|
Motronic posted:I pretty much started with that and failed 3 or 4 times until I came back to it and realized that if I got the die grinder in there and flattened the top of the bolt off I'd have a much better chance of a nut staying welded on. Worked the first time. That looks so much better than dealing with SAI on a goddamned DII
|
# ? Aug 26, 2022 21:11 |
|
|
# ? Jun 4, 2024 00:00 |
|
cursedshitbox posted:That looks so much better than dealing with SAI on a goddamned DII Can confirm. At least it's just one tube per head on the Cayenne. gently caress DII SAI forever. It's, to no ones surprise, the very worst SAI implementation anyone ever came up with.
|
# ? Aug 26, 2022 21:15 |
|
Been chasing my tail trying to figure out random loss of power on my car. Went so far as to watch fuel pump duty cycle, fuel pressure, etc. It felt like it was either yanking timing or leaning out, but I couldn't find much wrong. It just falls over at random when trying to pass people on the highway, sometimes surges slightly while cruising. Cried uncle and had Marty (of Marty Tune fame) do some remote diagnostics on it (laptop + tuner + hotspot). The SCT tuner has a far faster refresh rate than the no name OBD2 bluetooth adapter I was using with FORScan Lite. Basically saw it going a little lean, also noted the duty cycle for the fuel pump is considerably higher than it should be. His suggestions were an OEM Motorcraft fuel filter (which, surprisingly, Advance Auto carries for only a couple of bucks more than the Carquest brand filter, and has it in stock), new OEM fuel pump, and since I'm at that point anyway, NGK 4177 plugs (1 heat range cooler than stock - makes sense, as his tune is a bit more aggressive with timing - I'm running the stock part number Motorcraft plugs right now). dissss posted:TIL the generation 1 Leaf has polystyrene panels underneath the footwell carpets which are just perfect for trapping large amounts of water. Trying to chase down the leak is giving me flashbacks to my old 1990 Integra which I could never get to stay dry in rainy weather. Tail light gaskets and cowl on the teg, right? With a side of sunroof drains? I was still able to get the gaskets new when I had my 91, but that was forever ago (and they were special order even back then).
|
# ? Aug 27, 2022 16:41 |
|
STR posted:Tail light gaskets and cowl on the teg, right? With a side of sunroof drains? Yes, yes and yes. Also the trunk seal (was a sedan and water would pool in the corners by the rear window if you parked facing downhill) and around where the rear spoiler was bolted onto the trunk lid. This was 2001ish so parts weren't an issue yet but I never managed to sort out the sunroof because the metal tray was rusted out around where the rear drains connected to it and I couldn't see any way of getting it out without removing the front or rear glass.
|
# ? Aug 27, 2022 20:06 |
|
Oof, yeah, rust isn't an issue I had to deal with. Mine was originally a GA car, bought it from a friend in the Atlanta area and he drove it out to TX for me (and had my 96 Civic with a blown engine shipped back). Mine was a hatch, had it from 02-03. I never did get the goddamned cowl to stop making waterfalls happen from under the passenger side dash, but I got the sunroof draining properly and the taillights sealed up. I even got all the buttons and lights working on the climate control!
|
# ? Aug 28, 2022 00:37 |
|
The plastic screws that secured the plastic cowl cover to the body of the car had individual plastic condom things that would leak when they aged. Easy enough to replace but the parts were a couple of dollars each from Honda and took some time to arrive. I really wouldn't want to be owning a car that old nowadays because I doubt those sort of parts are still available.
|
# ? Aug 28, 2022 01:08 |
|
Replaced the super worn out sun visors in the EM1 and brought the interior up from a 9.5/10 to a 10/10. Next week, “the spot” gets fixed and then it’s done!
|
# ? Aug 29, 2022 22:34 |
|
I replaced the front turn signal bulbs in my 239K mile 1993 Toyota Pickup. I think these might have been original. They said KOITO MADE IN JAPAN on the base.
|
# ? Aug 30, 2022 15:46 |
|
PBCrunch posted:I replaced the front turn signal bulbs in my 239K mile 1993 Toyota Pickup. I think these might have been original. They said KOITO MADE IN JAPAN on the base. I purchased my 2000 civic Si from the original owner a couple of weeks ago and he told me no bulbs have been replaced on the car other than the bulb for the fog light button on the dash. In 22 years not even a headlight has blown out somehow. I should stock up on every number bulb for the upcoming bulbpocalypse.
|
# ? Aug 30, 2022 16:03 |
|
PBCrunch posted:I replaced the front turn signal bulbs in my 239K mile 1993 Toyota Pickup. I think these might have been original. They said KOITO MADE IN JAPAN on the base. Most likely original. I think there's still a smattering of Koito bulbs in my '79 RX-7. I still have the original Koito non-Halogen headlights stored from when I installed Halogens back in 199X. They clearly didn't sign on to the GE lightbulb conspiracy.
|
# ? Aug 30, 2022 19:24 |
|
Forgot to put a grommit back when I was running wires for AFR and Boost so it was absolutley pouring water into the car in the front passenger footwell. Had to cut then stack a pair of them then RTV'd them in place. Once it cures it goes back together.
|
# ? Aug 31, 2022 02:26 |
|
Its not quite as old as some of y'all's stuff but my almost 14 year old Corolla has had the headlight bulbs replaced (with HIR bulbs) and has gone through several pairs over the years, but other than that I've only replaced one brake light bulb and that was.......3 years ago? Everything else, turn signals, other brake/tail light, all original.
|
# ? Aug 31, 2022 14:18 |
|
I put Bosch Icon wipers on the Accord three years ago and they still work shockingly well, especially given high exposure to the Texas sun and lots of dry weather in general. Never had wipers last anywhere this long without getting brittle. They're only just now getting a little streaky. edit: the Integra's OE bulbs also lasted a freakishly long time. IIRC I only had to replace them when I got to Texas, so like nine years? Not bad given I usually keep them on any time I'm driving because hoooooooooooly poo poo people do not see small black coupes Panty Saluter fucked around with this message at 18:41 on Aug 31, 2022 |
# ? Aug 31, 2022 18:37 |
|
Brake job on the EM1 Old gross poo poo; rear pads were new but the rotors were pretty crusty. The front rotors were extra crusty and the pads were low. New hot poo poo. Rock Auto “Z23” kit with carbon ceramic pads
|
# ? Aug 31, 2022 23:12 |
|
Nothing as demoralizing than working on something for 3-4 hours, fixing the issue (including testing it several times), and then have it gently caress up as you were wrapping up. Fuuuuuuuuck you something van door cable. Now the door is stuck open as a bonus since the cable didn't snap but has now bound up the pulley mechanism. It'll be faster the next time, at least.
|
# ? Sep 2, 2022 17:37 |
|
Suburban Dad posted:It'll be faster the next time, at least. Yeah, you know what tools, sizes etc you need. No going to the tool box 15 times because you got the wrong poo poo.
|
# ? Sep 2, 2022 20:15 |
|
Upol raptor liner. Started at 10ish and done at 4:30. I'm ready for a goddamn beer. Remove everything, clean everything, start masking, scuff everything, mask the rest of the way and tent the whole truck, clean it all again, spray, wait, spray again, strip the masking off and admire. There's more prep than a drat pride parade. The wire lined masking tape is awesome, the lines are very crisp. Edit, pay no attention to the goober in the reflection.
|
# ? Sep 3, 2022 23:43 |
|
so how do you clean up that kind of bed liner when you inevitably get it oily from car parts? painted metal and those plastic liners both scrub up pretty good, but idk about that texture
|
# ? Sep 4, 2022 00:08 |
|
StormDrain posted:Upol raptor liner. Started at 10ish and done at 4:30. Prep for any sort of paint/coating is the bit that takes the longest. It's also the bit which sets you apart from lazy fuckers who have a lovely looking and no doubt inferior quality finish which will chip and fall off a LOT sooner. Looks good, you can be proud of that.
|
# ? Sep 4, 2022 00:55 |
|
Looks drat good - I’d say that was 6 hours well spent
|
# ? Sep 4, 2022 02:07 |
|
Raluek posted:so how do you clean up that kind of bed liner when you inevitably get it oily from car parts? painted metal and those plastic liners both scrub up pretty good, but idk about that texture We will see. Some spots where I sprayed too close are glossy, everywhere else got a pretty even texture because I fogged it from about 4' which gives it the nice dull coat. If it was glossier I'm sure it would clean easier. If it gets nasty and oily I'll live, if in a few years I could clean it up and coat it again. The whole kit was about $120. I'd prep it next time with a abrasive brush wheel thing. StormDrain fucked around with this message at 02:18 on Sep 4, 2022 |
# ? Sep 4, 2022 02:16 |
|
It looks nice, the prep work was worth it. Probably why it costs so much to get someone else to do it.
|
# ? Sep 4, 2022 02:46 |
|
That looks fantastic. Replaced a cheap fuel pump with a slightly less cheap fuel pump No more fuel starvation issue!
|
# ? Sep 4, 2022 04:45 |
|
StormDrain posted:We will see. Some spots where I sprayed too close are glossy, everywhere else got a pretty even texture because I fogged it from about 4' which gives it the nice dull coat. If it was glossier I'm sure it would clean easier. If it gets nasty and oily I'll live, if in a few years I could clean it up and coat it again. The whole kit was about $120. I'd prep it next time with a abrasive brush wheel thing. We did our Jeep's interior and it had similar gloss in the high areas. Once it cooks a few days in the sun, it completely evened out. It's held up well and I'm planning on using it on my trucks bumpers.
|
# ? Sep 4, 2022 04:53 |
|
I put some coilovers on my Boobaru...
|
# ? Sep 4, 2022 04:57 |
|
Looks nice! Did you get fired already?
|
# ? Sep 4, 2022 09:17 |
|
mobby_6kl posted:Looks nice! Did you get fired already? Feels like I'm missing some context here
|
# ? Sep 4, 2022 14:52 |
|
StormDrain posted:There's more prep than a drat pride parade.
|
# ? Sep 4, 2022 15:27 |
|
Suburban Dad posted:Feels like I'm missing some context here Grumbletron 4000 posted:
|
# ? Sep 4, 2022 17:54 |
|
What I thought was going to be a feeling of accomplishment ended up being a sad realization I'm going to have to replace the other one too.
|
# ? Sep 5, 2022 15:52 |
|
Got laughed at by the mechanic when I dropped my Sonata with a caved in drivers side off for an oil change. Ain't my fault the wait for the body shop was nearly three months buddy. They're also supposed to be checking out what's causing a nasty rattle under boost in 4th and higher gears but predictably the car is not cooperating and is running dead silent today.
|
# ? Sep 5, 2022 22:28 |
|
Installed a rear sway bar on the F56 MINI yesterday. Having access to a lift made things so much easier. I had to lower the rear subframe to snake the old bar out and new one in, but it was fairly straightforward. It definitely works as advertised, the car rotates through the corners a lot better now, even though its on the softest setting. And I'm just no noticing the missing bolt on the bumper. I wonder if it never made it on at the factory because the rear bumper has never been off the car.
|
# ? Sep 5, 2022 23:50 |
|
Dropped the EM1 to get “the spot” fixed. The body shop says it will be done later this week; updated pics to come.
|
# ? Sep 6, 2022 20:32 |
|
Imperador do Brasil posted:
They're going to keep it parked inside right
|
# ? Sep 6, 2022 20:53 |
|
opengl128 posted:They're going to keep it parked inside right It was inside the shop before I left the parking lot, but who’s to say after they’re done? I’m away for work the next two days but I might have my wife pick it up and leave her car sit there until I get back if they finish it before then.
|
# ? Sep 6, 2022 21:12 |
|
https://imgur.com/a/CGNFIYr Loading up the trailer. Headed to Bowling Green tomorrow morning for LSFest. Going to run IN Rumble Index (hoping to Index around 11.00). Hoping ghr rain holds off this year. Hopefully my cousin can get a hood made for next year.
|
# ? Sep 8, 2022 02:27 |
|
mobby_6kl posted:Looks nice! Did you get fired already? Nope. Not a peep from HR. Everyone thought the boob chicken was funny so nobody actually complained even when I parked it right next to the office door. I'm still driving around with those big tits on my hood. I'm betting that if I draw a boob cock with a massive set of hooters draped over a hard rear end dick with some pendulous balls involved that'll get some attention. Standby for that update. In the meantime I got a junkyard trunk with a stock spoiler. Still enjoying the hell out of the look from the coilovers... The ride is incredibly good considering how low it is. Gonna have to either roll the front fenders or bring it up a little though since it's rubbing like mad. Ripping the poo poo out of the tires ☹️
|
# ? Sep 8, 2022 10:09 |
|
I like those wheels. Speaking of Subarus, the rear of my '03 Outback is *really* soft. I replaced all four corners when I got it a few years ago with name-brand quick struts, hoping that would stiffen it up a bit, but that didn't really make much of a change aside from the better bounce control from the new struts. Did Subaru just use the lighter springs from the Legacy sedan and not account for the additional weight of the rear end end of the wagon or did they intentionally make it soft as poo poo? Ride height is fine. Does anyone make stiffer springs for the Outback? I don't need a lift (yet...) just a higher spring rate in the rear. edit: it's also possible that the quick struts I got don't make any distinction between sedan and wagon. Darchangel fucked around with this message at 21:12 on Sep 8, 2022 |
# ? Sep 8, 2022 21:01 |
|
sounds like a job for H&R Spinebreakers
|
# ? Sep 8, 2022 21:37 |
|
|
# ? Jun 4, 2024 00:00 |
|
Answering my own question, Rallitek in Oregon has 355 lb/in springs in 0.4" and 1" lift, which claim to be 18-20% and 40-45% stiffer than stock, respectively. Also stiffer front springs in 0"-1" lift, but I'm mainly after the rears. Though... wouldn't taller springs of the same rate be less stiff?
|
# ? Sep 8, 2022 21:48 |