|
Bondematt posted:Any deal I'm going to find that's better than this? I don't think you really need the jigsaw then, you'd probably rather have another battery or charger or something
|
# ? Nov 25, 2018 01:57 |
|
|
# ? Jun 8, 2024 09:28 |
|
Finally got around to dicking with the lathe, a dowel cut-off, and the broken end of a rotten wheelbarrow handle: Getting to not suck at this is going to be habit-forming after I pick up a less foggy mask.
|
# ? Nov 25, 2018 04:58 |
|
whats a good brand/model of orbital palm sander? i've got an old as hell quarter sheet Porter that my dad gave me any reason to get a quarter sheet over a circular pad sander? seems like sheets of paper are cheaper but a minor PITA to swap out sheets compared to the self adhesives
|
# ? Nov 26, 2018 18:04 |
The circular ones are actually random orbit sanders (in general, at least...I'm sure someone makes a non-RO sander in that form). RO sanders are superior, as they have a much lower tendency to make whirls and scratches, making the whole sanding process faster and easier. The pad can swivel freely on an RO sander, letting each burr on the pad follow a random path, instead of just vibrating the whole pad back and forth or around a small orbit, which leads to the same burr tracing the same path over and over. The circular sheets will also have ports for dust collection on them, which is something you won't get cutting up regular sand paper for your clamp-style palm sander. Bad Munki fucked around with this message at 18:11 on Nov 26, 2018 |
|
# ? Nov 26, 2018 18:07 |
|
BraveUlysses posted:whats a good brand/model of orbital palm sander? i've got an old as hell quarter sheet Porter that my dad gave me I've got the Dewalt RO and it's pretty great, but I've always been envious of the pneumatic RO at my hackerspace. That thing fuckin takes material off like a belt sander
|
# ? Nov 26, 2018 18:51 |
|
BraveUlysses posted:whats a good brand/model of orbital palm sander? i've got an old as hell quarter sheet Porter that my dad gave me I like adjustable speed RO sanders. I've put a lot of hours on my Bosch, including refinishing a 20'+ boat and it's still working well. I wouldn't buy one if I wasnt able to adjust the speed. I have replaced the hook and loop pad once. An orbital sheet sander has different uses than a orbital palm and doesnt take off material as well I believe Harry Potter on Ice fucked around with this message at 19:21 on Nov 26, 2018 |
# ? Nov 26, 2018 19:16 |
|
BraveUlysses posted:whats a good brand/model of orbital palm sander? i've got an old as hell quarter sheet Porter that my dad gave me Square sheets of sandpaper are definitely cheaper, but you run through them 3-4 times faster (imo). Also Random Orbital sanders are better for all of the reasons that have already been mentioned. ***RONA DEAL*** Since it's Cyber Monday, Rona if offering 25% off any purchase over $300. This just made the Bosch 12" Glide Mitre Saw ~$30 cheaper than the same one on Amazon, even with Prime and the Bosch 30% holiday promotion, but anything you might be interested in is also subject to the same deal.
|
# ? Nov 26, 2018 20:56 |
|
BraveUlysses posted:whats a good brand/model of orbital palm sander? i've got an old as hell quarter sheet Porter that my dad gave me Pneumatic one’s are the poo poo if you have a big ole compressor and don’t mind listening to it run all the time. They last basically forever even in a production setting.
|
# ? Nov 26, 2018 21:16 |
|
Kaiser Schnitzel posted:I’ve had good luck with Ridgid ones and I’ve used good Bosch and Milwaukee ones too. We used to have a Ryobi one I bought on sale for like $20 and it was great until it died. The Ridgid ones seem to be a bit shorter and have a lower center of gravity which helps with sanding edges or trying to sand inside a drawer opening or something. I don’t really like the DeWalt one I have-it’s fine for sanding paint, but it’s too jerky or something for fine finish sanding. Makita make really nice ones, and the cordless ones reach a full charge in ~15 minutes (and the charger plays a tune when it's done).
|
# ? Nov 27, 2018 00:01 |
|
I'm going to suggest getting a 6" ROS rather than 5", sanding goes a fair bit faster.
|
# ? Nov 27, 2018 01:52 |
|
dyne posted:I'm going to suggest getting a 6" ROS rather than 5", sanding goes a fair bit faster. I would take exception to that notion.
|
# ? Nov 28, 2018 17:59 |
|
I'll bet it feels like you finish the sanding about 16.66666666666% faster!
|
# ? Nov 28, 2018 18:26 |
|
Astonishing Wang posted:I'll bet it feels like you finish the sanding about 16.66666666666% faster! Need a better math nerd here to illustrate why that's wrong (imo) stat!
|
# ? Nov 28, 2018 18:28 |
|
The area of a 6” sander is actually about a third larger than a 5” sander and they really do sand a ton faster. For sanding big flat surfaces a 6” is great to have around, but much less versatile than a 5”. If you just want one, get a 5” imo.
Kaiser Schnitzel fucked around with this message at 19:13 on Nov 28, 2018 |
# ? Nov 28, 2018 19:10 |
|
Kaiser Schnitzel posted:The area of a 6” sander is actually about a third larger than a 5” sander and they really do sand a ton faster. For sanding big flat surfaces a 6” is great to have around, but much less versatile than a 5”. If you just want one, get a 5” imo. Your math is correct as a 5" has approx. 19.62 sq." and a 6" has approx. 28 1/4 sq". However, that presumes that they have a third more HP/amps also, which translates into torque. Generally, they didn't whenever I was A/B'ing them, so the notion of getting more done via extra sanding surface is illusory.
|
# ? Nov 28, 2018 19:18 |
|
Mr. Mambold posted:Your math is correct as a 5" has approx. 19.62 sq." and a 6" has approx. 28 1/4 sq". However, that presumes that they have a third more HP/amps also, which translates into torque. Generally, they didn't whenever I was A/B'ing them, so the notion of getting more done via extra sanding surface is illusory.
|
# ? Nov 28, 2018 19:29 |
|
Kaiser Schnitzel posted:I hadn’t thought about a difference in power, but looking at my sanders, my 5” Ridgid is 3A and 7,000-12,000 rpm (it actually says ‘no’-number of orbits?) and the 6” Ridgid is a two handed beast that’s 4.4A and 4000-10,000 rpm. I guess make sure the motor on a bigger one is stronger-I could see with a pneumatic one how a bigger one might just get bogged down and not actually sand any faster. Sounds like Rigid adjusted appropriately then. I used to lust for the air powered ones too, and then lo, out came the electrics. I've still got a half sheet Makita laying on a shelf and maybe a 1/4 sheet one too. I got a 5" Porter Cable somewhat based on the advice of the tool salesman (without the math, lol), which I've replaced 2 velcro pads on over the decades. It's 3.7 amps, so for equal power conversion, but admittedly faster hogging, I'd need something around 5.6 Amps. At the time, it was the same sander with either size pad as an option.
|
# ? Nov 28, 2018 20:01 |
|
Figured this would be the thread to ask, I ordered some stuff from Harbor Freight. The tracking shows pending status with a city in CA which makes me think they don't warehouse anything much in the US and my order is coming from China. How long does ordering online with HF usually take?
|
# ? Nov 28, 2018 20:49 |
|
It's definitely warehoused somewhere in the states.
|
# ? Nov 28, 2018 22:48 |
|
tangy yet delightful posted:Figured this would be the thread to ask, I ordered some stuff from Harbor Freight. The tracking shows pending status with a city in CA which makes me think they don't warehouse anything much in the US and my order is coming from China. How long does ordering online with HF usually take? Look, you don't get to buy tools that cheap without making some sacrifices. In my experience, they are SLOW. If you didn't pay for faster shipping, you're getting FedEx Ground, or whatever the opposite of priority mail is with USPS.
|
# ? Nov 29, 2018 00:26 |
|
I had a horrible experience with Harbor Freight just recently. I bought a cheapo woodworking bench and had it shipped. About 2 weeks after ordering, it had to be sent back to the original destination during transit due to a label issue. When it got back to the original distribution center, my tracking number disappeared as if it had been delivered, so I called HF and had them re-ship it. Not a big deal, got a new tracking number and we were off to the races again. Fast forward another 2-3 weeks and it finally arrived: - at the wrong address (an Ave nearby with the same number and street name to my Rd. This mistake has happened before, and it's really FedEx's fault so I don't hold this against HF.) - looking like this: As you can see, it looks like they dropped it from a 30 ft height or something. The box was in shambles, pieces of styrofoam were everywhere, and the wood pieces themselves were anywhere from scratched to straight up broken in pieces. A later inventory confirmed about 1/4 of the pieces were missing altogether. Again, keep in mind this is some stranger's stoop that I had to collect this mess from. I called HF and had them ship me a full replacement, and a FedEx pick-up label to ship them the old poo poo in the new box. The replacement arrived about 3 weeks later. The box wasn't in great shape, but comparatively intact. All the pieces are accounted for, but several are broken and require gluing, including the bench top, which has one of the bottoms of its corners snapped off. The kicker is that the two benches aren't even the same model so I can't swap out the pieces. I haven't bothered shipping the old back yet (because gently caress them) nor have I glued the pieces of the new one together because I'm considered driving out to one of their stores, explaining the situation, and seeing what they can do for me. So yeah, F---- would not recommend Harbor Freight.
|
# ? Nov 29, 2018 00:57 |
|
Buying a premade WOODworking bench from harbor freight you say?
|
# ? Nov 29, 2018 01:10 |
|
angryrobots posted:Buying a premade WOODworking bench from harbor freight you say? When I had nothing I bought a premade bench from Home Depot, and then used it to make a real bench. Still have it around, mostly as a junk holder.
|
# ? Nov 29, 2018 20:09 |
|
Tres Burritos posted:When I had nothing I bought a premade bench from Home Depot, and then used it to make a real bench. Still have it around, mostly as a junk holder. Yeah, of course I'd love to make my own bench, but I can't bootstrap my way there when I don't have a flat surface bigger than like 3'x2' to work with right now, hence buying the crap bench from Harbor Freight.
|
# ? Nov 29, 2018 20:20 |
|
If you want to get mad and accuse me of bootstrapping that's fine - I'm sorry you can't see the irony and humor in the situation. And to be helpful, sometimes I have to build stuff in the woods for farm reasons, and have found this plate vise to be very useful for that purpose. It would be a handy addition to an incomplete HF woodworking table.
|
# ? Nov 29, 2018 22:40 |
|
I don’t know what gave you the impression I’m mad, my dude. Bootstrap isn’t a dirty word. Believe me, I wish I could put together a bench with my current set up, but I can’t. Buying a prebuilt woodworking bench IS funny and dumb.
|
# ? Nov 29, 2018 22:57 |
|
Ben Nerevarine posted:Buying a prebuilt woodworking bench IS funny and dumb. I see someone like you and I get my hopes up. Another kindred spirit. Alas though, I'm only to be disappointed once again when I find out you buy your wood instead of growing it yourself. Casual.
|
# ? Nov 29, 2018 23:34 |
|
bobua posted:I see someone like you and I get my hopes up. Another kindred spirit. Alas though, I'm only to be disappointed once again when I find out you buy your wood instead of growing it yourself. One day in the distant future, while I shitpost in my hand-spun underpants woven from the fibers of an exotic bubinga tree I grew myself from a sapling, I will laugh as you are forced by decorum to refer to me not by username, but by my agreed-upon title: The Ina Garten of Woodworking.
|
# ? Nov 29, 2018 23:50 |
|
Lowes or homedepot will probably let you take some cheap rear end pallets for free. Get like 5 of them and two 2x4's at 4 feet. Stack the pallets and then use the 2x4s as a brace with some screws or nails. BAM, instant table to make a better table.
|
# ? Nov 30, 2018 00:12 |
|
I built this poo poo holder in a couple hours and Lowe’s guy cut the plywood for me since I didn’t have my table saw yet. https://www.familyhandyman.com/workshop/workbench/how-to-build-a-workbench-super-simple-50-bench/view-all/ Cost a bit more than $50 by the end of it but it was the right thing to start with and now *slaps roof of work bench* holds so much junk.
|
# ? Nov 30, 2018 01:37 |
|
I built mine in my driveway with only a circular saw, tape measure and a drill. I used 4x4s for the legs and 2x4s for the cross pieces. A used a cut down 4x8 sheet of 3/4 inch plywood for the top. It took a few hours and it was super solid. I used it for 10 years. When I moved, the next tenants paid me $100 to leave it behind. Was it top notch wood working? No, but it was fully functional and didn't shake if I was hammering on it.
|
# ? Nov 30, 2018 02:14 |
|
Want a lift to do car work but the garage isn't tall enough for a two post. Thoughts on this? https://www.costco.com/QuickJack-5%2c000-LB-Capacity-Portable-Car-Lift.product.100460313.html E. Never mind I just realized that the max height is 21 inches. ThirstyBuck fucked around with this message at 04:37 on Nov 30, 2018 |
# ? Nov 30, 2018 04:24 |
|
Those are actually pretty good. But yeah.....the lift isn't very high. It's WAY better than jackstands. Especially if you're doing something like pulling a trans.
|
# ? Nov 30, 2018 05:19 |
|
WTF? I found an expiration date on the spare discs for my Dremel saw I got a few Christmases ago. What fuckery is this?
|
# ? Nov 30, 2018 21:16 |
|
Whatever they are bonded together with probably degrades over time and they go through a lot when spinning. Personally I'd follow something like that (not to the day or week but years for sure) but I understand people make bad decisions when money is involved
|
# ? Dec 1, 2018 00:23 |
|
Important day https://twitter.com/sansculotides/status/1068640832641585152
|
# ? Dec 1, 2018 01:14 |
|
But none of those are pickaxes. They're just picks.
|
# ? Dec 2, 2018 06:37 |
|
My 12" Bosch Glide Mitre saw was just delivered! I'm 3048km and 210 days from getting my hands on it. (I'm living and working in Calgary, but my woodshop is back in Ontario where I spend the summers).
|
# ? Dec 3, 2018 22:00 |
|
Blistex posted:My 12" Bosch Glide Mitre saw was just delivered! I'm 3048km and 210 days from getting my hands on it. Free saw somewhere in Ontario! I kid, that is a sweet saw post pics of the cool stuff you make with it
|
# ? Dec 4, 2018 01:16 |
|
|
# ? Jun 8, 2024 09:28 |
|
So I am about to do a large amount of dirt work to restore some property and fix some flood damage. The problem is I will be solo for most of it. So what is a decent laser transit that can be used solo and doesnt cost thousands of dollars? It needs to have some decent range as I will be marking contour lines that are over 50 yards long and dont want to be constantly resetting it.
|
# ? Dec 5, 2018 21:20 |