|
Just Google "nutbuster XXL", I swear it won't get you fired... Edit: XL is the size I got but the XXL one sounds... Pornier
|
# ? Dec 10, 2017 17:15 |
|
|
# ? May 16, 2024 18:57 |
|
kastein posted:House has working kitchen ceiling lamps and living room ceiling lamp for the first time ever, and will have living room outlets working tomorrow. This is weird, I keep putting my headlamp on from force of habit but I don't need it inside anymore, except in the dining room and basement. At this rate you'll start using the door to exit the house, instead of sledgehammering a hole in the wall and exiting through that.
|
# ? Dec 10, 2017 18:06 |
|
Seat Safety Switch posted:At this rate you'll start using the door to exit the house, instead of sledgehammering a hole in the wall and exiting through that. Excuse me, we haven't done that since 2016! (When I replaced the wall in the kitchen that's I'd previously replaced and put a door in, but put a window in this time.)
|
# ? Dec 11, 2017 00:22 |
|
kastein posted:Just Google "nutbuster XXL", I swear it won't get you fired... Nut Blaster XL
|
# ? Dec 11, 2017 15:38 |
|
You're right. Whoops As of last night the living room outlets, USB charging ports, and switched outlets for floor lamps work. Hoping to get the garbage disposal and front porch lighting circuits done tonight.
|
# ? Dec 14, 2017 18:09 |
|
Seat Safety Switch posted:At this rate you'll start using the door to exit the house, instead of sledgehammering a hole in the wall and exiting through that. He didn't have to sledge anything. Most of the walls lifted up like garage doors thanks to rot and carpenter ants.
|
# ? Dec 15, 2017 03:10 |
|
Yeah pretty much Holy poo poo, the master bedroom has a door again. This is the most complete this room has been since around 2010 or 2011, when I started demolition while doing the new roof and caved in its ceiling.
|
# ? Dec 31, 2017 07:13 |
|
Heat, interior lighting, solid walls... Next you'll want things like "wifi" or "chairs." Such luxuries.
|
# ? Dec 31, 2017 16:28 |
|
I'm a goon, this joint has had WiFi since about a week after I moved in, back in 2011 Priorities.
|
# ? Dec 31, 2017 18:03 |
|
kastein posted:I'm a goon, this joint has had WiFi since about a week after I moved in, back in 2011 When I showed my friends around my new house which is under a lesser-than-yours-but-still significant amount of renovation, the first comment was “I’m glad to see nerd-station-one is operational already.”
|
# ? Dec 31, 2017 20:13 |
|
I just figured with your typical hardware/UI interface issues, you'd be hard wired instead of wireless to start.
|
# ? Jan 1, 2018 04:44 |
|
Beverly Cleavage posted:I just figured with your typical hardware/UI interface issues, you'd be hard wired instead of wireless to start. With all the spontaneous demolition that has gone on in that house, running (yet more) wires through the walls seems counterproductive. Beach Bum fucked around with this message at 07:46 on Jan 1, 2018 |
# ? Jan 1, 2018 07:43 |
|
Beach Bum posted:spontaneous demolition Now that's a great phrase. Almost right up there with "lithobraking". (Amusingly, spellcheck is perfectly happy with the word lithobraking.)
|
# ? Jan 1, 2018 08:30 |
|
Beach Bum posted:With all the spontaneous demolition that has gone on in that house, running (yet more) wires through the walls seems counterproductive. Too much risk of them becoming temporary structural support tbh.
|
# ? Jan 1, 2018 11:33 |
|
Darchangel posted:Now that's a great phrase. Almost right up there with "lithobraking". "Structural lithotripsy." Edit: "Braking," not "breaking." Hurrr. But it let me check -- spellcheck SUGGESTED "lithobraking" to me.
|
# ? Jan 1, 2018 14:37 |
|
I found the "through the walls" bit hysterical. that comes AFTER the walls start reappearing.
|
# ? Jan 1, 2018 18:32 |
|
Beverly Cleavage posted:I just figured with your typical hardware/UI interface issues, you'd be hard wired instead of wireless to start. I'm a late adopter of many technologies (I like everyone else to find all the horrible bugs, compatibility issues, and security holes the hard way before I start using it, so I can find a bunch more anyways, just after support isn't available anymore) and actually put 1in conduit and duplex boxes to most walls of most rooms for this reason. I can run any kind of comms, audio, DC power, etc etc cabling I want anywhere in this house without pulling drywall back down. That being said, with how cheap esp8266 boards are, I'm debating abandoning wired even for hobby stuff. A/V and high speed networking I'd rather be able to pull cable. But I'm working an esp8266 board into one of my projects simply so I don't have to put a user interface or rs232/USB interface on it for configuration. It's cheaper than a waterproof connector and a cable, and means no holes in the enclosure. Stained the master bedroom door last night, almost got high off the stain fumes. 2/10 would not huff stain fumes again
|
# ? Jan 1, 2018 19:16 |
|
kastein posted:Stained the master bedroom door last night, almost got high off the stain fumes. 2/10 would not huff stain fumes again I'm so happy to see this thread back up and active, it's one of my favorites. Now that my choices are "get poo poo done" or "change diapers" I might actually tear into some of the projects that need doin' right now.
|
# ? Jan 1, 2018 20:04 |
|
Past few months worth of pics I never posted: https://www.youtube.com/watch?v=NcrhgxRkXJE , Garvin Industries is my favorite electrical wiring products manufacturer... They had the 4-11/16 square 2in deep duplex mud ring I needed to put on this box so I could pretend I didn't forget I was going to put 2x2 on the studs, or bend another piece of conduit. And they sell directly to customers on an internet site so I can be a nerd and just order what I need instead of going to a store. Oh, and unlike Home Depot and Amazon, I could order one instead of a box of a dozen. Oops. This thing means business. That wire nut is wrecked, the wires are almost poking out the tip... I really need to get my rear end in gear. I've been slacking hardcore on the house for some time now. That being said, I managed to accomplish this massive amount of framing over a 4 day weekend: Only a couple more sticks of framing, then I can do the fireblocking in the closets, wire them, vapor barrier, and insulate them. kastein fucked around with this message at 23:23 on Jan 2, 2018 |
# ? Jan 2, 2018 23:21 |
|
Garvin Industries sounds like a useful company to know about. Thanks for the tip.
|
# ? Jan 3, 2018 01:12 |
|
Check out their clearance section, too. I'm nowhere near ready to install the actual furnace yet, but 60 cents each for the red shutoff cover plates? Yes please. They have stainless steel junction boxes and stuff too... I know what I'm putting in the shop, when I build one.
|
# ? Jan 3, 2018 01:19 |
|
I forgot to post this weeks ago when it happened. This is the rough opening for the fold down attic stairs. When I bought the place it had a tiny useless attic trapdoor, and when I tore all the second floor walls down, replaced the rafters, and put them back up in 2012-2013, I entirely forgot that I wanted to put up a folding stair, so I built the spare bedroom wall way too close to the only set of rafters worth using for such a thing and then put a ton of wiring in the way. I've been dreading undoing that all and framing it out for the stairs ever since then. It finally got to the point where I couldn't make progress on anything around it in the second floor hallway without facing the demon though, so I did it. It really wasn't as bad as I was expecting and I wish I'd dealt with it sooner. Oh well, it's done now.
|
# ? Jan 23, 2018 21:27 |
|
One of the first things I did after I bought my house was put in attic stairs. Built in 1964, bought in 2000, and no one had put in stairs in all that time. There was one little (I mean tiny) hatch in the garage, where the roof was lower, and difficult to get to the rest of the space, so I put a set in the hall. At some point I should gasket the hatch and/or build a Styrofoam insulation box (for summer heat in my case). Also decked the attic area immediately around the stairs. Probably should at leas deck a path to the air handler manifold. It's a pain getting over/under the ducts while struggling not to step through the ceiling. Also need to re-insulate the rigid ducts, but gooooooood I don't want to do that.
|
# ? Jan 24, 2018 00:27 |
|
I need to replace my attic stairs. The original ones are still in decent enough condition but they're just plain flimsy by design, with a 250lb max load. I don't like climbing ladders in the first place, and I especially don't like flimsy wooden ladders that aren't even rated to hold me, let alone anything I'm hauling up.
|
# ? Jan 24, 2018 00:58 |
|
Do you happen to have a master album of these pictures somewhere? All of the original ones from the beginning of the thread are long gone.
|
# ? Jan 24, 2018 01:07 |
|
Darchangel posted:One of the first things I did after I bought my house was put in attic stairs. Built in 1964, bought in 2000, and no one had put in stairs in all that time. There was one little (I mean tiny) hatch in the garage, where the roof was lower, and difficult to get to the rest of the space, so I put a set in the hall. I have one of these Owens-Corning 541799 R-10 Attic Stairway Insulator, for Openings Up To 24.5 by 54-Inch https://www.amazon.com/dp/B002SYP8SA/ref=cm_sw_r_cp_apa_e28zAbGFD736E And I like it better than the zippered ones, because it moves completely out of the way if you have attic storage. It may not be "sealed" because the bottom of the tent is just sitting, but it seems to make a big difference. Installation is simply setting it in place which can't get any easier.
|
# ? Jan 24, 2018 01:07 |
|
Just don't put your stairs in there too securely, you might need to pull them back out if your're gonna squeeze an air handler and ductwork up there Darchangel posted:Also need to re-insulate the rigid ducts, but gooooooood I don't want to do that. Ductwrap is a product of the devil and this is something you should 10000000% hire out to somebody else. Trust me, being covered in sweat, in an attic that doesn't breath, while working with fibreglass is the worst thing in the world.
|
# ? Jan 24, 2018 01:59 |
|
H110Hawk posted:Do you happen to have a master album of these pictures somewhere? All of the original ones from the beginning of the thread are long gone. I don't I'm pretty sure those aren't gone, per se, just broken links because Facebook used to allow hotlinking (in fact they had a share external button that gave you a direct jpeg URL) and then one day they woke up and went "lol oh nevermind" and not only moved all the images around but stopped allowing hotlinking. I still haven't gotten around to figuring out which image goes where and updating the IMG tags. E: yeah confirmed this theory, the IMG tags all point at old FB image CDN URLs kastein fucked around with this message at 04:16 on Jan 24, 2018 |
# ? Jan 24, 2018 04:14 |
|
kastein posted:I don't I'm pretty sure those aren't gone, per se, just broken links because Facebook used to allow hotlinking (in fact they had a share external button that gave you a direct jpeg URL) and then one day they woke up and went "lol oh nevermind" and not only moved all the images around but stopped allowing hotlinking. Yea facebook now makes their image links expire after some amount of time, and I honestly don't blame them.
|
# ? Jan 24, 2018 18:50 |
|
That was like 3 FB image URL encodings after this all broke, I've just been too lazy to go back and fix it.
|
# ? Jan 24, 2018 21:44 |
|
angryrobots posted:I have one of these Yeah, basically one of those. I've seen folks just build a box out of styrofoam insulation board, which would probably be a lot cheaper, provided I could get a 4x8 sheet of the stuff home (currently do not have a truck, suv, or wagon, sadly.) Thanks for the link. May take easy over absolute $$. ExplodingSims posted:Just don't put your stairs in there too securely, you might need to pull them back out if your're gonna squeeze an air handler and ductwork up there Would like to hire out if I can afford it. Need to finish paying off the credit union for the $5400 plumbing job from a few months ago, first, though.
|
# ? Jan 25, 2018 01:26 |
|
Darchangel posted:Yeah, basically one of those. I've seen folks just build a box out of styrofoam insulation board, which would probably be a lot cheaper, provided I could get a 4x8 sheet of the stuff home (currently do not have a truck, suv, or wagon, sadly.) Thanks for the link. May take easy over absolute $$. Just measure what you need and cut it in the parking lot.
|
# ? Jan 25, 2018 01:57 |
|
devicenull posted:Just measure what you need and cut it in the parking lot. This. Utility knife'll get you most of the way there, then a good knee to break it. Then ratchet strap to the top of the car. Bring a friend, you'll want someone to hold pieces in place while you fart around with straps.
|
# ? Jan 25, 2018 03:13 |
|
ExplodingSims posted:Just don't put your stairs in there too securely, you might need to pull them back out if your're gonna squeeze an air handler and ductwork up there Yeah fiberglass and poo poo in a closed space is miserable. It's definitely a winter project. Good point on the stairs. We'll probably not put them in for years, I just needed the framing done and ready for them so I could build other things around it.
|
# ? Jan 25, 2018 14:45 |
|
devicenull posted:Just measure what you need and cut it in the parking lot. TheNothingNew posted:This. Utility knife'll get you most of the way there, then a good knee to break it. Then ratchet strap to the top of the car. Bring a friend, you'll want someone to hold pieces in place while you fart around with straps. I like the way you guys think. I also just realized that, while my Crown Vic doesn’t have fold down seats (I wish. It could haul some poo poo if it did), my AE86 coupe does. Can’t do 4x8, but I bet I can do 2x8, times 2, with the back and front passenger seats folded down.
|
# ? Jan 25, 2018 17:58 |
|
if you actually do need to bring home a bunch of 4x8, like for a different project I mean, home depot rents pickup trucks and vans by the hour.
|
# ? Jan 25, 2018 21:37 |
|
Leperflesh posted:if you actually do need to bring home a bunch of 4x8, like for a different project I mean, home depot rents pickup trucks and vans by the hour. And if it's rented out around $30 gets you a f150 from uhaul for the day. ($20 plus miles tax and gas.)
|
# ? Jan 25, 2018 22:35 |
|
Leperflesh posted:if you actually do need to bring home a bunch of 4x8, like for a different project I mean, home depot rents pickup trucks and vans by the hour. Oh, I know, I've used it for precisely that, before I had something with a trailer hitch and access to a Harbor Freight trailer. Pretty good deal at $20 for 75 minutes. I live like 5 miles from a home Depot. I just don't want to rent a truck or borrow the trailer for one sheet of styrofoam. For this, I miss my Cherokee. Still glad I sold it to get the Crown Vic, though. It's better in every way except cargo space.
|
# ? Jan 25, 2018 23:31 |
|
Fair enough, yeah. I've spoken to numerous people who believe they "need" a pickup truck or SUV because they buy sheet goods at home depot twice a year, and I like to point out that they can spend $50 a year on renting for that and otherwise get a vehicle that actually suits their needs for the rest of the time. It usually doesn't work, because usually they actually just want a truck and use their occasional trips to Home Depot as rationalization, but every once in a while it's like a lightbulb going off.
|
# ? Jan 25, 2018 23:35 |
|
|
# ? May 16, 2024 18:57 |
|
Leperflesh posted:Fair enough, yeah. I've spoken to numerous people who believe they "need" a pickup truck or SUV because they buy sheet goods at home depot twice a year, and I like to point out that they can spend $50 a year on renting for that and otherwise get a vehicle that actually suits their needs for the rest of the time. Yep, that's pretty much why I don't have a pickup now. I don't have enough need for it to justify the space and upkeep costs (insurance reg, etc.) When I have a shop and a few acres, I'll rethink it.
|
# ? Jan 26, 2018 00:12 |