|
slave to my cravings posted:What are the white boards connected to on the inside? Floor joists? They're probably the remains of the previous deck that was properly attached to the house.
|
# ? Jun 4, 2021 17:33 |
|
|
# ? May 27, 2024 23:07 |
|
Yeah. Between the transience, Hutterite colonies, and legacy of make-do rural life, we're DIY/cash job central.
|
# ? Jun 4, 2021 17:45 |
|
Can I just drill my new doorbell into the vinyl siding? I don't need a special bracket or anything? It's this little guy here:
|
# ? Jun 4, 2021 17:47 |
|
Vintersorg posted:Can I just drill my new doorbell into the vinyl siding? I don't need a special bracket or anything? It's this little guy here: Looks like you can just stick it on the siding with the double sided tape.
|
# ? Jun 4, 2021 17:51 |
|
Yeah, I might just do that and see how it goes. The builder had put a hole thru the siding for doorbell wires but I don't need them. So covering it up with this. Hope it holds up in the -30C winters!
|
# ? Jun 4, 2021 17:52 |
|
just another posted:It's as bad as you'd expect: Groverdeck
|
# ? Jun 4, 2021 19:07 |
|
just another posted:It's as bad as you'd expect:
|
# ? Jun 4, 2021 19:44 |
|
just another posted:
What is holding the double deck beams onto the posts? Prayers? Maybe I'm not seeing it, but there should be a bracket, not a couple toe nails. edit: The more I look at those pictures, the more my heart rate increases. That deck isn't safe at all, and it looks high enough to seriously hurt somebody; don't use it. B-Nasty fucked around with this message at 20:15 on Jun 4, 2021 |
# ? Jun 4, 2021 20:07 |
|
Well I probably shouldn't pile on this very sturdy deck but I'm curious did your home inspector put anything in their report about it?
|
# ? Jun 4, 2021 21:06 |
|
just another posted:It's as bad as you'd expect: holy poo poo
|
# ? Jun 4, 2021 21:45 |
|
Vintersorg posted:Can I just drill my new doorbell into the vinyl siding? I don't need a special bracket or anything? It's this little guy here: These things weigh essentially nothing, so you don't need to try to hit a stud or anything like that. Personally I wouldn't trust the adhesive to hold up to season changes, so I'd just drill the screws right into the vinyl siding and call it good. Worked well enough for our Ring doorbell. Also that deck is concerning, definitely proceed with caution and get the corners reasonably secured before you venture fully underneath with tools.
|
# ? Jun 4, 2021 22:00 |
|
tangy yet delightful posted:Well I probably shouldn't pile on this very sturdy deck but I'm curious did your home inspector put anything in their report about it? Somewhat. We talked about the posts during the walkthrough and he pointed out how the current deck was secured to the remnants of the old deck and not to the ledger itself. In the body of the written report, the greater concern was the wobbly railings on the stairs, and how the deck wasn't built with a step up into the building and how that could lead to water intrusion. He had a better bedside manner than you lot.
|
# ? Jun 4, 2021 22:02 |
|
just another posted:Somewhat. We talked about the posts during the walkthrough and he pointed out how the current deck was secured to the remnants of the old deck and not to the ledger itself. In the body of the written report, the greater concern was the wobbly railings on the stairs, and how the deck wasn't built with a step up into the building and how that could lead to water intrusion. He was also missing the forest for the trees. Seriously, your deck is held onto the remnants of an existing deck with what exactly? A few screws or nails? I wouldn't consider putting people on a "structure" like that. Google "deck collapse" if you want some motivation on doing it right.
|
# ? Jun 4, 2021 22:07 |
|
Maybe the scale looks funny in the pic, but I thought it was only about 3-4' off the ground. Not that you want any deck to collapse, but it seems like you'd get a lot fewer fatalities.
|
# ? Jun 4, 2021 22:12 |
|
The posts are 3 feet yeah, so broken necks but not fatalities.
|
# ? Jun 4, 2021 22:36 |
|
Until you fall thru a post and a stray nail eviscerates you.
|
# ? Jun 4, 2021 22:58 |
|
Vintersorg posted:Until you fall thru a post and a stray nail eviscerates you. And the grill lands on you and lights everything on fire.
|
# ? Jun 4, 2021 23:18 |
|
Turns out goons are deck hypochondriacs too! OP use at your own risk etc etc and I wouldn't have a party on it and I would replace it sooner rather than later, but it doesn't look like it's gonna collapse tomorrow or anything. If the posts holding it up get more out of plumb, that means something is moving and the risk that something bad happens soon goes up fast. E: to be clear, everyone else is not wrong and your deck was not built at all correctly and is potentially dangerous, but I don't think (in my completely unprofessional, not a structural engineer, not a contractor, just sort of a jakeleg framer opinion) it's gonna collapse tomorrow or next month or probably next year with 4 people and a grill on it. Kaiser Schnitzel fucked around with this message at 23:43 on Jun 4, 2021 |
# ? Jun 4, 2021 23:40 |
|
Kaiser Schnitzel posted:Turns out goons are deck hypochondriacs too! This is how you get a free body diagram drawn at you.
|
# ? Jun 4, 2021 23:48 |
|
Look at this guy underestimating the weight of an average goon
|
# ? Jun 4, 2021 23:54 |
|
Just cover the exterior of the deck with lattice and be the Previous Owner you know you can be. (this is a joke, pls fix your deck)
|
# ? Jun 4, 2021 23:54 |
|
Kaiser Schnitzel posted:Turns out goons are deck hypochondriacs too! Without seeing how that thing is actually fastened to the ledger I wouldn't be willing to to as far as "4 people and a grill." I was not being excessive when I said that messing with jacking it up to replace the existing posts should not be done until that part is sorted. The only "solution" here, outside of the correct one (tearing it down), is to convert it to a free-standing deck as best as possible. And that needs to start at the ledger, not the "outside" posts. (why is that thing cantilevered? WHY?)
|
# ? Jun 5, 2021 00:09 |
|
And the blades of grass harden in a miraculous moment and impale your body as your fall - dropping all your fresh squeezed lemonade.
|
# ? Jun 5, 2021 00:37 |
|
Right, so new plan is: 1. Carriage bolts through the joists that connect to the joists that connect to the ledger 2. New posts and beam maybe a foot out from the house using deck blocks for footers 3. Straighten out (and maybe move) the posts and beam that have gone out of alignment (+ add post caps) 4. Add joist hangers 5. Disconnect the deck from the ledger altogether? With 3' posts, a floating deck would be to code in my area if it had a 18"x18"x3" pad beneath each post.
|
# ? Jun 5, 2021 00:39 |
|
just another posted:Right, so new plan is: No on 5. There is no way to make that a proper free standing deck unless you're gonna sink sonotubes and concrete, possibly not even then. Those carriage bolts in #1 are to keep it from pulling away from/smashing into the house. The posts near them are to take load off of the wholly inadequate lag bolts/amount of overlap so they don't have to carry full weight. I'd say get an engineer to give you an opinion but they would take one look at that, shove their fingers in the ears, close their eyes and start shouting "I CANT HEAR YOU I CAN SEE YOU" as they run to their car where they will bock your phone number and email.
|
# ? Jun 5, 2021 01:47 |
|
just another posted:Right, so new plan is: Anyway, call your insurance agent and ask some serious questions about the liability part of your policy and pretend you never posted questions on the internet where you thought your deck might be unsafe.
|
# ? Jun 5, 2021 02:37 |
|
Maybe it's a dumb question but if this is the requirement for the foundation of a freestanding deck in my area: Why couldn't the existing structure be retrofitted with the appropriate number of posts and cross-bracing?
|
# ? Jun 5, 2021 02:59 |
|
just another posted:Why couldn't the existing structure be retrofitted with the appropriate number of posts and cross-bracing? Because it's built so lovely that no doubt those aren't it's only deficiencies. You could go track them all down and try to add the appropriate hangers, fasteners, spacing, etc but at that point you're better off carefully disassembling it to save the lumber and starting over from scratch. You can't shine poo poo.
|
# ? Jun 5, 2021 03:02 |
|
Fair enough. I'll do my best to make it stable and then strategically avoid buying patio furniture until it's rebuilt.
|
# ? Jun 5, 2021 03:05 |
|
just another posted:Right, so new plan is: 1a: remove the vinyl siding from where the ledger should be, and make sure it's actually there and in good condition.
|
# ? Jun 5, 2021 18:42 |
|
Yay toilet won't fill, let's unbolt it from the floor, pull it away from the wall so we can isolate the water and check the washer in the full valve. Oh it's glued to the wall with silicone? Right, fish a hacksaw blade behind it to cut the silicone. Oh the floor bolts are spinning? Right what else is holding it down? Oh more silicone, okay we know how to deal with that, let's pull it away from the wall and isolate it. There's no isolation valve and the DIY store closes in 15 minutes? gently caress it, job for tomorrow. I hate the man who plumbed this house. As there's an identical copy of this toilet upstairs I'll pick up 2 of everything tomorrow morning. loving houses man.
|
# ? Jun 5, 2021 19:25 |
|
Is there a trick to getting undermount sinks out? Current basin cracked and I have a replacement ready to go, I just can't get them old one out. I'm having a bitch of a time getting thru the adhesive so I can drop the basin.
|
# ? Jun 5, 2021 20:49 |
|
Welcome to the house of glue. Everything is built with glue. Bring more glue.
|
# ? Jun 6, 2021 00:05 |
|
Sirotan posted:Anybody have a sofa from Article? I've had an Ikea sofa for about 2.5 months now and I've come to the conclusion that it's really just not comfortable and I'm probably gonna return it. I'm not keen on buying a sofa I haven't put my butt in first, but what is your budget, what size do you want and fabric or leather? I find article's prices to be low enough where there has to be some corner cutting somewhere. I looked at a random fabric sofa which was 1199 and claimed to have 100K Martindale rubs (not sure why it says "rubs" instead of "double rubs"), but in either case that's an insane amount. You would only see 100K in like, a super busy airport or something. I would expect a sofa at that price point to be more like 10-20K. It was 57% viscose and I've never seen that on a sofa (only rugs) so I'm not sure if it's a good fabric for that kind of item or not. I would just go to a room and board first if they have one in your area. For a standard 83" sofa, I expect to see 1800+ for something really high quality if fabric, and probably 3000+ for leather. Find the firmness and seat depth that is best for you. actionjackson fucked around with this message at 04:48 on Jun 6, 2021 |
# ? Jun 6, 2021 04:43 |
|
Motronic posted:You can't shine poo poo. that porch doesn't sound savable, but let's not be too hasty about what's possible with a turd https://www.youtube.com/watch?v=yiJ9fy1qSFI
|
# ? Jun 6, 2021 07:24 |
|
Sirotan posted:Gonna have to rent a drat van to return this thing and it feels a little lovely even though Ikea does accept returns of used furniture. I spent forever researching sofas the first time around so now I don't even know where to start. Article sofas are a complete piece of garbage and the material will wear out within 2 years of use- they do cost cutting everywhere. What price range and material are you looking at for a sofa, between 2000-5000? Anything less then just go to Costco.
|
# ? Jun 6, 2021 09:59 |
|
Just returned my Ikea sofa yesterday and am probably going with something from Crate & Barrel since they have a store near me and I got to sit on a bunch yesterday to test them out. C&B and Article seem to be the only places that don't have overwhelmingly terrible reviews and while the Article return policy is pretty good I still don't want to drop $2k+ on something I haven't even sat on.
|
# ? Jun 6, 2021 11:39 |
|
Hey goons it has been a while. Things continue to change and evolve here in Vermont. Yes, I said "here in Vermont" because we have officially moved up here. The house sale in PA went well and sold right about where I calculated it would back in the Fall and the money hit our bank account on Tuesday. HUGE relief. The packing and coordinating to make that all happen, while working full time until the day before loading the moving truck, was possibly the most stressful prolonged period of my life from a project planning perspective. Last weekend, the biggest remaining wad of stress was driving the 22' Penske truck (loaded by pro movers on Friday) up to Vermont in the driving rain but I got it done. I hired two locals based on an ad I put out on a local website (Front Porch Forum) and they helped me unload last Sunday and, before we knew it, the move was done. I felt like sleeping for days afterwards. So we have had a week to recover and the builders have been hard at work. On the roof, they installed snow-stoppers (see goons?! I listened. We even found a place that makes these one town over). They haven't done the snow-stoppers on the south roof yet because the solar installation has to happen. Under the porch and all of the soffits were clad in shou sugi ban Tamarack and I think they look super rad. Another team of subs is working on the dry-wall install inside. This picture is about a week old. They have all of the dry-wall put up now and are taping and mudding the whole thing. That should take another week or two and then the paint will go on all walls and the floors get finished. There is no finish on the ash hardwood upstairs and just one coat on the concrete on the first floor but all of the floors are covered right now to keep them safe. The black siding looks great. Here is the east wall which has all of the base covering on it and is awaiting all of the black metal window trim. Here is the south wall which is where the shou sugi ban meets the metal and I think it looks pretty stunning. The electrical has been run to all parts of the house and is awaiting painting so that the light fixtures can get installed. The CAT-6 has been run everywhere too and, on a good internet note, the cable company said they are ready to install our fiber sometime this month. That eliminates another big worry. I bought Starlink as a backup since internet is so essential for my wife's work, but the results have been super spotty. If a Starlink dish gets so much as side-eye from a tree, it stops working and there are a lot of trees around our property. Finding a totally clear spot is difficult. If the fiber happens, it will take most of that worry off the table. The conduit is run, the wire is one pole down the street. The tractor has been ordered but there is now a 3-4 MONTH lead time from Kubota. I ordered it last month so hopefully that timing works out perfectly. Next steps: - Finish drywall taping, mudding and sanding. - Finsih exterior siding and window metal fitting - Painting - Floor finishes - Installation of cabinetry - Lighting - Plaster on fireplace surround - Lots of other stuff -- solar install, grading and landscaping etc The journey continues, but at least I can bug my builder 3x a day about stuff since we are just 4 minutes away.
|
# ? Jun 6, 2021 14:08 |
|
Sirotan posted:Just returned my Ikea sofa yesterday and am probably going with something from Crate & Barrel since they have a store near me and I got to sit on a bunch yesterday to test them out. C&B and Article seem to be the only places that don't have overwhelmingly terrible reviews and while the Article return policy is pretty good I still don't want to drop $2k+ on something I haven't even sat on. My wife picked out an article sofa 18 months ago and I’m super unimpressed. The cushions don’t hold their shape, and we had to sew Velcro onto them so they’d stop sliding off the couch under normal use. The fabric pills like crazy and we constantly get poked by feathers sticking through.
|
# ? Jun 6, 2021 14:29 |
|
|
# ? May 27, 2024 23:07 |
|
Sirotan posted:Just returned my Ikea sofa yesterday and am probably going with something from Crate & Barrel since they have a store near me and I got to sit on a bunch yesterday to test them out. C&B and Article seem to be the only places that don't have overwhelmingly terrible reviews and while the Article return policy is pretty good I still don't want to drop $2k+ on something I haven't even sat on. Have you looked at DWR? Pricey, but they have the best couches that I’ve sat on
|
# ? Jun 6, 2021 14:40 |