|
Properly giggling at the post, Slavvy. Heh.Slavvy posted:They often assume they are the first person to ever encounter a problem and must thus develop a solution from first principles ROFLMAO!
|
# ? May 29, 2021 09:48 |
|
|
# ? Jun 5, 2024 03:19 |
|
Rev. Dr. Moses P. Lester posted:Sorry I missed this until now, what is this bike? A Bantam or something? It is a 1950 Bantam D1. Luckily this bike was restored by my old man who was not an engineer so no stupid hacks. I did notice that the chain adjusters had different threads but had the same nuts yet somehow it had not fallen off.
|
# ? May 29, 2021 13:38 |
|
Slavvy posted:All of this is totally in line with being an engineer. Especially the compulsion to do a weird workaround instead of fixing it the 'boring' way, innovation or no practical experience idk. I've found that when I meet someone who has very strong opinions about areas outside their expertise and is convinced they have it figured out despite being demonstrably wrong, nine times out of ten they're a computer toucher or engineer.
|
# ? May 29, 2021 21:23 |
|
Jury rigged a garage door opener in my cockpit. Bought a cheap garage door opener and flush momentary switch from Amazon and wired the two together. I wouldn’t say it looks OEM but it’s very clean and I can stop rummaging in my pockets to open the garage when I pull into the drive. Not gonna lie, taking a drill to my cockpit plastic was pretty ..
|
# ? May 30, 2021 01:44 |
Luckily at this very instant there are a hundred other ninja 650's being plowed into a ditch or ebay farkled beyond recognition so you're not destroying anything valuable and are in fact better than most owners!
|
|
# ? May 30, 2021 05:01 |
|
MomJeans420 posted:I've found that when I meet someone who has very strong opinions about areas outside their expertise and is convinced they have it figured out despite being demonstrably wrong, nine times out of ten they're a computer toucher or engineer. I've lost count of the number of times I've seen some dunderheaded climate change denialism preceded by "I'm an engineer and". I sometimes wonder if it's a case of having enough skillset in working from first principles to be dangerous, combined with being in a career that doesn't really reward you for questioning your own conclusions early and often. Anyway! I put the wheels back on today. Found out I badly need rear brake pads, replaced the locknut I mangled with a nylock due to not really having a better option readily available, and cleaned and waxed the chain for good measure. Did the bouncy-bouncy thing on the front forks before tightening everything back up, as well as making sure the rear axle pucks were at the same timing.
|
# ? May 30, 2021 06:42 |
|
Phy posted:I've lost count of the number of times I've seen some dunderheaded climate change denialism preceded by "I'm an engineer and". I sometimes wonder if it's a case of having enough skillset in working from first principles to be dangerous, combined with being in a career that doesn't really reward you for questioning your own conclusions early and often. Engineers are to STEM-adjacent fields as nurses are to medicine and biology. Both require a lot of training but an awful lot of it is rote memorisation, both (can) have massive responsibility on them but they're covered as long as they do exactly what it says in the books, and so both often mistake the knowledge they have for intelligence, and tend towards false authority/Dunning Kruger/whatever you want to call this phenomenon. (Of course we all know the *true* genius is the dilettante who quickly reads up Wikipedia on a subject before spouting off with total authority on any given subject rather than just limiting themselves to one field that they're dumb in)
|
# ? May 30, 2021 07:11 |
|
The engineer thing is present in every field that values providing a solution more than anything else, including finding out if anyone wants a solution.
|
# ? May 30, 2021 07:55 |
|
After much loving around trying to get the springs on yesterday, a post-coffee idea hit this morning to do each one separately using a wire coat hanger. Some extra grunt courtesy of my Mom for the 2nd spring and the centrestand is on.
|
# ? May 30, 2021 16:27 |
|
Chris Knight posted:After much loving around trying to get the springs on yesterday, a post-coffee idea hit this morning to do each one separately using a wire coat hanger. Some extra grunt courtesy of my Mom for the 2nd spring and the centrestand is on. Way back when I owned a CB250, it was possible to fit an overseas centerstand to them. On the mailing list (dating myself here), a guy shared a technique that involved shoving dimes or pennies into the spaces in between each coil to lengthen the spring before putting it on.
|
# ? May 30, 2021 16:53 |
|
Slide Hammer posted:Way back when I owned a CB250, it was possible to fit an overseas centerstand to them. On the mailing list (dating myself here), a guy shared a technique that involved shoving dimes or pennies into the spaces in between each coil to lengthen the spring before putting it on. Also at the new thread title
|
# ? May 30, 2021 18:37 |
Chris Knight posted:After much loving around trying to get the springs on yesterday, a post-coffee idea hit this morning to do each one separately using a wire coat hanger. Some extra grunt courtesy of my Mom for the 2nd spring and the centrestand is on. Aftermarket exhausts frequently come with a little pre-shaped coat hanger for the springs so I've got a bunch laying around just for the job, it's super handy. Slide Hammer posted:Way back when I owned a CB250, it was possible to fit an overseas centerstand to them. On the mailing list (dating myself here), a guy shared a technique that involved shoving dimes or pennies into the spaces in between each coil to lengthen the spring before putting it on. This is some psychotic poo poo, I'll bet he was an engineer.
|
|
# ? May 30, 2021 19:31 |
|
I bought a $10 2-pack of spring pullers from Amazon just for stupid bike stuff. I thought it’d be a waste of money as I’d only use once or twice but that $10 has saved me a ton of frustration not just on bikes, but also around the house and car. I’m starting to accumulate a full toolbox drawer of “things I thought I’d only use once but they’re now my favourite thing”.
|
# ? May 30, 2021 19:34 |
|
Please post more examples from that drawer!
|
# ? May 30, 2021 19:58 |
|
Steakandchips posted:Please post more examples from that drawer! Yeah I didn't mean for that to sound like I had some assortment of oddball tools, it's standard stuff just not things I'd expected to use over a standard screwdriver or socket wrench. T-handle wrenches are now my favourite thing and I will use one over a screwdriver every opportunity I get. But also a whole collection of lights. Magnetic lights, lights with legs that I can wrap around things, headlamps. You can never have enough light when working on anything.
|
# ? May 30, 2021 21:21 |
|
Martytoof posted:Yeah I didn't mean for that to sound like I had some assortment of oddball tools, it's standard stuff just not things I'd expected to use over a standard screwdriver or socket wrench. T-handle wrenches are now my favourite thing and I will use one over a screwdriver every opportunity I get. But also a whole collection of lights. Magnetic lights, lights with legs that I can wrap around things, headlamps. You can never have enough light when working on anything. I’ve said it before and I’ll say it again: lighting is the single most important thing in your workspace. It doesn’t matter if you wrench in an empty airplane hangar, if it’s lit like an underground cave, it’s all for nothing.
|
# ? May 30, 2021 22:01 |
Lightin, any kind of table/bench and a clean level floor are the minimum to qualify as non-field-repairs for me.
|
|
# ? May 30, 2021 23:52 |
|
After putting clipons on the Scrambler, with the bar-end mirrors, the stock clutch lever would hit the mirror any time I pulled it in. The weather here is trash this weekend, so I set aside some time yesterday to replace them, assuming it would take up a bit of my afternoon and give me something to do. It took me.. 90 seconds? I assumed I'd have to gently caress with the clutch and brake cables but they're just integrated into the lever housing thing there. There's just a little bolt and a retaining nut keeping the lever in place. Anyway now part of my bike is red so it's not just black and silver.
|
# ? May 31, 2021 02:10 |
|
How do you like the shorties? I learned to ride on them thanks to the PO’s love of eBay parts. Was a little weird to switch back to long levers once I bought a new bike but now I’m not sure I could go back to shorties.
|
# ? May 31, 2021 02:31 |
|
Martytoof posted:How do you like the shorties? I learned to ride on them thanks to the PO’s love of eBay parts. Was a little weird to switch back to long levers once I bought a new bike but now I’m not sure I could go back to shorties. Because of the weather I haven't had a chance to use them yet, but they're basically just in the spots where my fingers go anyway, so it shouldn't be too different. Also when the Scrambler tried to commit suicide and one of them broke, it was basically down to a short lever, and I didn't really notice the difference in using it before replacing it.
|
# ? May 31, 2021 03:56 |
|
Strife posted:After putting clipons on the Scrambler, with the bar-end mirrors, the stock clutch lever would hit the mirror any time I pulled it in. The weather here is trash this weekend, so I set aside some time yesterday to replace them, assuming it would take up a bit of my afternoon and give me something to do. Bikes haven't used brake cables for ages, and in your case the clutch is also hydraulic. The housing is the master cylinder. I've had bad luck with similar levers from eBay (maybe yours are genuine?), the brake lever would stay ever so slightly engaged and that would eventually result in boiling brake fluid.
|
# ? May 31, 2021 08:18 |
Those are the dreaded eBay shitters, I see them every day. Sometimes they work fine, other times they stick the brakes on or drag the clutch or make it impossible to disengage the clutch or get a good cable adjustment. The pivot ratio is always wrong, the fit on the pivot bolt is usually loose. I have them on my bandit and they're fine. My brake and clutch mc don't match so having the 'correct' levers would drive me crazy.
|
|
# ? May 31, 2021 10:04 |
|
Put a new headlight on (again) as part of a general facelift a few weeks ago, and got around to putting decals on today. I'd like a yellow detail panel for the rear eventually. There's a bit of a laundry list building up for this bike but I'm stubbornly waiting until the workshop is finished to do them. No more hunting for nuts and bolts in the gravel thank you very much The subframe on the 650r is notoriously the worst part of the machine and I need to find a way to reinforce it before I do adventure camping in the summer. I also need to rebuild the forks Shelvocke fucked around with this message at 14:22 on May 31, 2021 |
# ? May 31, 2021 11:33 |
|
High Protein posted:Bikes haven't used brake cables for ages, and in your case the clutch is also hydraulic. The housing is the master cylinder. These were seemingly the only ones in stock. They’re the lovely cheap ones but I don’t intend to use them for long. Maybe I’d be better off just grinding my stock ones down.
|
# ? May 31, 2021 14:49 |
|
Changed the oil on the W, and once again I'm thankful I do my own work. Does it take 5 times longer than it would if a professional did it? Sure, but also nothing is stuck or seized and there's no surprises. Besides it's gorgeous weather for just chilling in the back yard and I'm having a good time even if I don't get much done. Low stakes wrenching is good times.
|
# ? May 31, 2021 16:35 |
|
I just ordered some oil for my 650 too. Threw an ez-drain valve on it last year so unless I’m swapping the filter it’s literally five minutes work and the only tool involved in the process is me
|
# ? May 31, 2021 16:46 |
|
After installing the new tires I didn't ride until this morning. They feel a little twitchy, but since I'm not loading them real hard (ie not super worried about the mold release oil thing) I'm kind of assuming it's because I'm going from old squared-off PR2s that I didn't often get past the square on anyway, to a brand-new taller profile tire.
|
# ? May 31, 2021 17:47 |
|
Washed it. Re-rust-proofered it. Went for a 2h long ride, then, on the way back, this happened, while waiting with a bunch of other bikers at the lights, which was cool: https://www.youtube.com/watch?v=Lw7Pn1nos8c TLDW: Biker 1: vroom. Biker 2: vroom. Me: VROOOOM. Biker 1: *thumbs up*
|
# ? May 31, 2021 17:48 |
|
Steakandchips posted:Biker 1: vroom. Everyone else on the street: https://www.youtube.com/watch?v=ylhsbfQTPDQ&t=9s joking, joking, I kid because I love
|
# ? May 31, 2021 17:56 |
|
Renaissance Robot posted:Low stakes wrenching is good times. It really is. Music on. Cold beverage. Good times Martytoof posted:the only tool involved in the process is me I mean. If I didn’t JUST change the title
|
# ? May 31, 2021 18:02 |
|
Martytoof posted:Everyone else on the street: Heh. A good documentary!
|
# ? May 31, 2021 18:14 |
|
Strife posted:Because of the weather I haven't had a chance to use them yet, but they're basically just in the spots where my fingers go anyway, so it shouldn't be too different. Also when the Scrambler tried to commit suicide and one of them broke, it was basically down to a short lever, and I didn't really notice the difference in using it before replacing it. Trip report: they're fine. I don't even notice that they're much shorter than the stock ones. I'm not sure how they'd stick, but I could see that little adjuster doodad getting screwed up. They'll at least tide me over until the Puig ones I want are back in stock.
|
# ? May 31, 2021 21:50 |
|
Done going over the tenere after getting the oil filters delivered yesterday. In one of the bolt holes for the oil filer housing the threads partially stripped out. It's a deep bolt with only threads far in so getting to the threads to refresh them requires removing the RH side crank case cover. While I wait for the proper gasket for the crank cover I just used the remaining bolts and some liquid gasket on the oil filter housing to be sure its not leaking. Found one more PO fuckery Improper use of the lock ring on the H4 lamp, that tab from the bulb that is visible needs to be bent away before I can change the bulb. Did some investigation, I got high/low H4 on left side, right side is H1. Only the british model for 88-91 came with a right side h4 lamp. I doubt I can find that one. The left side has brackets the wrong places so it's not drop in at least. Looks like having dual lights both in high and low mode is a small project. Added switched usb power, gps dock, swapped the main fuse(and as stock, the only fuse, hello 80 electrical setups, single 20 amp fuse) to mini bladed type from old style glass.
|
# ? May 31, 2021 22:53 |
|
Rode the GS, Oldwing and Seca today. My brother took my kids to the zoo so it was on. I've decided the goldwing needs the float levels checked. The high speed bog feels like the bowls getting low, then filling back up as I let off, because it come and goes just that easily. I'll clean the main jet while I'm in there. The Seca starting circuit got hosed when I removed the tank a few months ago so I'm just shorting the solenoid with a pair of pliers to get it going. Whatever I did when I pulled the carb rack ruined what little idle it had, so I guess it's time to play "find the air leak" again. I've had the bike so long that I am my own PO as of now.
|
# ? Jun 1, 2021 09:09 |
AnnoyBot posted:Rode the GS, Oldwing and Seca today. My brother took my kids to the zoo so it was on. Sounds like a failing fuel pump tbh.
|
|
# ? Jun 1, 2021 20:20 |
|
Slavvy posted:Sounds like a failing fuel pump tbh. I installed an electric pump a month ago. The issue did not change.
|
# ? Jun 1, 2021 20:47 |
Interesting. It doesn't leave much beyond the floats. It would be weird for all of them to be low but PO's I guess. Or you have a delivery problem to the pump itself maybe?
|
|
# ? Jun 1, 2021 20:52 |
|
is there a kinked hose anywhere like coming off the fuel pump?
|
# ? Jun 1, 2021 20:59 |
|
Clogged fuel filter?
|
# ? Jun 1, 2021 20:59 |
|
|
# ? Jun 5, 2024 03:19 |
|
I had a load of pain in my left wrist last time I took the bike out so finally bothered changing the angle of the lever to a more natural angle. Literally a 1-minute job, why didn't I do that before.
|
# ? Jun 1, 2021 23:01 |