|
Jim Silly-Balls posted:This is me irl I'm sure I've mentioned this story before but one of my acquaintances boasted that he could wheelie literally any bike, with a standard bet of one pint at several biker pubs in the Home Counties if anyone could bring him a (road-legal, two-wheeled) bike that he couldn't. I've seen him wheelie old French mopeds (full throttle and full pedaling required to get the torque), full-dress Harleys, and even a shaft-drive BMW (possibly breaking the universe in the process, but that's an old internet joke for another story). Then one of my neighbours decided to really push him and handed over the keys to his 80s Goldwing (the one I know I've mentioned before with the massive sound system he would use to blast Ride of the Valkyries while filtering). Wheelie bloke took it off round the corner and came past the car park of the pub several times with variations on the theme of throttle, clutch and weight failing to get the wheel more than an inch off the ground. He disappeared for a minute or two - long enough for us to believe that he'd fled in shame - before he came past, one foot on the pillion, one on the backrest, with the luggage scraping the ground and the number plate shattered. He explained the technique was to stand on the seat, slam on the brakes, and jump on the back seat while clutching it up, if anyone wants to replicate it (on someone elses bike...) Fair play to him he did offer to replace the scratched up bits but my mate decided he'd keep them to pretend he'd done it, lol.
|
# ? Sep 8, 2019 16:38 |
|
|
# ? May 14, 2024 12:37 |
|
goddamnedtwisto posted:before he came past, one foot on the pillion, one on the backrest, with the luggage scraping the ground and the number plate shattered.
|
# ? Sep 8, 2019 21:20 |
|
goddamnedtwisto posted:I'm sure I've mentioned this story before but one of my acquaintances boasted that he could wheelie literally any bike, with a standard bet of one pint at several biker pubs in the Home Counties if anyone could bring him a (road-legal, two-wheeled) bike that he couldn't. I've seen him wheelie old French mopeds (full throttle and full pedaling required to get the torque), full-dress Harleys, and even a shaft-drive BMW (possibly breaking the universe in the process, but that's an old internet joke for another story). I’m literally that dude. You can wheelie anything with the right setup. tjones posted:As someone who rides a friend's floorboarded Harley when I'm bored and swapping bikes, gently caress floorboards. They serve no good purpose. Agreed on both points. I’m glad whoever bought the bike originally had the good taste to get the pegs and single action shifter. I also took the highway peg floorboards off the front and replaced them with leftover RD350 pegs
|
# ? Sep 8, 2019 22:15 |
|
I replaced the piston on my Husqvarna FC350 this weekend cause it was bogging out at high rpm/high speed and it was blowing some smoke out the butt. The old piston and rings looked alright and not torched and it still smokes a bit and I'm thinking I should've done valve stem seals as well while I was in there Anyone want to tell me it's a terrible idea to ride a bike on a kart track this weekend that has leaky valve stem seals? cause I'm gonna do it.
|
# ? Sep 9, 2019 02:28 |
|
It’s not a terrible idea. Keep it topped up with oil. Leaky valve guid seals are more of a cosmetic annoyance. Real answer: it’s a euro dirt bike. Chances are good it was gonna blow up anyway.
|
# ? Sep 9, 2019 02:34 |
|
It's only annoying because the main symptom is bogging out when you're approaching 100mph at the top of 5th, which is really hard to diagnose and repeat on the street. Abusing a sumo on a full size road track is incredibly fun and probably very bad for the engine.
|
# ? Sep 9, 2019 02:37 |
|
For some stupid reason I got the itch to open up my Nighthawk 750 and bleed the hydraulic tappets (since I'd never seen one, and thought it might clear up a ticking that I am imagining I can hear). I've spent the last day and a half pulling out the camshafts, checking out the rockers, bleeding tappets, cursing at the cam chain and timing marks, freaking out when the engine stopped turning (turns out the cam chain loves to bind up in the bottom end), and finally buttoning it all up and starting the engine with some trepidation. The engine runs fine (but the ticking is still there ). I actually had a reason to be in there to replace the seal on the valve cover, but could have done only that with a lot less blood and angst. I learned a lot and can't say I totally regret the experience. One technical question: I didn't see a way to line up the firing order with the crank rotation (since each cylinder only needs to fire on every other crank rotation). Do the coils just fire on every rotation (that is to say, do they fire an extra spark at the end of the exhaust stroke?) EDIT: I always forget to get pics of these things in progress but enjoy a pic of my camshafts: Ulf fucked around with this message at 04:10 on Sep 9, 2019 |
# ? Sep 9, 2019 04:07 |
Ulf posted:For some stupid reason I got the itch to open up my Nighthawk 750 and bleed the hydraulic tappets (since I'd never seen one, and thought it might clear up a ticking that I am imagining I can hear). That's exactly what they do, when 1 is firing 4 is exhausting so the spark does nothing, and vice versa plus the same for 2-3. It's referred to as a wasted spark system, what with the one spark event per coil going to waste.
|
|
# ? Sep 9, 2019 05:17 |
|
tjones posted:As someone who rides a friend's floorboarded Harley when I'm bored and swapping bikes, gently caress floorboards. They serve no good purpose. The one time I've seen a valid use for them was an acquaintance that had almost lost his leg in a motorcycle accident (he was riding and a sedan ran a red light and t-boned him). They reattached it but he had severely limited flexibility and mobility in that foot. He could press with his leg, but he couldn't lift flex at the ankle. But that's about the only situation I've seen where I thought they made sense.
|
# ? Sep 9, 2019 12:18 |
|
Rex clutch: Fiber plates are within spec and not visibly warped, I don't have a great reference plate to properly check against for warpage Steel plates are mostly very smooth finish, with spots that are visibly matte instead of shiny, but still finger-smooth. The furthest in steel plate is a bit discolored. Basket and hub seem in good condition. There's a bit of a wavy feeling on the surface of the basket grooves that pushes against the clutch plate fingers. Couldn't get the hub nut off even with putting a pipe through the wheel spokes. Should have left it in fifth. The main springs are a couple thou above the rejection spec. They should be closer to a hundred thou above. Getting new springs. The rollers in the thrust bearing are quite worn. Getting a new thrust bearing, pin, and plate. Hopefully that will take care of the gronk.
|
# ? Sep 12, 2019 05:01 |
|
I changed the fork springs and oil on my nx 250(the black one) to make it be a little firmer. Used fork oil smells soo bad. I also lowered the front fender back to stock since we're gonna stud some default dimension front tires for this winter so I don't need the extra room for the tire to clear. Next up is to mount a extra light that turns with the fork like my brother has set up on his red one. Wired into the high beam. We use cyclops 10k h4 bulbs, but the light not turning with the bike is a little annoying in the fall. Supradog fucked around with this message at 07:54 on Sep 13, 2019 |
# ? Sep 13, 2019 07:50 |
|
Going to do a coolant flush this weekend so today I picked up the supplies. Apparently it's a huge time-sink effort if you want to actually do a flush and not just a quick change. Mainly because you have to ride and let the motor cool before you start messing with the cooling system for obvious scalding-prevention reasons. I may change my spark plugs while I'm at it, since I bought replacements a month ago.
|
# ? Sep 13, 2019 12:21 |
|
Martytoof posted:Going to do a coolant flush this weekend so today I picked up the supplies. Apparently it's a huge time-sink effort if you want to actually do a flush and not just a quick change. Mainly because you have to ride and let the motor cool before you start messing with the cooling system for obvious scalding-prevention reasons. Possible foot in mouth here, because I haven't done a coolant flush on a bike, but surely its no different than a car? They have kits where you can take off a radiator hose, hook up the kit, then use a garden hose to flush the entire system. I would think that would save you a significant amount of time. Or Slavy will chime in about one weird trick that will make it a 5 minute job.
|
# ? Sep 13, 2019 16:47 |
Martytoof posted:Going to do a coolant flush this weekend so today I picked up the supplies. Apparently it's a huge time-sink effort if you want to actually do a flush and not just a quick change. Mainly because you have to ride and let the motor cool before you start messing with the cooling system for obvious scalding-prevention reasons. Ex250 right? There's a drain screw on the water pump, it's a 10mm bolt with a visible copper washer. There is also a drain screw on the front of the barrels, behind the exhaust. Drain them when it's dead cold and upright. If what comes out is green and not muddy or rusty looking, don't worry about flushing etc, the drain screws will get 95% of it. Be sure to take the fairing off and drain the overflow reservoir as well. Fill the system to the brim with the bike upright, overfill the reservoir slightly then run it at idle until the radiator level stops going down or it starts to visibly want to overflow and boil up. Give the hoses a bit of a squeeze and stuff to dislodge any trapped air - the ninjette is really good and easy in this respect so don't get too wound up about it. Put the cap on, go for a ride, check reservoir level afterwards. Easy!
|
|
# ? Sep 13, 2019 19:33 |
|
Yep. That sounds way more bearable than the flush. I’m not even sure the bike needs a flush but I don’t trust the PO to have done anything right. I’ll just replace for now and enjoy the month and change I have left to ride. Re: power flush — I’m sure you can power flush but that’s probably way out of my league some kinda jackal fucked around with this message at 01:36 on Sep 14, 2019 |
# ? Sep 14, 2019 01:31 |
Forgot to mention: coolant will loving rocket out of the drain screw the moment you take the rad cap off. Deflect the stream with cardboard or suffer the pissy consequences.
|
|
# ? Sep 14, 2019 01:44 |
|
Don't kink shame me thx.
|
# ? Sep 14, 2019 02:32 |
|
So I sold my 2015 VFR after 35,000km. Seems I dodged a bullet too, looks like the last place I serviced it (repairs after dropping it in the driveway) kinked the breather for the fuel tank. Guy who sold it for me told me the guy they sold it to came back day later complaining of strong fuel smell. Turns out because the breather was blocked, the tank split from the pressure and released a bunch of fuel. Yet another reason why I will avoid getting my bike serviced by anyone but myself unless I have to...
|
# ? Sep 14, 2019 05:26 |
|
loaded it up again (with an incredible amount of weed and even MORE spam) before my next 2500mi trip to nashville
|
# ? Sep 15, 2019 22:56 |
|
right arm posted:loaded it up again (with an incredible amount of weed and even MORE spam) before my next 2500mi trip to nashville hell yeah
|
# ? Sep 16, 2019 06:37 |
|
Got my clutch tool so I popped the hub off. Everything else looks to be in pretty good shape. Because I don't know, though, how do these clutch basket fingers look?
|
# ? Sep 19, 2019 05:28 |
That's fine, barely worn at all. Your problem must lay in the release system, or elsewhere. E: does that basket have springs on the back side?
|
|
# ? Sep 19, 2019 05:59 |
|
Yeah, they're not broken that I remember but I don't think I can remove them the way the basket is constructed There's also a sprung damper in the hub, no spec on spring length there e: Damper springs and basket springs definitely not broken. Everything else looked good. Reassembled the clutch and buttoned it up with new clutch springs and thrust bearing. The gronk is still there. I've done about all I can to that side of the clutch. It's hydraulic-operated so I'll address rebuilding the master and slave cylinder later this year. Also added a 12V/USB port under my seat, just wired right to the battery. Phy fucked around with this message at 18:23 on Sep 20, 2019 |
# ? Sep 19, 2019 06:59 |
|
My 2017 Street Twin has had this really annoying fault where all the warning lights would come on about half the time I made a full lock turn to the right. Bike running perfectly and they all went out after a restart. It’s out of warranty and I’m not the original owner but after fruitlessly searching for what I assume is a wiring fault and reading about a recall this model year had I took it to the local triumph dealer. They have agreed it’s a manufacturing issue and are replacing the whole wiring loom which I’m pretty happy with as I now assume that’s the hidden reason I managed to pick it up cheaply.
|
# ? Sep 20, 2019 18:06 |
|
What are the odds that a British bike would have an electrical issue? (good job on the free wiring harness replacement)
|
# ? Sep 20, 2019 19:23 |
|
Topped off my GL1000s oil with automotive synthetic a while back because I was lazy. Changed the oil back out with the appropriate stuff today. Also did the final drive oil, probably for the first time in it’s very destructive life. I had forgotten about the smell of final drive oil. From my time working on RWD Volvos though, I’ll never ever forget the taste.
|
# ? Sep 21, 2019 18:54 |
|
I've heard that there is some concern about the friction modifiers in automotive oil soaking into your clutch plates and being a problem even after you change it back to the proper kind. Idk. Maybe consider replacing those too if they're not too expensive and your clutch is getting old anyway.
|
# ? Sep 21, 2019 18:57 |
|
Clutch plates on a Goldwing is an engine out job Just throw a little sand in there for extra frictions
|
# ? Sep 21, 2019 19:24 |
|
Yeah if I have to pull the engine... I mean, I’ve done it before on a parts GL1000, I know enough to know I don’t want to have to do it again. 76,000 miles on the original so far though, and a dirty neutral indicator switch making my dash constantly glow green...
|
# ? Sep 22, 2019 00:23 |
|
The Rex, Yesterday: cleaned and waxed the chain and flipped the eccentric tensioner upside down Then put my big hardcases on, strapped my tent to the top and rode out to my usual BC haunt Today: hit the good poo poo (New Denver through to Creston, with a ferry in the middle) and rode back to cowtown. I just barely made the ferry, if I hadn't I'd only be getting in as I post this now. But I did have breakfast on the boat. Never miss a chance to eat on a boat, I say. Also, I met a duck
|
# ? Sep 23, 2019 04:55 |
|
Pretty good weekend. Originally planned the pod lights to turn on with my high beams, and the LED underglow to only be workable off the ACC circuit. Couldn’t crack open my high beam switch, those screws were rusted on. My usual plan for that is to Dremel cut a flat head slot and break the screw or bolt off with the biggest screwdriver I can find. My Dremel remains in Arizona with my ex wife. Ok, go grab my dad’s kit. There’s a post-it inside. “Switch broken, 8-03-2016.” Who tf does this. Well never mind. Pod lights are wired into the ACC circuit now off of a relay, and I’ll come back to it. LEDs still come on whenever, they’re direct off the battery. My Oldwing continues to slowly transform into a spacecraft.
|
# ? Sep 23, 2019 19:09 |
|
I changed the 15T drive sprocket to 16T. On Thursday I'm kicking off a 2200-mile road trip to California and back.
|
# ? Sep 23, 2019 19:55 |
|
Ulf posted:I changed the 15T drive sprocket to 16T. On Thursday I'm kicking off a 2200-mile road trip to California and back. On the Zero or Nighthawk?
|
# ? Sep 24, 2019 04:34 |
|
On the nighthawk. The Zero only has level 2 charging so longer road trips take a bit long (you spend 50% of the time charging), plus there’s a charger gap in the UT/NV/AZ area.
|
# ? Sep 24, 2019 14:13 |
|
Stuck a pair of cheapo wide angle circular rear view mirrors to my regular mirrors so I can see who's on my rear end more clearly, but was feeling kind of blehh so didn't get a chance to try them on the road :[
|
# ? Sep 24, 2019 14:15 |
|
i bought a cheap motorcycle over the weekend from the original owner I started to do some thing to it today oh god, what have i started
|
# ? Sep 25, 2019 04:55 |
|
Withnail posted:i bought a cheap motorcycle over the weekend from the original owner Looks like the front fell off
|
# ? Sep 25, 2019 05:41 |
|
I like it much better.
|
# ? Sep 25, 2019 06:27 |
|
OctaMurk posted:Looks like the front fell off https://youtu.be/3m5qxZm_JqM
|
# ? Sep 25, 2019 06:35 |
|
|
# ? May 14, 2024 12:37 |
|
Revvik posted:
I am extremely appreciative of those Vetter bags. They look cool
|
# ? Sep 25, 2019 18:11 |