|
n8r posted:Look into cleaning your fork seals: Thanks. I'll definitely give this a try first.
|
# ? Aug 19, 2014 20:05 |
|
|
# ? Jun 5, 2024 05:35 |
|
epalm posted:I'm paying much closer attention to lever tension and cable slack these days. There should be guidelines in your service manual. Usually a cable clutch can actually keep going backwards (there's an internal spring) a fair bit after the clutch is fully engaged. Generally you want around 1cm of slack at the hand lever.
|
# ? Aug 19, 2014 23:17 |
|
I'm an idiot. Bike was revving up after 15-20 minutes of casual riding. Replace throttle cable (Binding) No Dice. Clean/Sync carbs...No dice Swap air filter/check box...nothing Replace exhaust clamps/gaskets...no dice. Oil change- nope Check choke lever. EDIT: I've been closing as it warms up instead of opening. I feel so stupid. I don't know how. Bright side. Did a ton of maintenance on my bike. SkaAndScreenplays fucked around with this message at 00:55 on Aug 20, 2014 |
# ? Aug 20, 2014 00:46 |
I decided to balance my throttlebodies. To my dismay, I discovered that honda, in their infinite wisdom, have made the TB's completely non-adjustable. The butterflies are solidly bolted to the shaft. The only scope for adjustment is the idle bypass system which basically feeds an extra bit of air from the airbox into each TB via some vacuum lines and a solenoid. No. 2 cylinder is hard bolted to the idle speed adjuster, so you synch the other three to that one, then screw the idle down until it's around 1200. No problem. Unfortunately, this hasn't fixed my rough idle or low-RPM coarseness. I've owned one other 919 with similar mileage and ridden two others, none of them had this. It feels exactly like poorly synchronised carbs on a carby bike: slightly spiking idle and minor, random pops and splutters at very low throttle openings, under 2,500rpm. Power is unaffected, higher rev smoothness is unaffected. My clearances are fine, I've replaced plugs and tested the coils and leads. I can't see what else it can be, it's driving me crazy
|
|
# ? Aug 20, 2014 20:04 |
|
Slavvy posted:poorly synchronised carbs on a carby bike: slightly spiking idle and minor, random pops and splutters at very low throttle openings, under 2,500rpm. Oh. So that's why my 250 burbles.
|
# ? Aug 20, 2014 20:09 |
|
Stupid question ahoy! Yamaha SR 125 (I'm the ninth or tenth owner!) purely for getting some practice in before I step up to something bigger. I'm currently doing about ~125 miles a week on this and will probably keep it till around Feb-March next year. There is a little cracking, but only on the rear tyre. I think the bike might have been stored for a while in someone's conservatory in the sun. Should I be concerned and get some new tyres or is it not worth the expense?
|
# ? Aug 20, 2014 20:55 |
|
Captain Muffin posted:Should I be concerned and get some new tyres or is it not worth the expense? Yes and yes. Bike tires have a finite lifetime, there should be a date code somewhere on the tire - those are probably 5+ years old and are unsafe to ride on.
|
# ? Aug 20, 2014 21:15 |
|
Captain Muffin posted:Should I be concerned and get some new tyres or is it not worth the expense? New tires on a bike are pretty much always worth the expense. You only have two of them, and if either one fails at speed you're in deep poo poo, unlike a car where you probably will just wobble around a bit and can ride it out for a while. Probably the first place you should spend money on an old bike.
|
# ? Aug 20, 2014 21:27 |
|
Christ jesus, that's some serious dry rotting. Get new ones asap.
|
# ? Aug 20, 2014 21:32 |
|
Captain Muffin posted:
How are you even still alive?
|
# ? Aug 20, 2014 21:51 |
|
I shall be doing some tire shopping this weekend! I am a dumbass. I only really noticed it last weekend and then since then its always in the back of my mind when I'm going downhill. Yay for stupid questions.
|
# ? Aug 20, 2014 22:53 |
|
Anyone have an extra speedbleeder dustcap/a suggestion for a replacement? I'm an idiot and already managed to lose one. And they want the full $6 shipping for a ten cent item, so fuuuck that.
|
# ? Aug 21, 2014 01:04 |
|
Autozone usually has a section of random little rubber gaskets and caps for odds and ends. You might be able to find something that fits well enough, if not an exact match. Alternately, they're very similar to the caps used on grease fittings -- you can usually get them at Grainger or other general tool suppliers like that. Should be a physical location you could get them from if you're anywhere near a large city. http://www.grainger.com/product/CAPLUGS-Grease-Fitting-Cap-2PB19
|
# ? Aug 21, 2014 01:12 |
|
That's a great idea! Thanks!
|
# ? Aug 21, 2014 01:30 |
|
Yes, stop asking the thread. Ok. I'm just nervous with my poo poo balance. rizuhbull fucked around with this message at 15:26 on Aug 22, 2014 |
# ? Aug 22, 2014 15:04 |
|
You'll be fine. By the time you get to anything that requires balance, you'll have had enough practice to be comfortable to some degree. My MSF class was the first time I'd ridden any kind of motorcycle and I have always been a clumsy, off-balance, injury-prone person. I had zero issues whatsoever. As long as the bike is rolling forward, it will balance itself with minimal input from you. Slow speed maneuvers are trickier, but again, you'll have a good amount of practice going in straight lines and gentle curves before then. Any kind of glasses will be fine. Work gloves will be fine as long as they're not so clumsy they interfere with your ability to use the controls. You're just going to be puttering around a parking lot at 15 MPH or less.
|
# ? Aug 22, 2014 15:33 |
Alceste posted:You'll be fine. By the time you get to anything that requires balance, you'll have had enough practice to be comfortable to some degree. My MSF class was the first time I'd ridden any kind of motorcycle and I have always been a clumsy, off-balance, injury-prone person. I had zero issues whatsoever. As long as the bike is rolling forward, it will balance itself with minimal input from you. Slow speed maneuvers are trickier, but again, you'll have a good amount of practice going in straight lines and gentle curves before then. This. I'm a clumsy bastard who always bumps into things, drops poo poo and was poo poo at sports as a kid. Bikes are the only time I feel like I'm actually balanced and graceful. They hold themselves up, stop worrying.
|
|
# ? Aug 22, 2014 22:45 |
|
I've been looking at bikes for months now and haven't seemed to find anything more fun than my Bandit so I'm thinking of slowly building up another crazy Bandit in my garage sometime next year or so and was wondering if that's viable? I was thinking of keeping the same setup I have now, meaning a bore kit and GSXR cams, but with the GSXR bottom end so I can keep a clutch basket and gain a sixth gear and not worry about destroying clutches. I also wanna run the entire thing on microsquirt EFI with completely redone suspension (Wilbers rear shock, but not sure on the front forks), with actual warning modules like an oil temp sensor, oil fan, etc. I'm not too interested in doing a turbo build since I'd like some longevity. Guy at a local shop runs his 390lb (with gas) ZZR1200 on standalone and it's making 145whp and like 100+tq and 50mpg all day long and I'm certain he could fabricate a proper trigger setup. Does this seem like a good idea versus just getting something already crazy and stupid?
|
# ? Aug 23, 2014 01:18 |
|
Armchair Calvinist posted:I've been looking at bikes for months now and haven't seemed to find anything more fun than my Bandit so I'm thinking of slowly building up another crazy Bandit in my garage sometime next year or so and was wondering if that's viable? Or you could just buy a Grom/Sumo and have more fun with fewer headaches.
|
# ? Aug 23, 2014 02:55 |
|
HotCanadianChick posted:Or you could just buy a Grom/Sumo and have more fun with fewer headaches. Go for the motard. They're just as expensive but most non-racing ones can actually hang on the highway when you need them to.
|
# ? Aug 23, 2014 03:13 |
|
Armchair Calvinist posted:I've been looking at bikes for months now and haven't seemed to find anything more fun than my Bandit so I'm thinking of slowly building up another crazy Bandit in my garage sometime next year or so and was wondering if that's viable? If you're gonna do this why not start with a GSXR and work it towards Bandit ergos instead
|
# ? Aug 23, 2014 07:28 |
|
Snowdens Secret posted:If you're gonna do this why not start with a GSXR and work it towards Bandit ergos instead Yeah, just take off the plastics and put on Renthal bars and a headlight. A Bandit's just a factory version of what people were doing with their crashed Gixxers anyway.
|
# ? Aug 23, 2014 08:53 |
|
Does anyone make a slim profile/over-the-ear hearing protection that'd fit under a helmet? I've got wonky ears and have tried every version of stuff-inside the ear canal protection, but everything eventually works its way outta my left ear. Plus I'd be more inclined to use it all the time instead of just on longer trips if it just slipped on.
|
# ? Aug 23, 2014 18:01 |
|
Have you tried custom molded earplugs? You can pick them up on amazon for pretty cheap and DIY them.
|
# ? Aug 23, 2014 18:03 |
|
n8r posted:Have you tried custom molded earplugs? You can pick them up on amazon for pretty cheap and DIY them. I haven't, though I'm guessing that's probably what I should try next, since I get the feeling what I'm asking about probably doesn't exist. Thanks Kind of a related question, but does helmet quality have a substantial impact on wind noise? What I've got now is a cheapie 100$ Gmax helmet... Does a spendier helmet typically help isolate external noise?
|
# ? Aug 23, 2014 20:45 |
|
Yes.
|
# ? Aug 23, 2014 20:49 |
|
Yes it absolutely does. I had an HJC IS-MAX originally, and wind noise was pretty bananas. It also didn't fit me that well. I got a Lazer and it's like night and day how much quieter and less buffet-y the nicer helmet is.
|
# ? Aug 23, 2014 20:53 |
|
I bought custom earplugs and they absolutely rock! Foam earplugs would always work their way out or take forever to insert correctly. Radians Custom Molded Earplugs (Red) https://www.amazon.com/dp/B002XULPSQ/ref=cm_sw_r_awd_Dxp-tb0GC1JTB The only problem is when I take my helmet off sometimes one of them will go flying out of my ear.
|
# ? Aug 23, 2014 21:19 |
|
My second replacement speedo cable just broke. It's breaking right at the bottom end where the cable meets the solid metal insert. I'm thinking that it's because when I plug it in, I the cable is bending at a weird angle instead of sticking straight out of the lower plug. Does this sound plausible? Should I be adding grease or something to it before I install? There's a little rubber gasket for the lower end and I don't know if I'm supposed to leave it there either. Basically, please help me. Bike is a 2004 Ninja 250.
|
# ? Aug 23, 2014 22:02 |
|
Silicone earplugs are also a thing. http://www.amazon.com/gp/aw/d/B004CKCX9K/ref=pd_aw_sims_2?pi=SY115&simLd=1 As above, I find they pop out of the helmet sometimes. They can also lose their seal which kind of sucks until the next time you stop for gas. They're worth a try though.
|
# ? Aug 24, 2014 01:24 |
|
Has anyone here tried the mighty plugs? https://earplugsonline.com/ I was just googling around and found a thread by the company in ADV rider.
|
# ? Aug 24, 2014 02:46 |
|
MrKatharsis posted:My second replacement speedo cable just broke. It's breaking right at the bottom end where the cable meets the solid metal insert. I'm thinking that it's because when I plug it in, I the cable is bending at a weird angle instead of sticking straight out of the lower plug. Does this sound plausible? Should I be adding grease or something to it before I install? There's a little rubber gasket for the lower end and I don't know if I'm supposed to leave it there either. Basically, please help me. Bike is a 2004 Ninja 250. From memory the part it screws into slots into place with the screw point pointing up towards the gauge cluster so that the cable kind of goes straight there without any bends aside from a light curve. If its at a weird angle and snapping that part may be in a bit wrong. It kind of clicks into place. Regrease the cable every few months, aside from that you pretty much ignore it.
|
# ? Aug 24, 2014 03:01 |
|
OSU_Matthew posted:Kind of a related question, but does helmet quality have a substantial impact on wind noise? What I've got now is a cheapie 100$ Gmax helmet... Does a spendier helmet typically help isolate external noise? Your bike and your head are big factors here too, I've seen many posts where one person proclaims helmet x to be the quietest ever and another comes along and says it's the noisiest piece of poo poo they've ever worn. Ultimately, the only way to ensure quiet is sort out some ear protection. Relying on more $ = less noise is risky.
|
# ? Aug 24, 2014 03:10 |
|
Lynza posted:Yes it absolutely does. I had an HJC IS-MAX originally, and wind noise was pretty bananas. It also didn't fit me that well. I got a Lazer and it's like night and day how much quieter and less buffet-y the nicer helmet is. I also own a Lazer and love a lot of things about it except that its so goddamn hot. It needs airflow badly. It is fairly quiet and really really comfortable though.
|
# ? Aug 24, 2014 03:43 |
|
MrKatharsis posted:My second replacement speedo cable just broke. It's breaking right at the bottom end where the cable meets the solid metal insert. I'm thinking that it's because when I plug it in, I the cable is bending at a weird angle instead of sticking straight out of the lower plug. Does this sound plausible? Should I be adding grease or something to it before I install? There's a little rubber gasket for the lower end and I don't know if I'm supposed to leave it there either. Basically, please help me. Bike is a 2004 Ninja 250. I don't remember how the speedo drive on the 250 is but on my GS you can move the drive any which way before you tighten the axle. I have to make sure I align it properly before I tightening so I don't have a kink in my cable. If the Ninja is like that you can loosen it up and get the threaded part sticking out in the proper direction so your next cable lasts longer. If it's like my FZR there is a notch in the fork leg that the drive fits into causing the angle is fixed so there's no adjustment.
|
# ? Aug 24, 2014 09:18 |
|
About helmet talk, has anyone else had their helmet, which otherwise fits well, get pushed back so hard at speed (90mph) their nose touches the visor?
|
# ? Aug 24, 2014 12:54 |
|
Here4DaGangBang posted:Your bike and your head are big factors here too, I've seen many posts where one person proclaims helmet x to be the quietest ever and another comes along and says it's the noisiest piece of poo poo they've ever worn. Ultimately, the only way to ensure quiet is sort out some ear protection. Relying on more $ = less noise is risky. Yeah, a lot of noise can be generated if it doesn't fit your head properly, in particular below the chin and around the neck (I noticed this when wearing a thick jumper with a collar and it made things a lot quieter). Honestly I think some pretty cheap helmets would be very quiet if they fit you very well.
|
# ? Aug 24, 2014 13:36 |
|
High Protein posted:About helmet talk, has anyone else had their helmet, which otherwise fits well, get pushed back so hard at speed (90mph) their nose touches the visor? If it can move around like that, it sounds like it doesn't fit well.
|
# ? Aug 24, 2014 14:44 |
|
I have an Icon helmet (I can't tell the model, there's no markings on it), and I like it pretty well. It seems to fit really well and noise doesn't seem to be a problem... the only thing I really need is a replacement tinted visor. Do I have to buy one that is specifically fitted to the helmet, or do they make fairly generic replacements?
|
# ? Aug 24, 2014 15:04 |
|
|
# ? Jun 5, 2024 05:35 |
|
Specific to the helmet, unless you want a stick-on.
|
# ? Aug 24, 2014 16:21 |