|
Do they build 3d renders or actual submarines? I can't tell
|
# ? Nov 12, 2015 07:23 |
|
|
# ? May 30, 2024 13:59 |
|
They don't even have a nuclear-powered model? What a bunch of tryhards.
|
# ? Nov 12, 2015 07:32 |
|
Xlorp posted:Plans, the subject of the picture, rhymes with sans once you dump the serif I said without internets gay, not doubling down on it.
|
# ? Nov 12, 2015 07:44 |
|
TooMuchAbstraction posted:What, you don't mill your house out of a single block of aluminum? The WiFi reception was terrible so I had to move to a home 3D printed out of laser-sintered gypsum.
|
# ? Nov 12, 2015 14:35 |
|
gvibes posted:BEHOLD (I guess I was wrong about the pink) This is amazing, and I love it.
|
# ? Nov 12, 2015 18:49 |
|
Sagebrush posted:They don't even have a nuclear-powered model? What a bunch of tryhards. I'm concerned as to how I can get it out of Austria. They don't exactly have beaches near which I can sit on the deck with gold chains.
|
# ? Nov 13, 2015 01:36 |
|
They email you some rendering until enough checks clear that they can close the company and you never hear from them again.
|
# ? Nov 13, 2015 01:44 |
|
|
# ? Nov 14, 2015 23:51 |
|
Is that mounted by the floor, or the chair rail?
|
# ? Nov 15, 2015 01:18 |
|
Chair rail over brickface paneling. /70s
|
# ? Nov 15, 2015 04:21 |
|
|
# ? Nov 15, 2015 05:17 |
|
I think my bathroom has that same tile. Strangely, I don't think it will ever break my ankles like that stairway would have without that railing.
|
# ? Nov 15, 2015 05:27 |
|
Could that have been retrofitted because people complained of a lack of handrail? Its still dodgy if it is.
|
# ? Nov 15, 2015 07:27 |
Depending on what kind of place that is they may have intended the blind stairs to be more of a sitting area. I assume that's how it gets used regardless, anyway.
|
|
# ? Nov 15, 2015 09:24 |
|
From what I remember, this is in the Bahamas. Which doesn't surprise me one bit, getting things done over there is nearly an exercise in futility. Let alone getting it done right.
|
# ? Nov 15, 2015 12:32 |
|
My middle school had part of the stairs blocked off as a seating area, because students would be sitting there anyway. They got slapped on the fingers by the fire deparment though because you're not allowed to put an obstacle like that in the middle of an evacuation route.
|
# ? Nov 15, 2015 12:58 |
I want to see people go up the right side then awkwardly come back down and go up the left side
|
|
# ? Nov 15, 2015 23:19 |
|
MullardEL34 posted:I recently became the Tenant of a 8400Sq. Ft. office building that served as the Headquarters of a Local NE Ohio Newspaper from the late 1870's to September of 2012. The oldest part of the building was built in 1858, by a Farrier that leased horses and wagons to the federal government for the Cleveland-Ravenna and Mentor-Ravenna mail routes. It did a short stint as a mortuary/funeral parlor in the early 1870's. The Ravenna Republican newspaper moved in the the late 1870's. Things are coming along... MullardEL34 fucked around with this message at 12:14 on Nov 16, 2015 |
# ? Nov 16, 2015 12:10 |
|
MullardEL34 posted:Things are coming along... That was my favourite part of Half-Life
|
# ? Nov 16, 2015 13:43 |
|
The floor textures are not rendering correctly, man.
|
# ? Nov 16, 2015 15:00 |
|
Manslaughter posted:I want to see people go up the right side then awkwardly come back down and go up the left side I like how they made the rail a raptor fence too, so you can't just duck under it. It's around the bottom or over the top
|
# ? Nov 16, 2015 19:45 |
|
MullardEL34 posted:Things are coming along... The inconsistent floor patterning is a crime against humanity that cries out for retribution.
|
# ? Nov 16, 2015 20:37 |
Pigsfeet on Rye posted:The inconsistent floor patterning is a crime against humanity that cries out for retribution. The more you look, the more texture mapping mistakes you see, they just keep going!
|
|
# ? Nov 16, 2015 20:48 |
|
Bad Munki posted:The more you look, the more texture mapping mistakes you see, they just keep going! All I see is a T-1000 camouflage fail.
|
# ? Nov 16, 2015 23:51 |
|
Horses aren't quite as autistic as your average somethingawful goon, so I don't think they were too bothered.
|
# ? Nov 17, 2015 01:07 |
|
|
# ? Nov 17, 2015 20:03 |
|
What's the problem? That's perfectly legal. In Moldova, maybe.
|
# ? Nov 17, 2015 20:05 |
|
Yeah, great, nice picture without any conte- wait, what's that brown turd-looking thing on the right?
|
# ? Nov 17, 2015 20:59 |
|
Has there ever been a time in the US where hardwood was used for studs, or where "soft" wood was significantly harder? At some point in the lifetime of my 110 year old house someone framed in a little workshop in the basement with 2x4 studs 4 foot on center and then 4x8 plywood attached to that. I was attaching some brackets to it and I had a hell of a time driving the screws in with my plug-in drill. The directions said to pre-drill the holes but I said "lol pine" and drove them in with no pilot. After the first bracket I went with predrilling (3/32 inch) and even with that I really had to press in and the drill bit got pretty hot. I also swear the drill shavings smelled the same as what oak smells like when you cut it. Is it possible I have oak studs in my basement?
|
# ? Nov 17, 2015 21:55 |
Older pine was much denser because it grew slower. They also tended to dice the entire tree up into whatever dimensional lumber was being made that day so you ended up with 2x4s made of even tougher heartwood. Now the mills laser scan each trunk to optimize the cuts based on predicted market is prices for various dimensions of lumber. There's a bit of hushed background talk in the softwood lumber industry about the possibility that the new horticultural methods are making the trees grow too quickly and that the lumber may not meet strength standards as a result.
|
|
# ? Nov 17, 2015 22:30 |
|
Also, your 110 year old house may have been built out of whatever trees grow locally.
|
# ? Nov 17, 2015 22:44 |
|
FISHMANPET posted:Has there ever been a time in the US where hardwood was used for studs, or where "soft" wood was significantly harder? At some point in the lifetime of my 110 year old house someone framed in a little workshop in the basement with 2x4 studs 4 foot on center and then 4x8 plywood attached to that. I was attaching some brackets to it and I had a hell of a time driving the screws in with my plug-in drill. The directions said to pre-drill the holes but I said "lol pine" and drove them in with no pilot. After the first bracket I went with predrilling (3/32 inch) and even with that I really had to press in and the drill bit got pretty hot. I also swear the drill shavings smelled the same as what oak smells like when you cut it. Is it possible they used local woods in non standard sizes? Or it is just old pine that has held up well.
|
# ? Nov 17, 2015 22:46 |
|
Shifty Pony posted:There's a bit of hushed background talk in the softwood lumber industry about the possibility that the new horticultural methods are making the trees grow too quickly and that the lumber may not meet strength standards as a result. That isn't just a possibility, it's almost a certainty. Half of the lumber we get in at the yard is checked down the middle from what I'm certain is growing them fast, and drying them fast. The other half is crooked. We had to try to switch suppliers because they couldn't send us any 2x12x8s that weren't 95% junk. You shouldn't be able to pick a piece of lumber out of a fresh pile, and have it break in two right off the bat.
|
# ? Nov 17, 2015 22:49 |
|
Shifty Pony posted:There's a bit of hushed background talk in the softwood lumber industry about the possibility that the new horticultural methods are making the trees grow too quickly and that the lumber may not meet strength standards as a result. I think this is part of the reason the industry is looking to things like VersaLam for some applications where strength or straightness is of paramount concern. Of course, each stud costs like 3x as much, but they're great for framing out doors/windows or on corners.
|
# ? Nov 17, 2015 22:52 |
|
"Hardwood" and "Softwood" are distinguished by whether the tree is a Gymnosperm or Angiosperm. Many of the common hardwoods are harder than the common softwoods, but some softwoods (like Yew) are harder than most hardwoods, and the softest woods (such as Balsa) are hardwoods. And as mentioned, old-growth and/or heartwood, or even just knots, can give you quite hard specimens from wood species that are typically soft.
|
# ? Nov 17, 2015 22:56 |
I wonder what future consequences there will be for using quick-grown trees as infrastructure?
|
|
# ? Nov 17, 2015 22:57 |
|
Finger jointed studs seem like a great option for straighter lumber as well; I'm surprised they aren't easier to find.
|
# ? Nov 17, 2015 23:04 |
|
Zhentar posted:Finger jointed studs seem like a great option for straighter lumber as well; I'm surprised they aren't easier to find. They're incredibly straight and work well until you drive a nail/screw into the joint and the whole thing splits in half lengthwise.
|
# ? Nov 17, 2015 23:06 |
|
Ha, that could be a bit of a down side.
|
# ? Nov 17, 2015 23:49 |
|
|
# ? May 30, 2024 13:59 |
|
neogeo0823 posted:Yeah, great, nice picture without any conte- wait, what's that brown turd-looking thing on the right? I'm pretty sure it's just backing paper for the plasterboard with a bit of plaster still stuck to it? I think it's the wiring that's scary here... E: Magnus Praeda posted:They're incredibly straight and work well until you drive a nail/screw into the joint and the whole thing splits in half lengthwise. I don't think there's any particular reason that a well-made finger joint scarfed board would be more likely to split than a non-jointed one?
|
# ? Nov 18, 2015 00:12 |