truly compatible with each other and the difference in shape will exacerbate the Philips' designed-in tendency to cam out and strip.
|
# ? Jun 6, 2018 20:58 |
|
How on earth are you supposed to know which is which?
|
# ? Jun 6, 2018 21:01 |
|
JIS screws have a little dot on the head:
|
# ? Jun 6, 2018 21:04 |
|
That being said, the drivers for either will work with either. You do have to be careful with a phillips driver on a JIS screw, as they tend to chew them up in short order. I actually prefer a JIS tip for phillips head screws because the non-cam out action of the JIS tip gives you a touch more purchase on the screw. Source: fixed Japanese photo printers that exclusively used JIS screws for just a shade shy of a whole decade. Geoj fucked around with this message at 04:40 on Jun 7, 2018 |
# ? Jun 7, 2018 04:38 |
|
Dagen H posted:Dentside Ford trucks had the built-in underhood tool trays. I was one of the first people to buy this Subaru radiator cover with a built-in tool tray: https://www.rallysportdirect.com/part/radiator-shrouds/grm-096005-grimmspeed-radiator-shroud-black Now I wish I had held onto that and put it on my later Subarus. It was a little too small for my ratchet, though.
|
# ? Jun 7, 2018 04:40 |
|
Dave Inc. posted:I know an Åke, and this is just the sort of poo poo he would pull.
|
# ? Jun 7, 2018 06:02 |
|
The Door Frame posted:I've heard Volvo was one of the worst offenders of "bizarro European engineering", but the entire ECU? Not just the fusebox? You should see where GM sticks the ECM on some Corvettes. (... passenger side wheel well)
|
# ? Jun 7, 2018 07:58 |
|
Dagen H posted:JIS screws have a little dot on the head: How do you pronounce 'JIS'? Is it 'jizz'?
|
# ? Jun 7, 2018 08:58 |
|
STR posted:You should see where GM sticks the ECM on some Corvettes. Completely standard on several Mazda models from the late 90s to mid 2000s. Not common, but not super rare either, was the car that was towed in with the dash lit up like a christmas tree because someone had kicked the ECM connector hard enough to knock it loose.
|
# ? Jun 7, 2018 09:14 |
|
Every time I see ECM my brain parses it as electronic countermeasures.
|
# ? Jun 7, 2018 10:40 |
|
Blue Footed Booby posted:Every time I see ECM my brain parses it as electronic countermeasures. I've been so thoroughly programmed by Shadowrun and William Gibson novels that any time someone's talking about the ICE in America, I have to remind myself they're not talking about Intrusion Countermeasure Electronics.
|
# ? Jun 7, 2018 11:07 |
|
I still think the award for worst ECU placement goes to the Isuzu D-Max/Holden Rodeo with the 6VE1 3.5L V6. Heat? Check. Vibration? Check. Premature failure? Check and mate.
|
# ? Jun 7, 2018 11:15 |
|
The Ford 6.0L Powerstroke just asked me to hold its beer for some reason.
|
# ? Jun 7, 2018 11:42 |
|
Dave Inc. posted:It's the actual ECU. It would also appear that in order to change the oil filter cartridge, one also has to go through this rigmarole. Lame.
|
# ? Jun 7, 2018 12:17 |
|
FatCow posted:The Ford 6.0L Powerstroke just asked me to hold its beer for some reason. The 6.0L has said that so many times it has blown through a case of beer.
|
# ? Jun 7, 2018 12:26 |
|
Colostomy Bag posted:The 6.0L has said that so many times it has blown through a case of beer. And it's all pooled in an egr cooler and pissing out an injector.
|
# ? Jun 7, 2018 12:42 |
|
metaxus posted:I still think the award for worst ECU placement goes to the Isuzu D-Max/Holden Rodeo with the 6VE1 3.5L V6. The early chevy 6.5L diesel did something like this. I dunno, early 90's, I think. When they went to the style with the electronically controlled injection pump. They put the controller on the engine and, what would you know, they have issues with all those things! There's actually a factory relocation kit for them...
|
# ? Jun 7, 2018 13:10 |
|
BloodBag posted:It would also appear that in order to change the oil filter cartridge, one also has to go through this rigmarole. Lame. It would make it easier, but you can get access by just removing the boot on the side of the airbox where it connects to the fresh air intake. I always remember hating that thing, though, because you had to push and turn with a bellows duct against a flexible hose to put it back together, so it was like pushing one rope with another rope.
|
# ? Jun 7, 2018 13:47 |
|
Dagen H posted:Issue #1: they're JIS. Get yourself the right tools for the job. Yeah, I know that now. 15 years ago when I first got it and started fixing it, I had no idea JIS existed. Why in the gently caress would you use a fastener head type exclusive to your country for a machine destined for export? Anyway, thanks to the impact driver, I'd wager that they're loving Phillips now. Thanks for reminding me to buy some JIS drivers and bits, though, since I have a whole pile of Mazda RX-7s and the AE86 that undoubtedly use them. Dagen H posted:JIS screws have a little dot on the head: Thanks. Did not know that. Also, apparently, while a Phillips will gently caress up a JIS, you can safely use a JIS driver on a Phillips. Geoj posted:That being said, the drivers for either will work with either. You do have to be careful with a phillips driver on a JIS screw, as they tend to chew them up in short order. Well, there you go. Well, now, this is interesting. This article says that JIS is extinct, quoting Vessel as saying so. Not sure what that's about. Seat Safety Switch posted:I was one of the first people to buy this Subaru radiator cover with a built-in tool tray: My wife's Kia has a pair of smaller pockets like that on the filler panel between the rad and grille. Handy.
|
# ? Jun 7, 2018 18:16 |
|
Allens in old VW/Audis turn to swiss cheese, but the Triple Square and Torx bolts always come out easy.
|
# ? Jun 7, 2018 18:48 |
|
Dagen H posted:JIS screws have a little dot on the head: I had no idea. Are they all like that? Talking about soft bolts, ditto on the old UJMs. I once rounded the bolt head for the oil filter housing on my old Honda CX500 and I ended up saying gently caress it and kept the same oil filter in it for about 2 years before I got around to taking it off. I don't know what the hell they were thinking with those fasteners made out of surplus aluminum foil. I didn't even tighten it hard.
|
# ? Jun 7, 2018 20:53 |
|
Allen heads are the devil's work in anything needing more than minimal torque.
|
# ? Jun 7, 2018 20:58 |
|
spog posted:How do you pronounce 'JIS'? It's "jay-eye-ess" And one of the pieces of equipment I work on (Fuji DEVO) has T7 screws with reduced head depth. They strip so easily, the first instruction in the manual for removing the back cover is "order 20 new screws." InitialDave posted:Allen heads are the devil's work in anything needing more than minimal torque. Head depth matters alot too. Euro manufacturers love that poo poo though. The best is american companies who engineer all their machines to use SAE screws then use an OTS European or Japanese component that has Metric screws, and is secured by metric screws. Jonny Nox fucked around with this message at 21:07 on Jun 7, 2018 |
# ? Jun 7, 2018 21:01 |
|
slidebite posted:I had no idea. Are they all like that? According to wikipedia "Heads are usually identifiable by a single dot or an "X" to one side of the cross slot" For a moment, I was confusing JIS with pozidrive
|
# ? Jun 7, 2018 21:02 |
|
I've never encountered a JIS screw with an "x" on the head, they've all been dots.
|
# ? Jun 7, 2018 22:00 |
|
InitialDave posted:Allen heads are the devil's work in anything needing more than minimal torque. I thought I was the only one, since all of the car shows I watch talk about Allen head screws as though they were just as good, if not better than normal bolts
|
# ? Jun 7, 2018 22:29 |
|
They are everywhere on bicycles and they are terrible.
|
# ? Jun 7, 2018 22:30 |
|
TotalLossBrain posted:They are everywhere on bicycles and they are terrible. There may or may not be an Allen screw on my bike that was converted into a flathead screw with a cutoff wheel after being completely chowdered
|
# ? Jun 7, 2018 22:34 |
|
Shimano used to give out Vessel JIS drivers at Interbike because otherwise apparently no one had any idea about them. Once I got one it became my favorite screwdriver.
|
# ? Jun 7, 2018 22:36 |
|
One benefit of allen head is that you can also use the pound-a-torx-into-it-to-get-it-out method after you completely strip it.
|
# ? Jun 7, 2018 22:40 |
|
The Door Frame posted:There may or may not be an Allen screw on my bike that was converted into a flathead screw with a cutoff wheel after being completely chowdered builds character posted:One benefit of allen head is that you can also use the pound-a-torx-into-it-to-get-it-out method after you completely strip it. Guilty on both counts.
|
# ? Jun 7, 2018 22:40 |
|
Iridium posted:i have no context for this, but knew it belonged here. This is from way the hell back but that looks like a Subaru engine and clutch. I had the exact same thing happen to mine shortly after buying it because the slave cylinder took a poo poo and wasn't releasing all the way. My mechanic showed me a picture that looked almost identical to that one.
|
# ? Jun 7, 2018 22:46 |
|
The Door Frame posted:I thought I was the only one, since all of the car shows I watch talk about Allen head screws as though they were just as good, if not better than normal bolts
|
# ? Jun 7, 2018 22:47 |
|
I have a set of Vessel JIS screwdrivers that I just use on every philips and they work great.
|
# ? Jun 7, 2018 22:48 |
|
InitialDave posted:People mistakenly assume socket-head cap bolts are "better" than regular hex bolts because they're exposed to a lot more cheap poo poo hex bolts. Simple leverage tells you the further out from the centre you apply your force the better. Also I found a new use for 12pt sockets, they hold square nuts nicely. As to why I'm using square nuts? Well I have no excuse there, they're crap.
|
# ? Jun 7, 2018 22:57 |
|
Brigdh posted:According to wikipedia "Heads are usually identifiable by a single dot or an "X" to one side of the cross slot" Poz my Phillips drive.
|
# ? Jun 8, 2018 03:01 |
|
A horrible thought I just had, that will send chills down your spine: External Phillips drive
|
# ? Jun 8, 2018 03:12 |
|
External JIS.
|
# ? Jun 8, 2018 05:45 |
|
|
# ? Jun 11, 2024 03:11 |
|
If you use the right size 'screw', that wouldn't be too bad. Worst crime is building a device that requires screwing at an angle to reach but is designed as a flush mount. Tons of railings do this.
|
# ? Jun 8, 2018 06:11 |