|
They make a drill bit called a socket saver to remove plastic fittings from a hub. You could give it a shot, which would allow you to glue in a short run of pipe to connect another wye with a clean out on the end. https://www.youtube.com/watch?v=KQGssYM5C2M EDIT: Make sure you ream the end after using the bit, unlike the rear end in a top hat in the video above. BubbaGrace fucked around with this message at 15:21 on Apr 22, 2018 |
# ? Apr 22, 2018 15:17 |
|
|
# ? Jun 5, 2024 23:50 |
|
Pooh goes downhill. Branching off the clean-out seems like a great way to get all the waste from the rest of the house into your basement. Best way, I think, would be to cut out one your wyes and replace it with a double wye. In your case it looks like you'll need cut above the 22, meaning you'll need a double wye, three repair couplings, a new 22 elbow, and a few scraps of straight PVC of the correct diameter. Double wye: https://www.lowes.com/pd/Charlotte-Pipe-3-in-Dia-PVC-Double-Wye-Fitting/3358078
|
# ? Apr 23, 2018 19:28 |
|
HycoCam posted:Pooh goes downhill. Branching off the clean-out seems like a great way to get all the waste from the rest of the house into your basement. Best way, I think, would be to cut out one your wyes and replace it with a double wye. In your case it looks like you'll need cut above the 22, meaning you'll need a double wye, three repair couplings, a new 22 elbow, and a few scraps of straight PVC of the correct diameter. As a service guy, I want to go on record right now by saying "I hate you". Double wyes, tees and crosses are the devil. How is he going to get the waste water in his basement? If the building drain penetration through that wall has proper pitch, tying on the to where the current clean out is should be fine. The only way it would get into his basement is if he has a building sewer back up some where in the yard. To prevent this he could easily install a back-water valve in-line on his new drain pipe from the water closet. Back water valves are actually required on any basement fixture branch by code as of April 2017 in my state. BubbaGrace fucked around with this message at 21:04 on Apr 23, 2018 |
# ? Apr 23, 2018 21:01 |
I did mention it was a macerator toilet, but maybe that doesn't necessarily imply the full situation: the toilet in question is specifically designed to go below the level of the rest of the sewer. It grinds your beefy shits up, and then pumps them uphill. Supposedly the one in question also has an input for other waste water, so he'll be able to drain a shower through it. Toilet will chew turds, and then pump the paste up well above the level of the cleanout, where it can fall back downhill and exit the premises through the usual mechanism. Because of the unique qualifications of the toilet, I'm going to go out on a limb and say it has back flow prevention. Otherwise, that'd make for a remarkable bidet-type situation. ))<>((
Bad Munki fucked around with this message at 04:46 on Apr 24, 2018 |
|
# ? Apr 24, 2018 04:41 |
|
Macerator pump will have like a 2" dump tube. Just splice a wye into a piece of straight pvc. Don't mess with the cleanout. Bad Munki posted:Maserati toilet Unrelated question. I'm shopping for a tankless water heater, and loving things are expensive. Does anyone know where a good deal could be found?
|
# ? Apr 29, 2018 02:01 |
|
Nitrox posted:Unrelated question. I'm shopping for a tankless water heater, and loving things are expensive. Does anyone know where a good deal could be found? You don't want a good deal. You want a good unit, or you will absolutely hate it. I know several people with Naviens - they seem to be the go-to for a quality unit these days. Also - install matters. A lot. You want someone who knows how these things work.
|
# ? Apr 29, 2018 18:57 |
|
My sink faucet seems to squeal. I turned off hot/cold and it still makes the sound regardless so I guess it's the faucet? I can't seem to find a way to take the handle off if that's even possible. I can't also find a manufacturer to see if its still covered under warranty. Any suggestions or ideas? Link/Video of sound: https://www.dropbox.com/s/u8kikk2i1vmbzge/VID_20180430_120748.mp4?dl=0
|
# ? Apr 30, 2018 22:05 |
|
Is the video working for anyone else?
|
# ? Apr 30, 2018 22:14 |
|
Are you using the SALR extension? Maybe try this link in a browser window: h**ps://www.dropbox.com/s/u8kikk2i1vmbzge/VID_20180430_120748.mp4?dl=0
|
# ? Apr 30, 2018 22:25 |
|
lol internet. posted:I can't seem to find a way to take the handle off if that's even possible. Behind the little yin/yang hot/cold symbol is a set screw to remove the handle.
|
# ? May 1, 2018 00:38 |
|
After seeing a couple things recently about "sacrificial anodes" in hot water heaters, I figured it's probably time to check on mine. The unit was installed in 2011 (I bought the house in 2015,) and knowing what I do about the previous home-owner, there's no way he replaced it before I bought it. I just don't know where the darn thing is. Here's the top of the thing: Here's the part in the manual describing it: So...does that mean it's under/part of the hot water outlet here?:
|
# ? May 1, 2018 15:58 |
|
DrBouvenstein posted:So...does that mean it's under/part of the hot water outlet here?: Yep! Ain't that a bitch? The method for getting them out is an even worse bitch if you don't have enough ceiling clearance to pull it straight up and out. It basically goes 1. pull up rod as far as you can 2. clamp bottom of rod with vice grips 3. cut through rod 4. repeat until rod is completely out. The vice grips are so you don't drop the rod in the tank. 7 years old should still be good. You probably got a few more years. Still, when you get around to it, you could probably use some dielectric unions. edit: they make replacement anode rods that go in easier. They're kinda shaped like old school sausage links. They got the anode split up along a stainless steel braided cable so it's flexible. kid sinister fucked around with this message at 19:59 on May 1, 2018 |
# ? May 1, 2018 19:54 |
|
Is this where to ask about yard irrigation equipment or is there a better place?
|
# ? May 3, 2018 23:24 |
|
DrBouvenstein posted:After seeing a couple things recently about "sacrificial anodes" in hot water heaters, I figured it's probably time to check on mine. The unit was installed in 2011 (I bought the house in 2015,) and knowing what I do about the previous home-owner, there's no way he replaced it before I bought it.
|
# ? May 4, 2018 01:24 |
|
I saw a puddle around the salt tank in my basement and when I inspected it, the water wasn't salty and there was a ton of condensation on the tank so I figured oh hey neat condensation. Well 4 days later it's still there, same size, so I investigate again and low and behold a drop comes from above. 5 year old house, WaterPEX by Watts piping, looks like a pinhole leak in the middle of a span. All I can find online is that this isn't supposed to happen with PEX, but what I really want to know is it a ticking time bomb to a large crack or failure that is going to spew water everywhere, or does that not really happen? I can't find anything on defective product, so I guess my option is to tape it until I learn/pay someone to put a proper repair in. Thoughts?
|
# ? May 4, 2018 03:30 |
|
So I have a periodic sewer smell coming from somewhere, but I can't tell where. We've flushed and ran water down all possible sinks and drains, so I don't think there's a dry P-trap somewhere that would be letting the smell out. Is the next step to check the vent? What do I do besides look at it and go "yep it's there"?
|
# ? May 14, 2018 23:45 |
|
Frinkahedron posted:So I have a periodic sewer smell coming from somewhere, but I can't tell where. We've flushed and ran water down all possible sinks and drains, so I don't think there's a dry P-trap somewhere that would be letting the smell out. Is the next step to check the vent? What do I do besides look at it and go "yep it's there"? Sometimes there can be a smell coming from the the hot water similar to a sewage smell. The sulfur like smell is from the magnesium/aluminum anode rode reacting with the hydrogen to create a sulfate, which has a farts smell. If the water heater is less than 10 years old and doesn't leak I would recommend having the anode rod replaced and the tank flushed. This is all based on if you can isolate the smell down to only when the smell is happening when the hot water is running through the fixtures. BubbaGrace fucked around with this message at 00:40 on May 15, 2018 |
# ? May 15, 2018 00:33 |
Any of your toilets loose on their flange bolts?
|
|
# ? May 15, 2018 01:22 |
|
BubbaGrace posted:Sometimes there can be a smell coming from the the hot water similar to a sewage smell. The sulfur like smell is from the magnesium/aluminum anode rode reacting with the hydrogen to create a sulfate, which has a farts smell. If the water heater is less than 10 years old and doesn't leak I would recommend having the anode rod replaced and the tank flushed. This is all based on if you can isolate the smell down to only when the smell is happening when the hot water is running through the fixtures. Hmm, haven't noticed it correlating with hot water, but I'll see if that shakes anything out. Bad Munki posted:Any of your toilets loose on their flange bolts? Negative.
|
# ? May 15, 2018 01:57 |
|
The hot water in my apartment smells like farts for the first gallon or so and now I know why.
|
# ? May 15, 2018 02:00 |
|
Is there anything about this picture that says to you "Yes, it's obvious that X and Y are the knobs you turn to de-winterize your irrigation system"? Or is it not that simple? (nothing is ever that simple) jackpot fucked around with this message at 05:13 on May 15, 2018 |
# ? May 15, 2018 05:04 |
|
I'd turn the vertical red valve a quarter turn 1st. The horizontal one a quarter turn 2nd.
|
# ? May 15, 2018 05:24 |
|
HycoCam posted:I'd turn the vertical red valve a quarter turn 1st. lol
|
# ? May 15, 2018 06:01 |
|
Frinkahedron posted:So I have a periodic sewer smell coming from somewhere, but I can't tell where. We've flushed and ran water down all possible sinks and drains, so I don't think there's a dry P-trap somewhere that would be letting the smell out. Is the next step to check the vent? What do I do besides look at it and go "yep it's there"? Do you have basement floor drains?
|
# ? May 15, 2018 06:03 |
|
HycoCam posted:Do you have basement floor drains? I do! And it turns out, this may have been it, missed it the first time around. We poured a gallon of water down it last night and it's been 24 hours since the smell, holding onto hope for the next few days
|
# ? May 16, 2018 02:07 |
|
Do you guys use hoses like these where you are? And what they are called if so. http://www.biltema.se/sv/Bygg/VVS/PEM-plastrorsystem/PEM-slang-2000031784/ PEM hose is what we call them but I have not found anything in english. Used for cold water piping mainly. I wanted to go look for some cheaper couplings and stuff online but it's a bit difficult when you don't know what to search for.
|
# ? May 19, 2018 06:14 |
|
His Divine Shadow posted:Do you guys use hoses like these where you are? And what they are called if so. PEX pipe
|
# ? May 19, 2018 12:34 |
|
No it's not PEX, we got PEX hose here too and that's got the same name. But I went and bought the stuff I needed locally anyway so I could have it all done today. And now it's 21:00 and it's not going to be done for days since I got one wrong part
|
# ? May 19, 2018 19:11 |
|
His Divine Shadow posted:Do you guys use hoses like these where you are? And what they are called if so. Is that to hook up an air gap from a Dishwasher?
|
# ? May 22, 2018 04:40 |
|
No PEM hoses, apparently polyethylene or something like that are used for underground water mains and outdoor cold water lines.
|
# ? May 22, 2018 07:09 |
|
https://www.homedepot.com/p/1-in-x-100-ft-IPS-100-psi-NSF-Poly-Pipe-X2-1100100/205903465 Polyethylene pipe is I think what you are asking about.
|
# ? May 22, 2018 07:15 |
|
HycoCam posted:https://www.homedepot.com/p/1-in-x-100-ft-IPS-100-psi-NSF-Poly-Pipe-X2-1100100/205903465 Ya but that Poly pipe isnt allowed for water mains, that is some irrigation bullshit.
|
# ? May 23, 2018 01:42 |
|
Well pipe: https://www.lowes.com/pd/ADS-1-in-x-100-ft-160-PSI-Plastic-Coil-Pipe/3514728 Same pipe, but higher PSI. Well poly typically ranges from 1" to 1.5" and 160psi to 250psi. Which pipe you want to use is going to be a factor of your well pump and your well depth (and pressure tank and the water level below the ground.)
|
# ? May 23, 2018 03:20 |
|
One out of my outdoor hose spigots has a plastic connector to quickly screw and unscrew hoses, and the whole outer barrel rotates freely. I want to remove it. It leaks like crazy when I turn the valve. I don't know what the hell to call it. Inside the unit is a spring loaded pin that I can pull down, and when I release that it returns up inside the whole thing. There's no obvious way for me to take the whole thing off, unless this is a one-piece thing that includes the valve itself. Here's some photos. Off: On, and leaking out of the top: Any thoughts? {edit} It appears to be a Watts 8P "non-removable" anti-tamper thermoplastic connector. gently caress VERTiG0 fucked around with this message at 23:59 on May 23, 2018 |
# ? May 23, 2018 23:54 |
|
VERTiG0 posted:One out of my outdoor hose spigots has a plastic connector to quickly screw and unscrew hoses, and the whole outer barrel rotates freely. I want to remove it. It leaks like crazy when I turn the valve. I don't know what the hell to call it. Inside the unit is a spring loaded pin that I can pull down, and when I release that it returns up inside the whole thing. There's no obvious way for me to take the whole thing off, unless this is a one-piece thing that includes the valve itself. Here's some photos. Dremel with a cut off wheel. Worst case it looks like you have enough pipe left to be easily able to replace the entire spigot.
|
# ? May 24, 2018 00:23 |
|
devicenull posted:Dremel with a cut off wheel. Worst case it looks like you have enough pipe left to be easily able to replace the entire spigot. That's what I was afraid of. I've got a plumber coming in to install a water softener, maybe I'll have him replace this whole thing at the same time.
|
# ? May 24, 2018 00:33 |
|
VERTiG0 posted:That's what I was afraid of. I've got a plumber coming in to install a water softener, maybe I'll have him replace this whole thing at the same time. I'd at least try to cut off the plastic bit (if you already have the necessary tools). Worst case, you have to get it replaced anyway. Well... worst case as long as you don't somehow cut through the pipe.
|
# ? May 24, 2018 00:39 |
|
Looks like you could just come from the top of the plastic with a screwdriver and hammer and pop it off. That or rip pieces of it off from underneath with a wrench.
|
# ? May 24, 2018 01:52 |
|
Take a hammer in each hand and cymbal the damned thing. No need to pay a plumber.
|
# ? May 24, 2018 02:47 |
|
|
# ? Jun 5, 2024 23:50 |
|
VERTiG0 posted:One out of my outdoor hose spigots has a plastic connector to quickly screw and unscrew hoses, and the whole outer barrel rotates freely. I want to remove it. It leaks like crazy when I turn the valve. I don't know what the hell to call it. Inside the unit is a spring loaded pin that I can pull down, and when I release that it returns up inside the whole thing. There's no obvious way for me to take the whole thing off, unless this is a one-piece thing that includes the valve itself. Here's some photos. I'm pretty sure those are easy to remove. I think its a coiled spring is what holds it onto the threads. You have to grab onto it with a good pair of channel locks and push down while turning.
|
# ? May 24, 2018 02:54 |