|
On the Stratasys/Dimension uPrint Plus at work, it has a second nozzle for a proprietary support material called SR-30. It sort of melts away under a certain pH level of lye solution and agitation/heat, but it is still best to remove as much by hand ahead of time as possible. (It's kind of gross, to be honest.)
|
# ? Oct 23, 2013 03:06 |
|
|
# ? May 9, 2024 03:42 |
|
Sagebrush: HIPS doesn't seem to adhere to PLA, but PVA does. Nothing sticks to Nylon AFAIK (it's hard to get flat prints actually, it likes to curl ... at least my cheap Nylons do)
|
# ? Oct 23, 2013 04:06 |
|
insta posted:Sagebrush: HIPS doesn't seem to adhere to PLA, but PVA does. Nothing sticks to Nylon AFAIK (it's hard to get flat prints actually, it likes to curl ... at least my cheap Nylons do) A friend of mine did a really interesting mixed layer print of nylon and laywoo-d3 - worked great!
|
# ? Oct 23, 2013 07:03 |
|
For the nylon printers trying to get it to stick to the bed. Has anyone tried using a nylon stocking slipped over the glass/aluminum tray and then glued with PVA as a base? It seems that the nylon would stick to other nylon quite well?
|
# ? Oct 24, 2013 05:03 |
|
insta posted:The new hotness for hobby printers is adding a soluble support material as a second extruder. A few years ago it was PVA (polyvinyl alcohol -- Elmers glue!) with PLA plastic. PLA has its disadvantages, so HIPS (high impact polystyrene) is a support for ABS. PVA won't adhere to ABS, so you have to use compatible plastics. HIPS dissolves with Limonene (retail DeSolvIt) with doesn't harm ABS but rather leaves it with an orangey fresh scent Is there a way to get ReplicatorG to use a second nozzle to do this? I haven't done much research, but it seems like only Makerware does this out of the box and it doesn't like my Replicator (can't flash the new firmware) and it likes to bluescreen my machine. For that matter, is there a new alternative to ReplicatorG? It looks like development stopped November of last year.
|
# ? Oct 26, 2013 14:57 |
|
Does anyone know a good place to order the K8200 in europe, online? It's out of stock on every Swedish site, and the other sites I can find charge more than 20% extra.
|
# ? Oct 27, 2013 02:25 |
|
Hu Fa Ted posted:Is there a way to get ReplicatorG to use a second nozzle to do this? I haven't done much research, but it seems like only Makerware does this out of the box and it doesn't like my Replicator (can't flash the new firmware) and it likes to bluescreen my machine. There is a script for an older version of RepG that does this automatically if you have two extruders on a Replicator 1. I used it for a bit, but support material got better and I stopped caring. I'm pretty sure I got the script from the Makerbot Google group, but it might have been on Thingiverse.
|
# ? Oct 28, 2013 16:26 |
|
Does anyone here have any experience with Sketchup? I am looking to import .obj files into it but the only plugins I can find are pricey. Has anyone seen a free importer, or perhaps know a way to convert them? While my Makerware will open them for printing as they are, I want a way to do some editing in Sketchup.
|
# ? Oct 29, 2013 01:34 |
|
Pez posted:Does anyone here have any experience with Sketchup? I am looking to import .obj files into it but the only plugins I can find are pricey. Has anyone seen a free importer, or perhaps know a way to convert them? While my Makerware will open them for printing as they are, I want a way to do some editing in Sketchup. http://www.fluidray.com/downloads/ (10 second Google search, FluidImporter is free and non-gimped) Sketchup isn't that great for editing polygonal models though. Also, Trimble taking the free version of Sketchup non-commercial only and removing any trace of Sketchup 8's license on the Internet to hide the fact that you can use it for commercial stuff is some bullshit.
|
# ? Oct 29, 2013 01:41 |
|
Obsurveyor posted:http://www.fluidray.com/downloads/ (10 second Google search, FluidImporter is free and non-gimped) I've already tried that, and the version that works with 2013 is indeed gimped and requires a license. Already tried Google, hence me asking here. But thanks. Alternately can anyone suggest something better than Sketchup?
|
# ? Oct 29, 2013 01:46 |
|
Got my 3Doodler. Kind of stupid but its fun.
|
# ? Nov 1, 2013 20:02 |
|
Not an Anthem posted:Got my 3Doodler. Kind of stupid but its fun. How well does the plastic feed through the 3Doodler? I've read some awful things about them not extruding well at all.
|
# ? Nov 2, 2013 23:53 |
|
UberVexer posted:How well does the plastic feed through the 3Doodler? I've read some awful things about them not extruding well at all. It'll hang now and then if you don't give it a clear line of feed but I honestly haven't had a bad time with it.
|
# ? Nov 3, 2013 01:58 |
|
Am I correct that a MendelMax 2.0 would be a good platform for extruder+firmware experimentation? I have a pellet melt pump I wanna play with.
|
# ? Nov 9, 2013 01:29 |
Is the Printrbot simple kit worth the money? I'm going to start getting into 3d printing and I'd rather have something simpler to learn the ropes on before I go building my own Prusa. That, and I figured I could print my own Prusa parts using the Printrbot.
|
|
# ? Nov 9, 2013 01:50 |
|
Mofabio posted:Am I correct that a MendelMax 2.0 would be a good platform for extruder+firmware experimentation? I have a pellet melt pump I wanna play with. MendelMax is a good place to start for any kind of hacking because it's got a crazy strong frame and it is all open source. Do it and let me know how it goes, I'm interested in something like what you've described, but I'm fairly busy with other development.
|
# ? Nov 11, 2013 18:05 |
|
peepsalot posted:I haven't used a makerbot, but my hackerspace has one. Basically all I hear about that one, and also from the only other person I know that has one, is that the extruder stops extruding all the loving time. We also have an UP! Mini (named Shemp), for which we use ABS plastic and it prints beautifully. Since we set it up, I've had maybe two failed prints and one of them was because I let the new spool get tangled. I also love that the UP! software will tell you, in advance, approximately how long a job will take and how much plastic it will use. (Seriously: MakerWare needs to implement that that feature yesterday.)
|
# ? Nov 11, 2013 23:59 |
|
stray posted:(Seriously: MakerWare needs to implement that that feature yesterday.) It did over a month ago Also I'm loving my Flashforge Creator so far. The only trouble I've had so far is leveling the bed, and I think that is mostly my fault and not the printer's.
|
# ? Nov 12, 2013 02:46 |
|
Has anyone actually used those more advanced filaments like laybrick or the timber one, especially on a Replicator 2? I've got one myself and wasnt sure how they would go through the smaller 0.4mm nozzles.
|
# ? Nov 12, 2013 06:55 |
|
I've got some, but haven't tried it out yet, actually. I do have a 0.4mm nozzle though so I can post back when I give it a shot if you like. I did try the glow-in-the-dark stuff and found it to be almost...gritty. I think the phosphorescent stuff doesn't emulsify with the PLA very well. Still prints, but it's a little rough looking.
|
# ? Nov 12, 2013 07:02 |
|
I was asking about the base materials for printing Nylon earlier and after googling the recommendations (Garolite etc.) I noticed that these materials sounded like the old school PCB material Pertinax (basically resin-impregnated cardboard, with standardized name FR-2). So I bought some cheap FR-2 printed circuit boards from ebay (single side, non-drilled) and printing Nylon on those worked beautifully. The prints stuck well at 100 C and released cleanly when cooled down.
|
# ? Nov 12, 2013 17:59 |
|
McSpergin posted:Has anyone actually used those more advanced filaments like laybrick or the timber one, especially on a Replicator 2? I've got one myself and wasnt sure how they would go through the smaller 0.4mm nozzles. My ultimaker also has a 0.4mm nozzle and that wood filament worked fine.
|
# ? Nov 13, 2013 00:23 |
|
I play table top games and am curious if any 3d printers on the market can print reasonably detailed miniatures. (Example: http://static.giantbomb.com/uploads/original/14/142867/2555035-drewcifer.jpeg , maybe an inch tall.) Do I have any options? Should I wait? I'm not in any hurry, it'd just be awesome to print customized minis, if it's possible.
|
# ? Nov 13, 2013 06:03 |
|
If that guy's an inch tall, the detail on that is getting into SLA territory. The only printer on the market in reach of a hobbyist that can reliably hit that resolution is the Form 1, and that's still $3200. A well-calibrated FDM machine capable of 100-micron layers should be able to get close, though, and with a little bit of solvent vapor smoothing you could get something that's at least in the same ballpark. Do consider that you also need to be able to accurately model the characters, or have a design already available, and there will still be finishing work (removing support material) with each guy you print. e: here are representations of what you can expect from, respectively, an average quality FDM, a good quality FDM, and the Form1. The robot is about the size of one of the miniatures you're talking about. Sagebrush fucked around with this message at 06:40 on Nov 13, 2013 |
# ? Nov 13, 2013 06:31 |
|
Anemone posted:I play table top games and am curious if any 3d printers on the market can print reasonably detailed miniatures. (Example: http://static.giantbomb.com/uploads/original/14/142867/2555035-drewcifer.jpeg , maybe an inch tall.) I don't think the hobbyist machines are there yet. To start, I don't think you could produce satisfactory results with FDM. If you had a machine that did 100 micron layers effectively, it would still have a profound loss of detail on something that size (i.e. the chainmail). Maybe the FDM machines that use the .1 mm nozzles and <100 micron layers would produce something that is close but even then, you'll be wrestling with the overhangs and support structures and it will require lots of post-processing. Also, using solvent vapor smoothing will improve the surface finish but remove even more details. Commercial SLA machines could handle miniatures like (see the Shapeways Ultra Detail materials). Hobbyist ones.. maybe.
|
# ? Nov 13, 2013 20:15 |
|
Just saw a KickStarter for a circuit printer. While it isn't 3D it did crib off of some printer designs, and it still has applications in the 3D printer crowd. http://www.kickstarter.com/projects/cartesianco/the-ex1-rapid-3d-printing-of-circuit-boards?ref=home_popular I have a feeling the circuits aren't terribly long-lived or have terrible resistive losses, but still very interesting. I wonder how hard it would be to add their print heads to a traditional FDM head.
|
# ? Nov 13, 2013 23:05 |
|
I just noticed the UP! Mini at $899 http://www.pp3dp.com/index.php?page=shop.product_details&flypage=flypage.tpl&product_id=6&category_id=1&option=com_virtuemart&Itemid=37 A bit under 5" cube build platform (~120mm3) for under a grand with the kind of results I've seen from UP!s in this thread sounds pretty cool. e: Plus I love ABS since I'm always printing for durability and never for prettiness / ornamental / etc. The Eyes Have It fucked around with this message at 00:07 on Nov 14, 2013 |
# ? Nov 14, 2013 00:01 |
|
Not really a 3d printer, but since there's no general CNC thread, this looks kinda neat, though really overpriced in my opinion: http://www.kickstarter.com/projects/1638882643/diwire-the-first-desktop-wire-bender There is a open source version with BOM and everything(actually with more capabilites: 3d bends). My hackerspace is starting to talk about maybe trying to build our own. e: http://makezine.com/projects/diwire-bender/ https://code.google.com/p/diwire/
|
# ? Nov 14, 2013 00:05 |
|
peepsalot posted:Not really a 3d printer, but since there's no general CNC thread, this looks kinda neat, though really overpriced in my opinion: Yeah, I was real sad at how expensive the Kickstarter is. quote:There is a open source version with BOM and everything(actually with more capabilites: 3d bends). My hackerspace is starting to talk about maybe trying to build our own. This is definitely the way to go. You can get a set of the steppers/drivers/power supply you need for like $400 off ebay. I've thought about building one a few times but I really should finish the other kits I have first.
|
# ? Nov 14, 2013 00:35 |
|
New printer for metal clays that can be fired to make solid metal pieces: http://www.indiegogo.com/projects/minimetalmaker-a-small-3d-printer-that-fabricates-with-precious-metal-clay
|
# ? Nov 15, 2013 21:16 |
|
For the next 28(?) hours, there's a contest to win a free Peachy 3d printer (or $120 CAD voucher for backers). http://www.peachyprinter.com/#!blank/c9x8 Photoshop/caption contest for publicity. Sorry for the short notice, just heard. e - ugh, it's an imgur popularity contest. Still though, free printer. Anuvin fucked around with this message at 02:29 on Nov 16, 2013 |
# ? Nov 16, 2013 02:26 |
|
If this has been mentioned already, apologies. There used to be a link checker that told you if a link had already been posted, does it still work like that? "The QU-BD One Up is the world's first production ready 3D printer to break the $200 barrier. It uses industry standard technology and electronics and everything is OPEN SOURCE!" http://www.kickstarter.com/projects/qu-bd/qu-bd-one-up-open-source-production-ready-3d-print A printer for only $200 sounds very tempting. How well would this printer print miniatures like the ones in Sage's post? Sagebrush posted:e: here are representations of what you can expect from, respectively, an average quality FDM, a good quality FDM, and the Form1. The robot is about the size of one of the miniatures you're talking about.
|
# ? Nov 17, 2013 06:22 |
|
Faltion posted:I've had really great results with hairspray so far. It makes the surface contacting the build platform insanely flat, which is something I've never gotten using kapton due to potential bubbles. Does blue tap work with ABS? From what I gathered I thought it was more a PLA thing. We've had great results with ABS sticking to just hairspray too. Blue tape worked ok some of the time, but it wasn't consistent. I'm happy with our Rostock Max delta printer so far, though we've had to replace or upgrade quite a few components to get any quality prints. Each time we replace something, we squeeze a little bit more quality out but we aren't quite there yet. Bridging and temperature controls are our current biggest issues.
|
# ? Nov 17, 2013 07:31 |
|
Good lord, goal of 9k and raised 340k+ so far. As a BTDT buildin' and shippin' things guy I hope they have the planning and management for that to be "break out the champagne, we're celebratin'!" territory. For most people celebratin' would have been back at 20k, and 340k+ is blasted way past celebratin' and wrapped clean through to + whatever hyperventilating into a paper bag would be as an emoticon.
|
# ? Nov 17, 2013 07:35 |
Hopefully they're good. I'm supposed to get mine in February so if someone else backed it and builds it please post about it. If no one has by the time I get mine I'll toss up some pictures of the build process.
|
|
# ? Nov 18, 2013 04:19 |
|
I hope you qu-bd dudes get your stuff. The other kickstarter from them did not go extremely well. Take a look at the comments, for their print head. http://www.kickstarter.com/projects/qu-bd/open-source-universal-3d-printer-extruder-dual-ext/comments Then again, I backed the Peachy printer, so who am I to talk?
|
# ? Nov 18, 2013 19:11 |
|
Has there ever been a successful (not in funding, but in actual delivery) kickstarted 3D printer since Printrbot? Seems like it's the land of vaporware these days.
|
# ? Nov 18, 2013 19:16 |
|
Not kickstarter but that makibox thing is actually starting to ship now as of 2 or 3 weeks ago.
|
# ? Nov 18, 2013 19:17 |
|
Sun Dog posted:If this has been mentioned already, apologies. There used to be a link checker that told you if a link had already been posted, does it still work like that? Literally had my card in my hand but now... Anuvin posted:I hope you qu-bd dudes get your stuff. The other kickstarter from them did not go extremely well. Take a look at the comments, for their print head. Not so sure. Still tempted to pull the trigger. What should i do goons? Edit: gently caress it, went for the two-up even if i won't get it till march Loving Africa Chaps fucked around with this message at 19:45 on Nov 18, 2013 |
# ? Nov 18, 2013 19:32 |
|
|
# ? May 9, 2024 03:42 |
|
Kazy posted:Has there ever been a successful (not in funding, but in actual delivery) kickstarted 3D printer since Printrbot? B9Creator shipped their units.
|
# ? Nov 18, 2013 19:36 |