|
You can also dry it out gently in the oven before use.
|
# ? Jun 22, 2013 14:27 |
|
|
# ? Jun 9, 2024 05:00 |
|
Sagebrush posted:Are there any places that sell small amounts of PLA filament, like half a pound or so? Maybe in variety packs of different colors? I need some blue filament to print a couple of TARDISes for my sister, but I've got so much filament sitting around in a variety of other colors that I'm already worried about using it all up before it absorbs too much moisture. It's not available yet, but I imagine the 3Doodler guys will be selling strands of filament once their product launches. With the nature of that product, I doubt most people will want to buy rolls of filament and instead will want small strands of a variety of colors.
|
# ? Jun 22, 2013 19:24 |
|
Faberdashery sells a "rainbow pack". It's a good blend and they have some of the best PLA on the market.
|
# ? Jun 23, 2013 01:19 |
|
Hmm curious, every now and again I check Makerbot's 2X page because I'm window-shopping for whenever it is I upgrade to a new printer. It now says "We are currently unable to take orders for the 2X". Changing the design, perhaps? Or too busy lifting their wallets?
|
# ? Jun 26, 2013 17:23 |
|
Interesting. Windows 8.1 is now going to include 3d printer drivers pre-installed: http://blogs.technet.com/b/microsoft_blog/archive/2013/06/26/3d-printing-with-windows.aspx
|
# ? Jun 26, 2013 19:46 |
|
Mister Sinewave posted:Hmm curious, every now and again I check Makerbot's 2X page because I'm window-shopping for whenever it is I upgrade to a new printer. It now says "We are currently unable to take orders for the 2X". Considering how much email I've sent back and forth alone on my issues with the 2x I'm guessing they're at least trying to fix some of it's problems, they also might just be really behind. It took 8 weeks to get mine and here nearly a month later I still don't have my hood for it. I've been so fed up certain problems on mine like the ever-warping build plate (that I've replaced once and got back a new one that was no bettter), I've gone and ordered aluminum arms, a heated glass build plate, printed new extruders, and installed the sailfish firmware just to skip past the stock machine's problems and work towards maximizing its potential.
|
# ? Jun 26, 2013 19:58 |
|
Wow, that's not at all what I was expecting. I kind of figured that with the enclosure and focusing on ABS most of the issues I have with ABS printing would be addressed. Sounds like it really just has different problems.
|
# ? Jun 26, 2013 21:14 |
|
Got my filastruder kit today! Now to come to terms with the fact I have no idea what I am doing when it comes to assembling this.
|
# ? Jun 27, 2013 22:54 |
|
Faltion posted:Got my filastruder kit today! Now to come to terms with the fact I have no idea what I am doing when it comes to assembling this. Take a long time cleaning out the chaff around the cuts in the iron pipe. You'll do yourself a lot of favors. I'll post some pictures of my assembled kit, although it's not running as well as I'd like yet.
|
# ? Jun 27, 2013 22:59 |
|
So I have a Solidoodle 3, and had been using PLA with it lately. Today however I tried to go back to ABS and went to turn the heater bed on and the printer died. The light started to flicker on and off slowly and the extruder head and fan were also flickering on and off. It's not a connection issue with the computer or the on board CPU. I also checked the power cable for issues as well as the plug for shorting and nothing was there either. Help.
|
# ? Jul 1, 2013 19:46 |
|
Nanoscale 3D printing. https://www.youtube.com/watch?v=wThtfAtB5U8
|
# ? Jul 3, 2013 02:35 |
|
SynthOrange posted:
I want to see the video of them putting the glasses on that fly just for the inevitable .gif animation.
|
# ? Jul 3, 2013 02:45 |
|
SynthOrange posted:
That glasses picture has been around for a LONG time, I'm 90% sure it was laser-cut (It's also way bigger than nanoscale). It brings me great joy that the video was someone building a nano-Hellcat. I just came into a Mk2 Fab@Home, and I'm trying to figure out what to do with it. The motor and controller don't seem to accept most available plans because it uses servos instead of steppers. Also, I've only seen one person that reliably fit an ABS extruder onto it. Does anyone know a resource for upgrading/converting one of these? Otherwise, I think I might strip down the controller and servos for a future project, and replacing them with more standard bits. Edit: The only way I can see to do solid parts is either silicon, cement, or a UV-resin after fitting a UV LED to the undercarriage of the syringe. All of those options seem like a lot more work, or more expensive in the long run than a conversion.
|
# ? Jul 6, 2013 03:05 |
|
Hello everyone. I recently entered a contest hosted locally. Make a cool model, win a Makerbot Replicator 2x. I'm fairly new at 3D stuff in general and this was the first time I'd ever made something for printing, but I got to have my entry printed out for free. It wraps up on Thursday, and I hope I win! Right now I'm trying to clean up and paint the model. (If you are interested in following my art and stuff, the full blog with more pictures and stuff is here.) This is the Zbrush model it was printed from: I was pointed towards doing this because my friends want me to model all their D&D minis for them for free, haha! But honestly I think this stuff is all really cool. I don't know a whole lot about it yet, but if I win this printer I plan to use it. I learned a lot by making this little dino dude.
|
# ? Jul 6, 2013 20:18 |
|
Has anyone got any experience with 3DSystems' CubeX printers? They sound nice and have a nice big build volume. I am interested in ABS only printing and want a big build volume, and am particularly interested in printers that have in some way taken steps to address warping, etc issues with ABS (by far my biggest bugbear with it.) I had always shortlisted the Replicator 2X for the ABS focus, big build volume, and enclosed build platform for temperature control. But honestly the more I hear about them the less enthusiastic I am about the idea. The optimizations don't seem to pull their weight and some of the other hot end and feed design stuff just seems behind the curve. I wish I could try one out and see for myself. Ran across the CubeX stuff, couldn't tell much more than what the ad copy says. Anyone used them?
|
# ? Jul 11, 2013 00:47 |
|
Mister Sinewave posted:Has anyone got any experience with 3DSystems' CubeX printers? A coworker of mine purchased one looking for exactly the same sort of printer. He's had nothing but trouble. They've shipped him 2 different printers, and both have had some major issue or another. They've got one guy working support for the entire company. His only saving grace is that they accidentally forgot to bill him. His first printer's extruder clogged hopelessly, and after repairing it, the electronics failed. The second printer, a Z-endstop failed, the extruders slammed into the build platform, and sheared off the extruder barrel. A third is on the way. After looking at their support, their design, and their crappy "buy our filament only" model, I wouldn't recommend them. They're 80% of the way to a useful at-home 3D printer, but it isn't yet working out.
|
# ? Jul 11, 2013 01:52 |
|
Mister Sinewave posted:Has anyone got any experience with 3DSystems' CubeX printers? Funny you ask, I just came on here to see if anyone else was having issues with them. We just got 4 CubeX Duos and they have been a major pain in the rear end. We have had them now for about 2 weeks and have only gotten 1 decent model out of them. They take a lot of calibrating, their build plates need adjusting out of the box, and we have had a few parts fall off of them. Their cleaning mechanism, which is suppose to wipe off the little half melted plastic whisps they drop every where, is not very effective and those whisps can end up screwing up the whole model by preventing the printhead from laying down a layer. After these issues with the CubeX Duos I do not think we will be ordering any more.
|
# ? Jul 11, 2013 05:11 |
|
Here in the UK, Maplin has started taking pre-orders of the Velleman K8200, a £700 PLA only printer with a 200mm cube build area, 0.15mmm accuracy
|
# ? Jul 11, 2013 18:43 |
|
Wow, those are some not-encouraging experiences with the cube stuff. Thanks for sharing.
|
# ? Jul 11, 2013 18:49 |
|
Cakefool posted:Here in the UK, Maplin has started taking pre-orders of the Velleman K8200, a £700 PLA only printer with a 200mm cube build area, 0.15mmm accuracy That...isnt' that exciting really. You could DIY a Prusa or Mendel90 with better numbers on every front for roughly the same cost (if not a bit cheaper).
|
# ? Jul 11, 2013 19:21 |
|
Yes, but this is the first brick and mortar store in the UK selling a 3d printer. It's likely to be the first time most people have seen one. I'd not buy one for the reason you suggest but it's an interesting development.
|
# ? Jul 11, 2013 20:15 |
|
Ah, that's the part I missed. Is that like Staples over in MURICA selling the Cube then?
|
# ? Jul 11, 2013 20:18 |
|
Pretty much. Maplin sell electronic components, some pc poo poo, gadgets, tools, soldering supplies, basic prototyping, that sort of crap
|
# ? Jul 11, 2013 20:47 |
|
Zuph posted:The second printer, a Z-endstop failed, the extruders slammed into the build platform, and sheared off the extruder barrel. We just had one of our CubeXs do this today. I do not recommend these at all if you need a reliable and consistent printer. We are pretty disappointed these have worked so poorly, we hoped these would be competitive speed/build material cost wise with our UPrints or our ZCorp powder printer but we can't even get one of these CubeXs to work.
|
# ? Jul 11, 2013 23:09 |
|
That IS disappointing, especially considering they are on the spendy side of the home 3D printer price spectrum.
|
# ? Jul 11, 2013 23:37 |
|
What is the function of the z end stop? Do you not touch off on a shim to set your z offset?
oxbrain fucked around with this message at 03:03 on Jul 12, 2013 |
# ? Jul 12, 2013 01:15 |
|
oxbrain posted:What is the function of the z end stop? Do you not touch off on a shim to set your a offset? Most printers that I am aware of rely on the end stop to determine the bed zero/offset
|
# ? Jul 12, 2013 02:28 |
|
That seems like an accident waiting to happen.
|
# ? Jul 12, 2013 03:04 |
|
oxbrain posted:That seems like an accident waiting to happen. What other option is there? This isn't a software controlled end stop but rather a mechanical switch. I thought it was a pretty standard end stop mechanism for CNC machines?
|
# ? Jul 12, 2013 16:25 |
|
It's not used to set work offsets because most cnc machines aren't dealing with a fixed work piece. They set machine coordinates that way, but the switch will always be in the direction away from the work area and there will almost always(HASS ) be a physical switch behind it that directly cuts power to the servo before it crashes. For a printer with a fixed bed height you enter in the offset from there and you're zeroed at the bed without ever coming near it.
|
# ? Jul 12, 2013 20:01 |
|
oxbrain posted:It's not used to set work offsets because most cnc machines aren't dealing with a fixed work piece. They set machine coordinates that way, but the switch will always be in the direction away from the work area and there will almost always(HASS ) be a physical switch behind it that directly cuts power to the servo before it crashes. Most of these machines are using steppers, not servos. They have to zero to something on startup as there's no direct measurement readout. I have my z-stop set to .2mm below my print bed, which is spring-mounted. It can hit and mangle a print, but a crash into the bed doesn't break anything. These are mechanical stops that cut power to the pololu board. I've got a microswitch about .15mm up (0.5mm below surface) that's wired to the software side for zeroing.
|
# ? Jul 13, 2013 00:34 |
|
Don't leave your PLA printed parts in the car
|
# ? Jul 18, 2013 03:35 |
|
Tell me it still works but now prints everything in italics.
|
# ? Jul 18, 2013 03:43 |
|
For some reason though, it only does that in the car. Normal PLA will take like 160F temps just fine and only soften a bit but you put it in the car when its 92F outside and you come back to a puddle of printer.
|
# ? Jul 18, 2013 04:22 |
|
insta posted:For some reason though, it only does that in the car. Normal PLA will take like 160F temps just fine and only soften a bit but you put it in the car when its 92F outside and you come back to a puddle of printer. Depending on where you live and what color your interior is, it can certainly get up to 160F and stay there for a bit. I came back to a puddle of BB gun once. Have also exploded alkaline batteries, sodas, and eggs in the back seat.
|
# ? Jul 18, 2013 06:57 |
|
It's why you dont leave animals, children, elderly or pressurized containers in cars. They're basically solar ovens in the open.
|
# ? Jul 18, 2013 07:20 |
|
About once every summer I get a canned soda at lunch and end up saving it for later and leaving it in the cupholder of my car, then when it's time to go home I find this: Yes, those spots in the headliner are Dr Pepper syrup. It gets hot in cars.
|
# ? Jul 19, 2013 20:21 |
|
One of the Makibot creators did a little writeup about the windows native printing stack that I found kind of informative to read (as a not-yet-owner of a 3d printer): http://makibox.com/blogpost/items/native-3D Interesting that the file format MS is proposing allows for curves and such rather than the current STL method of using dots with straight lines between them.
|
# ? Jul 19, 2013 20:53 |
|
I'd be happy if they would just add a preview viewer that could render thumbnails (maybe even rotating ones?) for STL files. Is there anything like that for Windows 7?
|
# ? Jul 20, 2013 23:13 |
|
|
# ? Jun 9, 2024 05:00 |
|
Yesterday I entered the world of desktop manufacturing with the arrival of my Replicator 2. I spent the day printing various things from Thingverse and came across the this issue with one of the items: As you can see in the pic there are filaments hanging off the orbs that make up the joints (and to a lesser extent some random other spots). What causes this and what can I do to avoid it in the future? Out of the many items I printed yesterday (stretchlet, chain, tesseract, comb, filament spool clips, and a clip-on tool holder) that was the only one that came out...strange. EDIT: After touching it up a bit I'm guessing it was the lack of supports while it was being printed. Sagebrush posted:I'd be happy if they would just add a preview viewer that could render thumbnails (maybe even rotating ones?) for STL files. Is there anything like that for Windows 7? That would be amazingly useful. I've just been putting screenshots in the folder with my .STLs. Get's cumbersome. TheKeeper fucked around with this message at 03:24 on Jul 21, 2013 |
# ? Jul 21, 2013 03:03 |