|
mobby_6kl posted:Ok what if... I just make the engine run backwards? You'd need new camshafts, some loving around with the ECU and starter motor, on older engines it's doable I think but on a 23 model it seems impractical.
|
# ? Apr 5, 2023 16:11 |
|
|
# ? Jun 4, 2024 17:03 |
|
mobby_6kl posted:
I actually used that trick to help replace the front control arms on a friend's deuce and a half (we didn't have a big enough jack). Yes, we did put blocks under it as jack stands once it was up.
|
# ? Apr 5, 2023 17:04 |
|
*takes a hit from ye olde bong* what if we made a bus but it was like, a double bus. http://www.coachbuilt.com/bui/t/twin_coach/twin_coach.htm
|
# ? Apr 5, 2023 17:33 |
|
“Street car capacity is achieved with riding qualities which bring ejaculations of surprise from every new load of patrons. “ Some interesting quotes in there. Not sure I can imagine a worse drive mechanism than worm drive.
|
# ? Apr 5, 2023 18:21 |
|
boxen posted:Ooooh, red calipers, it's the performance version This particular RV (GMC) is completely different from most RVs. The FWD and swing axles in the rear allowed it to be much lower, and have a flat floor all the way back. It's also an all-fiberglass body. https://en.wikipedia.org/wiki/GMC_motorhome They're pretty cool, and were fairly advanced for the time. Boaz MacPhereson posted:If that 500 ever takes a dump, LS4 is always an option No it isn't. The Toro/Caddy TH425 setup is longitudinal. A normal LS will bolt up with BOP adapters. Q_res posted:Actually, that may not be the small block you want to go with in this setup. There you go. Powershift posted:Maybe a ZZ632 would fit. This is a good time to repost this: https://www.youtube.com/watch?v=nEdIuoCus3Q These are the guys who built it. Whole series of the build on their channel. https://www.youtube.com/watch?v=LC-pfi_NB5Y
|
# ? Apr 5, 2023 18:33 |
|
Turbobago is basically the thumbnail for this thread.
|
# ? Apr 5, 2023 18:38 |
|
bennyfactor posted:Maybe you could put the new corvette engine/trans in ... backward? How much are used Corvette transaxles going for on the used market these days? Probably one of the cheaper 500+hp rated mid engine transaxles out there
|
# ? Apr 5, 2023 18:43 |
|
Hadlock posted:How much are used Corvette transaxles going for on the used market these days? Probably one of the cheaper 500+hp rated mid engine transaxles out there Call up J&D Corvette in socal. They probably have one.
|
# ? Apr 5, 2023 18:45 |
|
Sadi posted:“Street car capacity is achieved with riding qualities which bring ejaculations of surprise from every new load of patrons. “ The Peugeot 404 had worm drive. "Instead of a conventional crown wheel and pinion differential design, the 404 had a worm drive, allegedly to create a lower rear axle profile for extra suspension travel. Its bronze internals required a special castor oil blend."
|
# ? Apr 5, 2023 20:38 |
|
BuckyDoneGun posted:
I think an old air-cooled VW transmission would work as well, no? That'd probably be fine for the amount of power that'd come from a 3-cylinder. I think a Subaru transaxle could be made to work as well, but you'd need a reverse-cut ring and pinion to make it spin the right way (I think that's something that exists), and to disable/cover the driveshaft that'd normally power the rear wheels.
|
# ? Apr 5, 2023 21:49 |
|
boxen posted:I think an old air-cooled VW transmission would work as well, no? That'd probably be fine for the amount of power that'd come from a 3-cylinder. Type1 yes. Most bus transmissions like the 5/6 rib will need R/P replacements. They both are easy to get gears for. The subaru box is a semi popular alternative in the vw sand toy crowd.
|
# ? Apr 5, 2023 22:00 |
|
Motorcycle transmission with a hefty chain?
|
# ? Apr 5, 2023 23:02 |
|
cursedshitbox posted:Call up J&D Corvette in socal. They probably have one. Has there ever been a mid engine inline 8
|
# ? Apr 6, 2023 00:41 |
|
Hadlock posted:Has there ever been a mid engine inline 8 https://www.youtube.com/watch?v=1vYvTbDJuFs
|
# ? Apr 6, 2023 00:51 |
|
|
# ? Apr 6, 2023 01:08 |
|
Hadlock posted:Has there ever been a mid engine inline 8 If Ford had produced its T-drive there probably would have been. We'll just have to settle for a transverse Inline 8 in a Tempo instead... https://www.autoweek.com/news/a1973261/fords-forgotten-t-drive-program/
|
# ? Apr 6, 2023 03:37 |
|
Hadlock posted:Has there ever been a mid engine inline 8 If you use the standard definition of engine in front of the rear axle and behind the front axle, a bunch of them. e: The Auto Union Type A, B, and C cars were all rear-mid engined V-16s. ee: The Cizeta-Moroder V16T had a rear-mid transverse V-16 And 4 popup headlights joat mon fucked around with this message at 04:51 on Apr 6, 2023 |
# ? Apr 6, 2023 03:54 |
|
That is like the best of all I want from old Lambo and Ferrari! God drat!
|
# ? Apr 6, 2023 11:21 |
|
I believe they still have all the tooling, you can order one if you want
|
# ? Apr 6, 2023 12:14 |
|
cursedshitbox posted:Type1 yes. Most bus transmissions like the 5/6 rib will need R/P replacements. Type 1 flipped upside down with hewland internals is one of the go-to setups for vintage racing, all the gear sets you could ever want.
|
# ? Apr 6, 2023 12:39 |
|
Humphreys posted:That is like the best of all I want from old Lambo and Ferrari! God drat! Here's a decent watch if you have the time. https://www.youtube.com/watch?v=y1gH0V4AOCo
|
# ? Apr 6, 2023 15:57 |
|
glyph posted:Here's a decent watch if you have the time. Man that was a struggle to watch.
|
# ? Apr 7, 2023 08:03 |
|
Humphreys posted:Man that was a struggle to watch. Tyrell videos tends to be a tad dispersive but he is the real deal on old classic sports cars.
|
# ? Apr 7, 2023 08:45 |
|
Hadlock posted:Has there ever been a mid engine inline 8 Mid engine, tiny displacement (1.5l), huge supercharger, front wheel drive, dual overhead cam from the 1920s https://silodrome.com/miller-91-race-car/
|
# ? Apr 7, 2023 13:58 |
|
Well sure using that definition all Bugatti made until the 30s was mostly inline 8 mid engine Maybe what the world really needs is a 5.3L inline 8 bolted to a Porsche G50, hanging out the back. We can call it 'badonkadonk'
|
# ? Apr 7, 2023 16:02 |
|
An actual polite, wholesome interaction between motorist and cyclist: (needs sound)
|
# ? Apr 7, 2023 19:46 |
|
AirRaid posted:An actual polite, wholesome interaction between motorist and cyclist: (needs sound) Edit: a different cut of it I managed to find: https://www.reddit.com/r/funny/comments/t0ihdz/yeeeeeeeowwwwwwgggnn/
|
# ? Apr 7, 2023 20:52 |
|
AirRaid posted:An actual polite, wholesome interaction between motorist and cyclist: (needs sound) That's great.
|
# ? Apr 8, 2023 01:35 |
|
AirRaid posted:An actual polite, wholesome interaction between motorist and cyclist: (needs sound) Don't put [img] or [timg] tags on videos. Just the url.
|
# ? Apr 8, 2023 01:48 |
|
|
# ? Apr 8, 2023 03:10 |
|
It's actually a stock Proton Jumbuck with a EVO bodykit
|
# ? Apr 8, 2023 06:29 |
|
CAT INTERCEPTOR posted:It's actually a stock Proton Jumbuck with a EVO bodykit I am aware. But it looks awesome, so correct thread. I'll put it to a vote for fun though.
|
# ? Apr 8, 2023 07:01 |
|
Works for me
|
# ? Apr 8, 2023 07:01 |
|
Humphreys posted:I am aware. But it looks awesome, so correct thread. I'll put it to a vote for fun though. Okay why not? +1 Right thread
|
# ? Apr 8, 2023 07:11 |
|
CAT INTERCEPTOR posted:Proton Jumbuck They're in the lift, and the lorry, and the bond wizard, and all over the Malunga Gilderchuk!!!
|
# ? Apr 8, 2023 07:11 |
|
CAT INTERCEPTOR posted:Okay why not? + Right thread for sure
|
# ? Apr 8, 2023 11:12 |
|
Actual usable truck that doesn't have a bonnet 5 feet in the air and looks cool? Right thread.
|
# ? Apr 8, 2023 11:38 |
|
Right thread.
|
# ? Apr 8, 2023 14:40 |
|
I miss minitrucks
|
# ? Apr 8, 2023 15:00 |
|
|
# ? Jun 4, 2024 17:03 |
|
Beve Stuscemi posted:I miss minitrucks Me too. https://www.youtube.com/watch?v=lad9PuKxOQY
|
# ? Apr 8, 2023 15:15 |