|
IOwnCalculus posted:Warren oil is also Supertech / Amazon / Kirkland. They're fine. Both of my Saturns absolutely HATED Supertech. As in clouds of smoke every time I left a stop, a quart to top off every 1-2 weeks (so 8+ qts by the time the oil change reminder popped). Switch back to Mobil 1 and they'd be back to 1 qt to top off between 9-10k oil changes. No idea why. It seems to only be the early Saab-based Ecotecs that hated it.
|
# ? Aug 6, 2020 04:41 |
|
|
# ? Jun 3, 2024 21:38 |
|
STR posted:early Saab-based Ecotecs No wonder those engines are good.
|
# ? Aug 6, 2020 04:51 |
|
About that. There were a handful of parts under the hood of my Saturn with Saab logos. It'd been mutated enough that most Saab parts didn't really work anymore, but it was based on a mid 90s Saab motor. Which, knowing Saab, probably dated back to the 1960s. randomidiot fucked around with this message at 09:05 on Aug 6, 2020 |
# ? Aug 6, 2020 09:02 |
|
STR posted:
On all my years on this planet, I've yet to run across one that actually works. At least they still crank out catalogs.
|
# ? Aug 6, 2020 13:02 |
|
The catalog oil filter for my Pointiac V8 is bigger than the mount for the filter, the thread size and pitch is correct but the filter hangs out over the edge of where it screws in. It is weird but I have tried multiple brands and stores and they all use the same size one.
|
# ? Aug 6, 2020 14:18 |
|
Even AC Delco?
|
# ? Aug 6, 2020 15:00 |
|
Colostomy Bag posted:On all my years on this planet, I've yet to run across one that actually works. At least they still crank out catalogs. Surprisingly, almost all the ones I've run across work.. though the batteries are usually so weak that the LCD barely functions. The Walmart I go to doesn't have paper catalogs anymore. BigPaddy posted:The catalog oil filter for my Pointiac V8 is bigger than the mount for the filter, the thread size and pitch is correct but the filter hangs out over the edge of where it screws in. It is weird but I have tried multiple brands and stores and they all use the same size one. This is only my second time changing the oil on this thing, but the Purolator I had on it before was the correct one. loving tiny little thing though. I'd been wanting to go to the H6 filter just because it's a lot larger. This is roughly in the middle, though seeing it hang over the edge of the oil filter block like that is just a moment. I should have recognized good ol' 3593 - the Fram filter everyone says is right when they don't know which one to throw at it. It's been so long since I was that cheap that I'd forgotten... (Walmart was out of anything cheaper that the computer-thingymabob said would work that day). randomidiot fucked around with this message at 16:09 on Aug 6, 2020 |
# ? Aug 6, 2020 16:03 |
|
Colostomy Bag posted:Even AC Delco? Yep, so either someone put a smaller oil filter adaptor on the thing or it is just 70s GM weirdness.
|
# ? Aug 6, 2020 16:27 |
|
So I looked up the filter application for this filter. It turns out the 3.0 H6 has a wider mating surface on the oil filter block. I wanted to run an H6 filter for the extra filtration media, but never looked up the mount size. And I guess Walmart thinks "welp 3593A fits almost everything, it fits the 2.5 now too!". Turns out good ol' 3593A is indeed the correct filter.. for the 3.0. Sorta. It's Fram's correct version. The real correct version is a bit longer, but just as wide. Same bypass valve pressure. I kind of like the 3.0's filter bypass pressure, it's a lot lower than the 2.5 filter. I'd rather have dirty oil vs a lot less oil flow. As it is now, the oil light flickers off while cranking and it's off by the time the engine kicks (~4 revolutions?), with the old Purolator it would flicker off after a couple of seconds of running. Did that before I changed the oil the first time too, but I'm not sure if dumping Seafoam in the oil cleaned a bunch of poo poo out or not (the oil was loving disgusting, though). I'm not comfortable with a tiny bit of gasket sealing 40+ PSI. I paid for the whole gasket, I want to use the whole gasket. Just like I paid for the whole tach, I want to use the whole tach! I also have a dead PCV valve from what I can tell. Only ONE loving Advance in Austin has the PCV valve in stock. Gonna carefully make my way over there to get both the correct filter and the PCV valve, and keep a close eye on the oil light. randomidiot fucked around with this message at 18:02 on Aug 6, 2020 |
# ? Aug 6, 2020 17:58 |
|
STR posted:
I know I'm preaching to the choir but good luck and be safe. Blew me away how fast a bad oil filter install will piss oil. You only have seconds.
|
# ? Aug 6, 2020 22:28 |
|
If you have a shop vac, use it on the oil fill cap and swap the filter without a drop of oil spilling like a boss. I did this trick for folks once and it's a rare opportunity for cool physics to work and make you look cool/like a huge nerd.
|
# ? Aug 7, 2020 00:46 |
|
Suburban Dad posted:If you have a shop vac, use it on the oil fill cap and swap the filter without a drop of oil spilling like a boss. I did this trick for folks once and it's a rare opportunity for cool physics to work and make you look cool/like a huge nerd.
|
# ? Aug 7, 2020 02:11 |
|
The filter is past the pump, that actually work? I've seen it work for the drain plug but never the filter... I just swap the filter and expect to lose like half a pint plus the filter contents, and top it off after the first start. I actually used a similar trick to get my shitbox 50ish miles home years ago with a hole torn in the bottom of the gas tank. Except the HVAC controls manifold nipple was my shopvac and I pounded the tear mostly closed with a rock before starting. Had to barely touch the throttle to keep the gas in the tank, but it worked.
|
# ? Aug 7, 2020 06:40 |
|
Now that I think about it, I think somebody forgot the drain bolt washer and that's why it was done. Filter or the housing might have a valve that could prevent it from working I guess. Try it, for science!
|
# ? Aug 7, 2020 15:12 |
|
I put a hitch on the van.
|
# ? Aug 9, 2020 03:34 |
|
I made some great progress on a bunch of small projects today. 1997 F150 - Got stuck in 4WD High, could not get it out no matter what. Ended up pulling the actuator on the transfer case and using some YouTube videos to figure out the 4WD vacuum solenoid was still engaged. Pulled the battery and it cleared the memory (I'm guessing in the GEM). The odd thing was moving the switch did nothing. Hope the GEM/switch aren't cooked. But after 365k, what do you do. Also replaced the column shifter which has been long broken and replaced the turnsignal/wiper switch. We've had a long standing problem with the wipers/lights cutting out depending on the column position. Turns out it was a broken tab holding in a pin. Zip tie fixed it, probably for the rest of this trucks life. I've got new brakes/master cylinder/steering stuff for the next time I have free time. 2001 BMW E46 wagon - replaced the broken radiator level sensor I fried when the tank cracked. Still going strong at 265k. Leaks... a lot of oil still. Someday I'll do the FMS. 1987 Motorhome - We've been helping a family during this awesome situation we're all in and the mom was given this R30 Suburban based motorhome. Big old 454. Was gone through 6 years ago with new tires/brakes/suspension. Ordered plugs, wires, fuel filter, and pump. Has 50k on it, but I swear the plugs and wires were last done in 1988. One was burnt clean off at the boot. It's running 10x better now and we can now help them figure out their next steps.
|
# ? Aug 9, 2020 03:40 |
|
the spyder posted:I made some great progress on a bunch of small projects today. Knock on wood, those two tiny vacuum lines and the transfer motor can be a pain in the rear end.
|
# ? Aug 9, 2020 03:49 |
|
the spyder posted:I made some great progress on a bunch of small projects today. Those two loving vacuum solenoids.......I replaced them at least twice a piece in 220k miles on my '97. If it's still on the road I assume they have been replaced again by now. (I bought it new, and it was in the salted north)
|
# ? Aug 9, 2020 04:45 |
|
Suburban Dad posted:If you have a shop vac, use it on the oil fill cap and swap the filter without a drop of oil spilling like a boss. I did this trick for folks once and it's a rare opportunity for cool physics to work and make you look cool/like a huge nerd. I used surgical tubing, a bucket, and an air compressor to siphon transmission fluid. Definitely way less messy than using a shop vac, but not as effective as dropping the pan. You could probably combine the two ideas though; put the shop vac to the lid of the bucket and run the tube from the transmission filler line to the bottom of the bucket, and get better results.
|
# ? Aug 9, 2020 05:27 |
|
GnarlyCharlie4u posted:I used surgical tubing, a bucket, and an air compressor to siphon transmission fluid. Definitely way less messy than using a shop vac, but not as effective as dropping the pan. The point of the shop vac isn't to pull anything out of the engine. You just want to draw a vacuum, so that when you open the drain plug air rushes in and pushes oil out of the way, keeping it from falling on the floor. You swap your drain plug without having to drain the pan, then remove the shop vac, hopefully having not sucked anything actually into the vac.
|
# ? Aug 9, 2020 06:10 |
|
Yeah think of it like putting your finger over the top of a straw when it's in your drink and then lifting it out. Doesn't take much vacuum, just enough to overcome atmospheric pressure pushing down on it.
|
# ? Aug 9, 2020 13:44 |
|
Thank christ I'm not 16 and no longer horney.
|
# ? Aug 9, 2020 20:24 |
|
How many times did you stick your dick in a shop vac?
|
# ? Aug 9, 2020 20:38 |
|
Suburban Dad posted:How many times did you stick your dick in a shop vac? To aid you reaching a number here is a video on counting past infinity https://www.youtube.com/watch?v=SrU9YDoXE88
|
# ? Aug 9, 2020 21:50 |
|
Suburban Dad posted:How many times did you stick your dick in a shop vac? They did deny my warranty claim.
|
# ? Aug 9, 2020 22:40 |
|
Colostomy Bag posted:They did deny my warranty claim. Ew.
|
# ? Aug 11, 2020 20:24 |
|
gently caress serpentine belts. That is all.
|
# ? Aug 13, 2020 02:50 |
|
Suburban Dad posted:How many times did you stick your dick in a shop vac? Oh good I'm not the only one.
|
# ? Aug 13, 2020 03:18 |
|
I spent 3 hours looking for a connector to an unknown computer in the wiring diagram only to find that it's an aftermarket MAF signal translator when I pulled the cover off. I'm dumb.
|
# ? Aug 13, 2020 05:25 |
|
Darchangel posted:Aren't they supposed to make it go slower? Better paint them, ummm... blue? Black? STR posted:About that. There were a handful of parts under the hood of my Saturn with Saab logos.
|
# ? Aug 13, 2020 06:32 |
|
Old title was kinda feeling stale.
|
# ? Aug 15, 2020 10:44 |
|
Lil Richard in a ShopVac sounds like a great band name. On-topic - I'm about to get in my car and go...somewhere. I'm going stir crazy enough that I miss my 30 minute commute each morning/evening. Halp me I'm broken.
|
# ? Aug 15, 2020 13:48 |
|
I was able to get out of the house this afternoon and go for a drive and run an errand, it was great. Then I washed the car after dinner, it was getting pretty filthy.
|
# ? Aug 16, 2020 00:47 |
|
Goober Peas posted:On-topic - I'm about to get in my car and go...somewhere. I'm going stir crazy enough that I miss my 30 minute commute each morning/evening. Halp me I'm broken. In what I did to my ride talk: checked on the locost battery to see if it will live another day. Was discharged down to 3.5v when a storm rolled through and cooked the battery tender. Currently sitting a 9.5v after a week on a new battery tender while hooked up to a second battery. I have a spare battery but it will be a pain in the rear end to replace thanks to how cramped everything is, seeing if I can salvage this one first.
|
# ? Aug 16, 2020 12:31 |
|
Got in the garage during nap time. Did my flares and brake lines on my new rear end. Positioned them to use the existing brake tee and hose. I’ll pull that bracket off and tack it in the right spot after I get everything under the car.
|
# ? Aug 16, 2020 22:03 |
|
Just replaced a pair of front struts, top mount/bearings and the lower engine mount on the rover 75. Of course being britain-land, as i'm laying underneath the car it started pissing down and soaked me, my tools, and my haynes book of lies Pretty sure safety critical components are ok to just torque FT. right?
|
# ? Aug 17, 2020 13:36 |
|
Ah Haynes books. That brings back memories.
|
# ? Aug 17, 2020 14:17 |
|
tbh i'm glad i went for the paper book, if i was trying to use RAVE to get the torque settings, i'da had a dead latitude too...
|
# ? Aug 17, 2020 15:20 |
|
Anghammarad posted:Just replaced a pair of front struts, top mount/bearings and the lower engine mount on the rover 75. Of course being britain-land, as i'm laying underneath the car it started pissing down and soaked me, my tools, and my haynes book of lies The proper torque is “gutentite”. Alternately, tighten until it breaks, then back of 1/4-1/2 turn.
|
# ? Aug 17, 2020 20:01 |
|
|
# ? Jun 3, 2024 21:38 |
|
Darchangel posted:The proper torque is “gutentite”. Alternately, tighten until it breaks, then back of 1/4-1/2 turn. 2-3 ugga duggas
|
# ? Aug 19, 2020 20:04 |