|
Pretty much any UPS store will have a notary. My 18 yr old kid is an Oregon notary due to working at a UPS store.
|
# ? Jul 9, 2023 16:12 |
|
|
# ? Jun 5, 2024 07:44 |
|
Beve Stuscemi posted:Lifehack: Become a notary I looked into that as my wife’s a lawyer & notary in NY: you can’t perform a notarial act if you have an interest in the transaction… TotalLossBrain posted:Pretty much any UPS store will have a notary. My 18 yr old kid is an Oregon notary due to working at a UPS store. Sure, it’s not insurmountable. But coordinating renting a trailer (because lol if you think OH allows you to drive a purchased vehicle back home legally), the notary and a potential lien on a Saturday, while relying on the seller to have their poo poo together, and being a couple of hours ways from home is still a giant pain in the rear end that has to be worth the effort. morothar fucked around with this message at 16:53 on Jul 9, 2023 |
# ? Jul 9, 2023 16:50 |
|
morothar posted:But coordinating renting a trailer (because lol if you think OH allows you to drive a purchased vehicle back home legally), the notary and a potential lien on a Saturday, while relying on the seller to have their poo poo together, and being a couple of hours ways from home is still a giant pain in the rear end that has to be worth the effort. I've ridden 3 bikes home from out of state w/ their original plates; another 2, I threw in a van and drove home. the title notarization and out-of-state title inspection processes are indeed a pain in the dick, and it's even worse if there's no county auditor's office to do the title inspection next to a bmv location near you. extra fun, if you don't have a title in your name, you can't even get a temp tag from the BMV
|
# ? Jul 10, 2023 03:00 |
|
This may be personal preference, make sure someone has their endorsement and/or insurance BEFORE riding the bike. I was over at my friends house rebuilding the suspension on his dirtbike when this guy came to look at his road bike. 1. My friend didn't ask about his riding experience, or if he had his endorsement. 2. He didn't check/ask first to see the cash prior to riding the bike. Honestly most times Ive bought a bike, its surprising how trusting people are as nobody has ever asked me for cash up front or collateral as Ive usually driven my car to their home. The guy gets on the bike (ninja of some sort I wasn't familiar with) and it was 100% clear this guy was not comfortable riding a bike. He struggled shifting and his steering seemed very wobbly. I kept my mouth shut but I thought he was going to end up skidding across the street or end up taking out a mailbox. He then cranked the throttle and whiskeyed up the street a bit. Thankfully it was empty but he didn't hold a straight line. When he went to turn around, you could tell he was nervous as he initiated a turn but backed out several times until he got to an intersection and just used the entire intersection. He also didn't wear a helmet the entire time. When he came back he had some weird excuses for his riding, its been a while, my bike is very different, etc. He ended up buying the bike but not after some asinine attempts to pay far less than asking. He also had to leave, run to the bank to get the cash, and then come back. If the guy was honest and just said "hey, I'm new to riding" maybe it would initiate my friend to go over the controls or help him out but guys are always trying to be macho.
|
# ? Jul 10, 2023 15:34 |
|
Update on the Trident: the shifter detent arm return spring had popped out. The shop claims they haven’t seen that before; the internet is awash with an issue 10 years ago where springs were deemed too weak. Not so much recently. If you know what you’re doing, seems like a few hours or so of labor, plus a new gasket and some washers. They’re waiting for the parts to come in, so I should have the bike back either this or next Saturday. morothar fucked around with this message at 17:48 on Jul 12, 2023 |
# ? Jul 12, 2023 17:16 |
If they fail to do that fix in an hour or less they are either incompetent or criminals
|
|
# ? Jul 12, 2023 18:21 |
|
Slavvy posted:If they fail to do that fix in an hour or less they are either incompetent or criminals It’s under warranty, so it’s their problem. Agree though, there’s a video of somebody doing that job on a Tiger, and it takes him ~an hour. I’ve seen reports of 3-4 hours post-warranty, which would really piss me off.
|
# ? Jul 12, 2023 19:09 |
|
Captain McAllister posted:Bar ends get the mirrors out far enough that I can see behind me. I ran cheapies for years, but got a good deal on used CRG Arrow quick flips, and they're game changing. The mirrors are big enough, the materials are heavy enough, and the mounting system is designed properly so that everything isn't just a blurry mess in them - compared to an Amazon set, where one fell off on the first ride.
|
# ? Jul 13, 2023 02:17 |
|
Had a fuel leak on my Hornet so I've got the carburetors off it and I'm replacing all the seals. Not my first rodeo at all, but I've found that these carbs apparently use a single-d screwhead/driver for the pilot mix screw, which is fine, I'll go source the correct driver for it, but also how on earth do you adjust this screw with the carbs on the bike?
|
# ? Jul 13, 2023 02:32 |
|
RadioPassive posted:Had a fuel leak on my Hornet so I've got the carburetors off it and I'm replacing all the seals. Not my first rodeo at all, but I've found that these carbs apparently use a single-d screwhead/driver for the pilot mix screw, which is fine, I'll go source the correct driver for it, but also how on earth do you adjust this screw with the carbs on the bike? I'm sure I saw in a Honda carb-related video a guy using a D bit on the end of a flexible/spring head. Edit: found it, this video at 8:45 in https://www.youtube.com/watch?v=AKjZ_jCw3cM&t=525s
|
# ? Jul 13, 2023 02:42 |
RadioPassive posted:Had a fuel leak on my Hornet so I've got the carburetors off it and I'm replacing all the seals. Not my first rodeo at all, but I've found that these carbs apparently use a single-d screwhead/driver for the pilot mix screw, which is fine, I'll go source the correct driver for it, but also how on earth do you adjust this screw with the carbs on the bike? Very carefully While you can do what the video above does, I have always just replaced them with regular slot head ones cause I don't want to deal with that bullshit
|
|
# ? Jul 13, 2023 04:41 |
|
Rusty posted:After reading this post I actually ordered this brand (hindsight ls though) and they are pretty awesome. There is no vibration and the picture is better (although smaller) than the stock ones for my XSR. They are also the lane splitting ones so they fold in. Also nice to not have those stock ones in my view when I am riding. I have the arrows on my 701 SM and with the way the bars are on that, I basically have a clean, unobstructed view with them on. The arrows are slightly convex, and you can spin/ flip them on the mounts so the end of the mirror is flush with the end of the bar, or so that they hang over a bit and the slight fisheye effect helps out a bit. Those look clean and cafe-racer ish on your bike, though.
|
# ? Jul 13, 2023 09:22 |
|
CRG build quality is top-notch with one exception, and it's something they may have fixed since the last time I bought any of their stuff: the anodizing will fade really badly with UV exposure
|
# ? Jul 13, 2023 16:54 |
|
Sato says the same thing about their parts, so I assume that is something that just happens with anodizing.
|
# ? Jul 13, 2023 17:02 |
|
I bought an integrated taillight/turn signal unit for my FZ6 since I got cases that hide the rear signals from most angles, and I have a question about the wiring. The taillight itself is pretty self evident, 3 wires to 3 wires, but it’s only got one wire for each signal where the originals have 2. Do I need to do anything with those now superfluous grounds?
|
# ? Jul 13, 2023 21:31 |
You don't, they literally just go straight to earth already
|
|
# ? Jul 13, 2023 21:43 |
|
That’s what I thought but it’s been a long time since I did any electrical theory and wanted to be sure.
|
# ? Jul 13, 2023 21:47 |
|
What is it you're supposed to spray at your carb boots to check for cracks/leaks? Was it ether or starter fluid? Mine look ok at first blush but I feel like it's been getting poppier on decel over the last year or so, figured it'd be an easy thing to check. (Haven't had the plugs out for a while so I can't speak as to the state of them.)
|
# ? Jul 19, 2023 00:47 |
Phy posted:What is it you're supposed to spray at your carb boots to check for cracks/leaks? Was it ether or starter fluid? They're the same thing
|
|
# ? Jul 19, 2023 01:11 |
|
So the S1000 has an 'anti-hopping' (slipper?) clutch...Do they always feel pretty numb at the lever? I've never ridden a bike with one before and I'm finding it to be a bit of a guessing game finding the friction zone by feel, making low speed stuff a litte tricky.
|
# ? Jul 19, 2023 11:29 |
|
that's not a slipper clutch thing, it's a BMW thing
|
# ? Jul 19, 2023 15:40 |
Jazzzzz posted:that's not a slipper clutch thing, it's a BMW thing
|
|
# ? Jul 19, 2023 18:23 |
|
Slavvy posted:They're the same thing Idle didn't budge, so that's good news. Still kinda feel like I should grab a full rack of carb boots for the next time I have to pull them. No guarantee they'll be around in another 2-5 years.
|
# ? Jul 20, 2023 03:11 |
If you're getting decel popping you didn't get before, and there's definitely no vacuum leak, there are a few possibilities arranged roughly most to least likely Pilot circuits dirty/carbs out of sync Fuel quality/contamination Muffler rotting out Air filter disintegrating PAIR system fault Valve clearances tight
|
|
# ? Jul 20, 2023 04:52 |
|
Feels like it's been poppier since at least last year. There's some things on that list that could be the case, a couple that it almost or certainly can't be (air filter's an oiled k&n (and the bike was rejetted appropriately), a PO deleted the PAIR system), and I'm due or even overdue for a valve check But also I started making a conscious effort last year to downshift while braking, rather than clutching in in anticipation, so it's possible I'm experiencing what the bike would have been doing anyway if I didn't suck How do I check the muffler packing?
|
# ? Jul 20, 2023 13:46 |
Is it the original muffler? Congrats it's hosed If it's aftermarket you have to drill out the rivets/remove the screws and take it apart
|
|
# ? Jul 20, 2023 22:04 |
|
Slavvy posted:Is it the original muffler? Congrats it's hosed Nah it's aftermarket. Guessing regular-rear end pop rivets are fine to put it back together?
|
# ? Jul 20, 2023 22:54 |
Yeah just drill them out and put new ones in, there are loads of tutorials on how to do this stuff out there, it's pretty straightforward
|
|
# ? Jul 20, 2023 23:02 |
|
Jazzzzz posted:that's not a slipper clutch thing, it's a BMW thing Ah, fair enough. The clutch lever is a really light pull too which probably doesn't help either. I'm just having to deal with a few jerks when pulling away at slow speeds because I cant tell when its engaging. I'm sure I'll get used to it eventually.
|
# ? Jul 21, 2023 18:44 |
|
at least you aren't stalling it in traffic
|
# ? Jul 21, 2023 22:09 |
|
at least not anymore...the first few days were...fun!
|
# ? Jul 21, 2023 22:25 |
|
If you had to re-wire a bike harness, what weatherproof connectors would you use? My boyfriend has a bike he uses for work and the loom could be charitably described as dogshit: it's mostly a rats nest of these stuffed into the back of the headlamp where they can get nice and wet: https://www.vehiclewiringproducts.co.uk/c-50-connectors/c-117-multi-connectors/p-615-mini-connectors-2-8mm. We've already replaced all the cables along the swingarm because the originals chafed through, and I'm resigned to the fact it's all going to poo poo itself one day so I have a project in mind to build a replacement loom ahead of time. I'm not scared of wiring, but this is my first foray into vehicle connectors and I'm overwhelmed by the range of choice. Any pointers would be much appreciated!
|
# ? Jul 23, 2023 15:53 |
|
Whatever connector you choose, please buy the right crimp tool for it, preferably from the same vendor. Anecdotal stuff: back when I was riding/working on standup jetskis a lot, I was very fond of water proof Japanese bullet connectors. I think these were even available with pre-filled solder cups so you would just use a heat gun to solder and heat shrink it in one step. Yamaha uses them as OEM parts.
|
# ? Jul 23, 2023 16:17 |
|
TotalLossBrain posted:Whatever connector you choose, please buy the right crimp tool for it, preferably from the same vendor. No worries there, I can't stand using poo poo tools and I only want to do this once so I'm buying a good crimper if I actually go through with this. Those waterproof bullets look interesting; is there any concern about vibration shaking them apart or does the heatshrink take care of that?
|
# ? Jul 23, 2023 16:59 |
|
The metal pieces interlock and the insulation covers also overlap, making for a pretty secure connection. I probably wouldn't use these to redo a motorcycle wiring harness as they are not very space efficient and it might suck to have to plug/unplug individual wires when you could be using a multi pole connector.
|
# ? Jul 23, 2023 17:24 |
Cheap but good option: weather pack connectors. Often found on lower end race bikes and Italian bikes, they're waterproof and light. Expensive but very good option: deutsch connectors, often found on Harleys, they're waterproof and last forever.
|
|
# ? Jul 23, 2023 21:08 |
|
I went to AMP superseal for car stuff, there are slightly smaller options for motorcycle stuff tho I guess.
|
# ? Jul 23, 2023 21:14 |
|
Whatever connectors and then just blob a poo poo ton of dielectric grease in them
|
# ? Jul 23, 2023 21:43 |
Beve Stuscemi posted:Whatever connectors and then just blob a poo poo ton of dielectric grease in them Also an option, this is the factory method on a lot of scooters
|
|
# ? Jul 23, 2023 21:45 |
|
|
# ? Jun 5, 2024 07:44 |
|
Does this sound like brake pad contamination? The previous owner of my FJR had a fork seal leak and a leaking banjo fitting. He had them fixed, all is dry now, but i can clearly see dried residue from both on the calipers. The front brake is really weak. Almost dangerously so. The lever is nice and firm, so I don't suspect air (I'll be bleeding the system regardless), but there's just nowhere near the stopping power there should be. Assuming that's the case, is trying to clean them a fool's errand?
|
# ? Jul 25, 2023 14:55 |