|
nwin posted:Is there anything difficult about choosing a type of carpet or installer? When I’ve rented, my landlord just went with the cheapest carpet at Home Depot or lowes, but my new house needs new carpet in three bedrooms and I’d like to not cheap out on it because I’d like it to last 10+ years. $2-3/sqft for decent commercial grade carpet installed is the going rate here. Maybe they use really high end stuff but I bet you could find a better deal without much extra work
|
# ? May 31, 2022 21:23 |
|
|
# ? May 30, 2024 02:39 |
|
Sous Videodrome posted:I just learned about smart water shutoff valves. I like the idea of something that will shut off water to the house in case of a leak. But I don't want it connected to the internet. I don't want an app, and I don't want to have to pay for a subscription. Is there such a thing? Are they called something besides "smart water shutoff"? "Smart" implies an internet connection or a sensor. What kind of function are you expecting?
|
# ? May 31, 2022 23:02 |
|
Just shutting off the water if it detects a leak condition.
|
# ? May 31, 2022 23:06 |
|
Harriet Carker posted:How? I can screw the screw into the drywall no problem, but I can't make a hole big enough for the anchor. A hole in drywall is just that. If you have a nail or larger screw slightly larger than the mounting screw you can use that and seat the anchor. El Mero Mero fucked around with this message at 23:17 on May 31, 2022 |
# ? May 31, 2022 23:10 |
|
devmd01 posted:I’ll sod this in in the spring. Put sod in two weeks ago, it’s already bedded in nicely thanks to the topsoil and lots of rain. Like it was never there! (In about another year).
|
# ? May 31, 2022 23:59 |
|
First of all, I'm fully in agreement about not wanting to use poisons. I think I had dead mice in my walls at my old apartment and the smell was awful and persisted for quite some time. Next question is what about this product. The active ingredient is corn gluten meal and table salt-- but my understanding is still that this effectively poisons them by somehow causing them to stop drinking water which seems pretty gruesome and slow. I only ask about this product because it was what someone pointed to at Lowe's when I was looking for the conventional snap traps. https://www.tractorsupply.com/tsc/product/ratx-throw-packs-12-oz-box-620108 SubponticatePoster posted:I can't weigh in on the cost, but I can give you some advice in general speaking as a former animal control officer (we didn't respond to these kinds of complaints but we would give people advice on how to handle them). BonerGhost posted:I can't speak to their rates, but I personally would never pay someone to encourage animals to die and rot in my walls in any climate, let alone humid Austin, especially if they're not going to prevent the drat things getting in. Trapping has its controversies but it's not going to remotely be effective if you don't close the holes. Might be time to get on the ol' YouTube and start looking up pest control accounts to get some tips on finding and sealing entrances. Even if you truly have rats and not mice, the holes will be smaller than you expect (mice are like ghosts, so you have to look for their poop). Even my fat rear end 650gm pet rats could get under a door gap of about an inch. If it were me, to minimize the carcasses in my house, I would first trap and then seal the holes, because if you seal up the place with them inside, they're probably still going to die in there. Wild rodents are rude as hell and spread disease so you have to do what you have to do, but that's a smell you just don't forget and it's not fun to have in your house. "Only a few days" is a bald-faced lie, and EPA mandates that bromadiolone be used in tamper proof/resistant bait stations in just about every application except putting it next to a rat burrow, so idk why they're suggesting they might not need them. Good points about cleaning/removing the insulation before doing exclusion. Presumably this service that I was going to hire to vacuum out the insulation and air seal the house is familiar with safe practices on removing old insulation. I assume they would wet it down for their own benefit, but I suppose it is a question I can ask. I'm getting another pest control person to come by my house tomorrow to give me a quote or take a look at the issues. From his website he states he does not use poisons, which is my preference.
|
# ? Jun 1, 2022 00:20 |
|
Toebone posted:My kitchen has some crummy old fluorescent light panels in the drop ceiling (2’ x 2’) that I’d like to replace with LED panels. Any brands / retailers I should look into?
|
# ? Jun 1, 2022 01:41 |
|
SubponticatePoster posted:Very important vertebrate pest control stuff There was a whole thing where I was asked to start a thread on pest control, vertebrates are not my thing I'm an ag/herbicide person any interest in just paying attention to this in case you can contribute please and thank you? https://forums.somethingawful.com/showthread.php?threadid=3944991
|
# ? Jun 1, 2022 04:43 |
|
I finally stepped foot into my local tool library today. Holy poo poo what a cool place. $50 suggested donation to become a member. They host classes on all kinds of topics, have a wood shop you can book for private use, lots of tools and other stuff. Yard, auto, general diy, etc. Super awesome place.
|
# ? Jun 1, 2022 08:17 |
|
That is a super cool idea. I didn't know that kind of thing existed.
|
# ? Jun 1, 2022 15:23 |
|
Verman posted:I finally stepped foot into my local tool library today. Holy poo poo what a cool place. $50 suggested donation to become a member. They host classes on all kinds of topics, have a wood shop you can book for private use, lots of tools and other stuff. Yard, auto, general diy, etc. Super awesome place. What country?
|
# ? Jun 1, 2022 17:07 |
|
VelociBacon posted:Highly recommend this Dewalt 20v Max drill set. BonoMan posted:Yeah this is the drill I have. I love it. Thirding this. I also have this drill and it is a wonderful tool. Small, light, and balanced enough that it's not a strain on my wrists to use yet powerful enough to drive 3" screws through pressure-treated lumber with ease.
|
# ? Jun 1, 2022 17:37 |
|
I've deleted a much more long-winded draft of this post and distilled it down to what I hope is a pretty straightforward question: I want to attach something to an exterior windowsill, and the easiest way to do that would be to drill into the sill -- but that won't work because it's not wood, but vinyl or some sort of composite. Without getting too in the weeds of trying to describe my windows, is there a well-known solution to this dilemma that I might be overlooking? I've considered window box planter brackets, but unfortunately these windows also have a bit of a lip, so I don't know if those will work. I kind of want to do something like just Velcro taping a piece of wood to the sill and drilling into that. But a not awful version of that.
|
# ? Jun 1, 2022 18:27 |
|
VelociBacon posted:What country? US, Seattle. I moved to my neighborhood about a year ago when we bought our first house. I drove by this place often on my way through the neighborhood but they keep odd hours and I didn't have a specific reason to go in. I've already got a good deal of tools, but being a new home owner comes all sorts of new projects I'm not equipped for. There's a certain amount of tools I want to own because they get used often, but I don't want to invest in things I might only use once or twice, like a pex crimper or a tile saw. The only thing is all their powered tools are all battery or corded electric, no gas. I needed a tiller for redoing my yard and all they had was a small plug in which would have been a huge pain. I ended up finding a good deal on a husqvarna for what it would have cost me to rent for a weekend. Overall I think its going to be great when we start to redo the house in the next few years and I'm honestly surprised this isn't more of a thing.
|
# ? Jun 1, 2022 18:52 |
|
Sir Lemming posted:I've deleted a much more long-winded draft of this post and distilled it down to what I hope is a pretty straightforward question: How much does this something weigh? Your fastening options depend greatly on the answer to this question. If it's light enough, there's an exterior version of the 3M Command Strips that I'd look at before attempting the wood+velcro solution. If it's too heavy for Command Strips then you probably need to attach it to structure somehow.
|
# ? Jun 1, 2022 19:07 |
|
PremiumSupport posted:How much does this something weigh? It's a pretty small hummingbird feeder. Not sure how much it weighs when filled with liquid, but it actually comes with suction cups meant to attach to window glass, so it can't be that heavy. However, since it's a second floor double-sash window with a sliding half-screen which I still want to be able to open sometimes, I'm trying to figure out something different. The suction cups are not pre-attached, it also comes with screws that you're free to drill into either the suction cups or something else.
|
# ? Jun 1, 2022 19:29 |
|
Sir Lemming posted:I've deleted a much more long-winded draft of this post and distilled it down to what I hope is a pretty straightforward question:
|
# ? Jun 1, 2022 21:22 |
|
slidebite posted:Do you have a photo you can post of your window/sill/frame? 2 of these are actually the 2nd-story window, the other one is ground level since it was easier to get an exterior shot there obviously. They are all pretty much identical as far as I know, any size or form factor differences would be negligible. (This might also shed light on why I'm trying not to do the suction cup thing -- it's overly long to explain it in words, but I think you can vizualize how it would either be a pain to maintain it, or just very awkwardly positioned.)
|
# ? Jun 1, 2022 22:29 |
|
VelociBacon posted:What country? Guessing this is tool 'library', meaning this is a private organization not anything government run. Like a 'maker space' which had their heyday a few years back. Also guessing it is good old USA.
|
# ? Jun 1, 2022 23:09 |
|
Inner Light posted:Guessing this is tool 'library', meaning this is a private organization not anything government run. Like a 'maker space' which had their heyday a few years back. Also guessing it is good old USA. I guess I'm surprised to see a socialist solution in the states. I moved about a month ago into a condo that has a communal workshop in the basement parking area and it's been fantastic.
|
# ? Jun 1, 2022 23:23 |
|
VelociBacon posted:I guess I'm surprised to see a socialist solution in the states. I moved about a month ago into a condo that has a communal workshop in the basement parking area and it's been fantastic. They don't usually last long in my experience. Misuse and abuse of tools destroys the ones that aren't immediately stolen when new. Without decent tools available nobody wants to keep it going. That was my experience in 2015 or so though, maybe things got better.
|
# ? Jun 1, 2022 23:30 |
|
If you're ready to drill into window sills, how about mounting a bracket higher up next to or above the window so you can hang the feeder in a visible place? My uncle has his hanging from the gutter. Stick-on hooks are always great, 3M has some for outdoor use like xmas lights. There are also old school hooks that you heat the adhesive with a lighter that can attach to textured surfaces. https://www.target.com/c/wall-hooks-hook-racks-hardware-home-improvement/adhesive-hooks/-/N-5xtt4Z35wwv
|
# ? Jun 1, 2022 23:44 |
|
Anybody have an oil-fired furnace? When I bought the house in December the inspector suggested I get a service contract with a local oil supplier during the summer to lock in a low price. At first glance this seems like an obviously good idea because prices probably aren't getting cheaper anytime soon, but I have no experience in this area so I don't know if that's actually a pratfall for some reason. Anyone here have any wisdom?
|
# ? Jun 2, 2022 00:39 |
|
I got absolutely hosed on oil prices in april during a cold snap in new england. Do it.
|
# ? Jun 2, 2022 02:10 |
|
Verman posted:I finally stepped foot into my local tool library today. Holy poo poo what a cool place. $50 suggested donation to become a member. They host classes on all kinds of topics, have a wood shop you can book for private use, lots of tools and other stuff. Yard, auto, general diy, etc. Super awesome place. My local library runs a Kitchen appliance and tool lending library that is just incredible. it's loving fantastic and has saved me thousands of dollars. Basically every time I have a project where I need a "one-off" tool I just check it out from there instead of buying something. They also lend ladders in basically every size, which means I only need 1 ladder of my own. If I check out a tool more than like a dozen times I just go ahead and buy it at that point.
|
# ? Jun 2, 2022 02:53 |
|
Eason the Fifth posted:Anybody have an oil-fired furnace? When I bought the house in December the inspector suggested I get a service contract with a local oil supplier during the summer to lock in a low price. At first glance this seems like an obviously good idea because prices probably aren't getting cheaper anytime soon, but I have no experience in this area so I don't know if that's actually a pratfall for some reason. Anyone here have any wisdom? e: strongly recommend knowing a guy. if one is your cousin or your husband, even better Anne Whateley fucked around with this message at 03:11 on Jun 2, 2022 |
# ? Jun 2, 2022 02:59 |
|
Eason the Fifth posted:Anybody have an oil-fired furnace? When I bought the house in December the inspector suggested I get a service contract with a local oil supplier during the summer to lock in a low price. At first glance this seems like an obviously good idea because prices probably aren't getting cheaper anytime soon, but I have no experience in this area so I don't know if that's actually a pratfall for some reason. Anyone here have any wisdom? You will be lucky to find anybody locking in a rate that isn't basically thievery right now. It's tough. I'm counting the days till I can shitcan my oil company and at least try for a new one. They unilaterally informed me today that they were enrolling me in a "budget protection plan" so they could charge me all summer for oil they'd deliver this winter (but don't forget, if the price of oil goes up, we'll take more money this summer too!). Eat my entire rear end, shitheads.
|
# ? Jun 2, 2022 03:02 |
|
Verman posted:I finally stepped foot into my local tool library today. Holy poo poo what a cool place. $50 suggested donation to become a member. They host classes on all kinds of topics, have a wood shop you can book for private use, lots of tools and other stuff. Yard, auto, general diy, etc. Super awesome place. This is awesome, is that a one time donation? Do you check stuff out or use it there only? I want to take pictures of my local small hardware stores. There’s one within a couple blocks and the other a bike ride away and they’re both classic. The one down the street looks like my tool shed just slightly more organized and much bigger yet no more spacious. The roll up doors are always open and there’s always at least three guys up front that are super nice and obviously seem like they huff glue on the weekend. love that place.
|
# ? Jun 2, 2022 04:27 |
|
Thank you all to who recommended drills! I got the Dewalt set and some drill bits and drilled the first holes of my life today. It went very well and my customer is pleased.
|
# ? Jun 2, 2022 05:06 |
|
Anne Whateley posted:That is what New Englanders do fwiw Yep, I live in the region. Moved here in 2017 but just bought the house end of last year. tracecomplete posted:You will be lucky to find anybody locking in a rate that isn't basically thievery right now. It's tough. Thanks for the heads up on this one
|
# ? Jun 2, 2022 06:08 |
|
Phil Moscowitz posted:This is awesome, is that a one time donation? Do you check stuff out or use it there only? It's a one time suggested donation. You can always donate more or less if you want. They're also accepting of tool donations and volunteering. When you check tools out, you get them for a full week. You can extend tools if someone hasn't requested/wait listed it. They have late fees but it sort of sounds like they're very lenient about forcing any payment. Also tools are free to use. No real limit on what you can borrow at once. They've been open for 10+ years from what I recall. The place is busy every time they're open. Lots of community engagement, lots of volunteers who all seem incredibly patient, outgoing and willing to help with whatever you need. They operate as a non profit so making money isn't their thing.
|
# ? Jun 2, 2022 07:39 |
|
peanut posted:If you're ready to drill into window sills, how about mounting a bracket higher up next to or above the window so you can hang the feeder in a visible place? My uncle has his hanging from the gutter. Y'know, maybe I'm going about this all wrong -- I'm wondering if I can actually get the suction cups to stick to the windowsill somehow. I'm guessing it won't work very well on the vinyl itself. But maybe something like packing tape to create a more suction cup-friendly surface? Or maybe use 3m adhesive strips to mount a plastic rectangle (or I guess metal or glass if I could find it) and then stick to that. I think I may try something like that. (Hanging it isn't an option, it's not that kind of feeder. It's meant to be mounted as a platform which provides a clear view of the hummingbirds.)
|
# ? Jun 2, 2022 12:58 |
|
Suction cups suck, literally and figuratively in a bad way. They are likely to warp in the sun. Use 3M products.
|
# ? Jun 2, 2022 15:05 |
|
Branch fell and took out a chunk of fence two weeks ago. It was on a telecom line and I didn't want to gently caress with potentially damaging expensive equipment so I've been waiting for Comcast to come out and move the branch. Probably stupid to wait, but they came yesterday to move the branch. Now I can chop up the giant tree branch and fix my fence and that's p cool .
|
# ? Jun 2, 2022 15:31 |
|
VelociBacon posted:Highly recommend this Dewalt 20v Max drill set. love it
|
# ? Jun 2, 2022 19:59 |
|
I’m looking for some input on a shelving issue. I have this: https://www.lowes.com/pd/Project-Source-Heavy-Duty-5-Tier-Storage-Shelving-Boltless-48Wx24Dx72H-Powder-Coated-Grey/1002864606 Basically, it’s a shelving unit with five 24” x 48” shelves with 1/4” particle board decking. Problem: I live in the Houston area and this is in my garage. The decking is sagging as it dies a slow, painful death to the humidity. What’s the most cost-effective solution for replacing these with heavy gauge steel wire/mesh decking? Each shelf will need to hold a few hundred pounds of stuff evenly distributed over the shelf. All of the pre-made wire decking inserts are expensive and on backorder.
|
# ? Jun 2, 2022 20:20 |
|
Find a local metal distributor or machine shop that will cut it for you. You might have to call or walk in and talk to someone. I use onlinemetals.com but I can do local pickup, shipping is expensive. 1/2 inch plywood will be an adequate replacement as well, tho
|
# ? Jun 2, 2022 22:19 |
|
Half-inch or 3/4” plywood MDF and OSB are abominations that should be fired into the sun.
|
# ? Jun 2, 2022 23:57 |
|
Motronic posted:There was a whole thing where I was asked to start a thread on pest control, vertebrates are not my thing I'm an ag/herbicide person any interest in just paying attention to this in case you can contribute please and thank you? That tool library is awesome, wish there was something like that around me. There also used to be DIY garages with lifts and stuff you could rent but they've all gone out of business which sucks.
|
# ? Jun 3, 2022 21:08 |
|
|
# ? May 30, 2024 02:39 |
|
I'm trying to loosen my bathroom faucet handle cartridges and the nut is stuck. I saw you can use vinegar to dissolve the built up mineral deposits, but I can't immerse/soak it, so I've just been pouring some on and letting it sit. So far, it's still just as tight as when I started. Are there any other techniques I should try? Edit: I got it! Used a hair drier to heat it up and it came right off. Now, I don’t know the brand and I need a replacement cartridge. Can I just pop in the thing that looks the closest at Home Depot? Edit 2: I found a product code etched into the cartridge and found a matching pair! Finished installing and I’m drip free. Harriet Carker fucked around with this message at 21:19 on Jun 4, 2022 |
# ? Jun 4, 2022 15:22 |