|
https://www.ekwb.com/shop/ek-quantum-vector-fe-rtx-3080-d-rgb-black-special-edition Can't wait to work out the butcher's bill on what this is going to end up costing.
|
# ? Nov 7, 2020 06:40 |
|
|
# ? May 24, 2024 14:53 |
|
a small PSA for those looking into getting the NR200P: the P comes with two top exhaust fans in a nice little setup where you can just press them into some standoffs in the top panel and they'll be all ready to go. unfortunately, they have an issue I've encountered (and confirmed via finding this Reddit post) where they start rattling a bit. I think this is because they just aren't quite properly fitted for the top mesh, and there's some hard plastic that gets rattled. as the post says, you can push down on the top panel a bit to temporarily stop that, but I assume it flexes back into place or something this means I'm probably going to be getting a couple replacement fans, which is a bit of a bummer, since one of the upsides of me getting the P even though I didn't want the TG window was that I got the 2x fans. I'm sure most people getting this are planning to bring their own fans anyways, but just wanted to leave a word of caution on the only problem I've had with this build apparently if you drop the fans to less than ~1000 RPM (they're currently at 1336 RPM) this goes away, and I think i can get away with that since I don't think this system has gone above 70C once. otherwise might grab a pair of Noctua NF-A12x25 PWMs abraham linksys fucked around with this message at 22:38 on Nov 7, 2020 |
# ? Nov 7, 2020 22:28 |
|
Warmachine posted:https://www.ekwb.com/shop/ek-quantum-vector-fe-rtx-3080-d-rgb-black-special-edition Man, that is pretty as gently caress, but ouch at being $100 over EK's already pricey other GPU blocks. I mean, I'd get one if I had a FE, but I ended up with a Zotac so I'll have to get something else (or wait for the Gigabyte/ASUS watercooled ones to come out and trade up).
|
# ? Nov 8, 2020 03:06 |
|
I don't follow the GPU game a ton. How long will Nvidia keep cranking out the FE cards?
|
# ? Nov 8, 2020 04:56 |
|
Hahahaha it posts! My unobtanium pc is alive! Now for the hellish task of cable management in this case. SF750, 5800x, 3080, nr200... I cannot believe I finally collected it all!
|
# ? Nov 8, 2020 05:00 |
|
VorpalFish posted:Hahahaha it posts! My unobtanium pc is alive! Now for the hellish task of cable management in this case. Replace the 5800x with a 5900x and you got what I have been thinking about building.
|
# ? Nov 8, 2020 05:32 |
|
Moey posted:I don't follow the GPU game a ton. How long will Nvidia keep cranking out the FE cards? For the lifecycle of the card, if history is any indication.
|
# ? Nov 8, 2020 06:23 |
|
VorpalFish posted:Hahahaha it posts! My unobtanium pc is alive! Now for the hellish task of cable management in this case. Same here just with the M1 instead of nr200, last piece is the 5800X and it arrives Monday.
|
# ? Nov 8, 2020 08:13 |
|
MaxxBot posted:Same here just with the M1 instead of nr200, last piece is the 5800X and it arrives Monday. Why did I do this? I've given up on even the pretense of cable management. Whatever, it's alive. Edit: on the other hand, now that I've dialed in an undervolt, I can just barely hear the fans during timespy with the GPU at 65C so if I loosen up the curve a bit and let it float to 70ish, I think I may have my inaudible PC. Edit2: Wow, A12x25s are completely insane, I actually cannot hear these running at 60% from like 2 feet away in a completely mesh case. VorpalFish fucked around with this message at 02:47 on Nov 9, 2020 |
# ? Nov 9, 2020 02:26 |
|
Warmachine posted:For the lifecycle of the card, if history is any indication. Do 3rd party cards ever drop cheaper than FE? Or are you just shopping for boost clocks/leds? In theory, the 3080 FE may be in stock somewhere in a few months?
|
# ? Nov 9, 2020 04:00 |
|
I am now realizing that the fans I've been using to draw more air into the GPU chamber of my Node 202 are pressure-optimized for radiators and heatsinks, both the Fractal Design Venturi HP-12s and the Noctua NF-P12s I replaced them with I'm wondering if I should try replacing them with an airflow-optimized model, like the thread-favorite Noctua NF-A12x25 or the even-quieter and airflowier NF-S12A
|
# ? Nov 9, 2020 06:08 |
|
HappyCapybaraFamily posted:I am now realizing that the fans I've been using to draw more air into the GPU chamber of my Node 202 are pressure-optimized for radiators and heatsinks, both the Fractal Design Venturi HP-12s and the Noctua NF-P12s I replaced them with I think you want the pressure optimized fans because they work great in space constricted places (drawing through a dust filter straight into a solid GPU). The airflow optimized fans are good for unrestricted airflow (like in a Meshify C or something) Not 100% sure though since I struggle to remember what's what as well.
|
# ? Nov 9, 2020 08:04 |
|
Yea you’re not exactly going to be moving a ton of air through a 202. The fans you have are more than capable.
|
# ? Nov 9, 2020 08:47 |
|
That said, A12x25s are loving magical, just unreasonably expensive. Arctic P12s are nearly as good for a third of the cost, but a lot of people have noticed motor hum between 1000-1200 rpm so maybe only worth it if you can keep them below 1k.
|
# ? Nov 9, 2020 13:37 |
|
HappyCapybaraFamily posted:I am now realizing that the fans I've been using to draw more air into the GPU chamber of my Node 202 are pressure-optimized for radiators and heatsinks, both the Fractal Design Venturi HP-12s and the Noctua NF-P12s I replaced them with a12x25 are both pressure and airflow optimised, that's kind of their deal. For the enthusiast that wants it all (and doesn't mind the cost and colour) HappyCapybaraFamily posted:The CPU cooler and fan are the ID-COOLING IS-60 with its stock fan replaced with a Noctua NF-A12x15, which was recommended to me by others in this very thread. Even quieter than the case fans somehow even under load, and the cooler height is just perfect to reach fresh air outside the case even with the filter installed. I'm glad the is-60 + a12x15 worked out as well for you as it did me, it's basically peak hsf when it comes to an unmodified node 202 HalloKitty fucked around with this message at 15:31 on Nov 9, 2020 |
# ? Nov 9, 2020 15:24 |
|
I moved my old desktop z97 system into the Sugo 14 case. I have to say I really like the case and the flexibility it gives me for how I want to cool things and where I can mount drives etc. In my old Sugo 05 I have an SSD just hanging out in the front of the case held in place by cable tension. In the 14 there's a drive mount in the case and two up front that I saw. I fit a 240mm radiator with no problem. I will say using an sfx power supply with atx bracket gave me more room for cable clutter but a full size atx power supply wouldn't have been a problem. I'm thinking of getting me a cheap ryzen 7 system to put in there depending on sales over black friday. Fits nicely if a little snuggly in my media center beneath the tv.
|
# ? Nov 9, 2020 15:56 |
|
Moey posted:Do 3rd party cards ever drop cheaper than FE? Or are you just shopping for boost clocks/leds? Nope, the FE makes an effective price floor: everything else will be more expensive unless you find one of the cheaper cards with a $50 sale or something. NVidia has yet to discontinue a FE card to my knowledge, so there's no reason to expect that you wouldn't still be able to get one in a few months (I mean, as much as you'll be able to get any 3080, anyhow). Despite the name, they're not being positioned as limited editions or something like that. VorpalFish posted:That said, A12x25s are loving magical, just unreasonably expensive. Arctic P12s are nearly as good for a third of the cost, but a lot of people have noticed motor hum between 1000-1200 rpm so maybe only worth it if you can keep them below 1k. Or just use the fan control software either built into basically every motherboard these days or via Windows to set a fan curve that skips that particular RPM segment, and just jumps from like 900RPM to 1100RPM. Not every P12 exhibits the issue, either. But it's like 10 min of work to save $20/fan.
|
# ? Nov 9, 2020 17:52 |
|
DrDork posted:Nope, the FE makes an effective price floor: everything else will be more expensive unless you find one of the cheaper cards with a $50 sale or something. NVidia has yet to discontinue a FE card to my knowledge, so there's no reason to expect that you wouldn't still be able to get one in a few months (I mean, as much as you'll be able to get any 3080, anyhow). Despite the name, they're not being positioned as limited editions or something like that. Doesn't it do it on the way as it accelerates? That would drive me nuts even if it was half a second.
|
# ? Nov 9, 2020 20:46 |
|
VorpalFish posted:Doesn't it do it on the way as it accelerates? That would drive me nuts even if it was half a second. Yeah, the fan itself will indeed have to pass through that speed zone at least momentarily. I have a bunch of the P12's, though, and I can say that the resonance "noise" is not bad at all. It's a difference between being effectively silent to "I think maybe I can hear something?" So if it's just there for 1 second as a transient state you're not likely to notice it. But of course YMMV, and if money and brown coloring isn't a concern you can get the Nocturas and avoid the issue entirely.
|
# ? Nov 9, 2020 20:58 |
|
DrDork posted:if ... brown coloring isn't a concern
|
# ? Nov 9, 2020 22:29 |
|
There should be black and white fans in Q1 2021 sometime..? Incidentally, what was the optimal fan configuration on the NR200P again?
|
# ? Nov 9, 2020 23:11 |
|
Rhaka posted:There should be black and white fans in Q1 2021 sometime..? Sycthe Fuma 2, Noctua C14S are both good, NH-U12A if you're not using the tempered glass is an option but I heard the Fuma 2 beats it, and just almost barely fits with the tempered glass. e: whoops, misread. I think bottom intake with rear exhaust works good, with potential top intake fans if your motherboard allows space.
|
# ? Nov 10, 2020 00:10 |
|
HalloKitty posted:a12x25 are both pressure and airflow optimised, that's kind of their deal. For the enthusiast that wants it all (and doesn't mind the cost and colour) Yeah, that heatsink-fan combo really is the best for my use case. Ran some real-world RDR2 yesterday, and the CPU stayed below 75° the whole time the thread posted:fan talk Ah, good to know that the high pressure is useful pulling air through a filter, which is what I'm doing. Still tempted to try the magical NF-A12X25 to get even quieter, though, especially given Noctua's handy comparison chart up there (the redux fans I have are essentially equivalent to the NF-F12s, I think)
|
# ? Nov 10, 2020 00:28 |
|
Turns out my 3900X is dead, but the Fuma 2 installation was alright. Fan clips are annoying / worse than Noctuas IMO, but definitely fits snugly. I'm not sure what other fans to add to this case — GPU has its own standard blower thing and the Fuma is front intake, rear exhaust...top intakes, I guess? Not much else to cool really, M.2 is under a heatsink.
|
# ? Nov 10, 2020 01:03 |
|
CopperHound posted:I like the brown. I just wish there was a case the complimented the color palette. Wander into any used computer parts store. You'll have your pick of the litter
|
# ? Nov 10, 2020 01:08 |
|
Would be cool if Noctua designed a silence/performance oriented case that matched their aesthetic.
|
# ? Nov 10, 2020 09:33 |
|
Wahaha360 just showed a glimpse of the "budget" version of the FormD P1, the Mesh-Licious (working name lol).
|
# ? Nov 10, 2020 13:53 |
|
DrDork posted:Nope, the FE makes an effective price floor: everything else will be more expensive unless you find one of the cheaper cards with a $50 sale or something. NVidia has yet to discontinue a FE card to my knowledge, so there's no reason to expect that you wouldn't still be able to get one in a few months (I mean, as much as you'll be able to get any 3080, anyhow). Despite the name, they're not being positioned as limited editions or something like that. Thanks. I guess I'll keep my eyes peeled over the next few months.
|
# ? Nov 10, 2020 15:25 |
|
ijyt posted:Wahaha360 just showed a glimpse of the "budget" version of the FormD P1, the Mesh-Licious (working name lol). Nice, I am curious to see how that turns out when it's finalized.
|
# ? Nov 10, 2020 16:19 |
|
Hi thread, here's another nr200p owner wanting a sanity check. I've got my nr200p and FE 3080 and am just waiting on a 5600x to pull the trigger on the rest of my build. I don't mind tinkering but when it's all put together I don't particularly want to gently caress about with trying a million different cooling configurations or messing around with fan curves to find the peak optimal whatever. I'd just be happy with a good level of sound/thermal performance. With that in mind, I was thinking about getting the NH-u12A because it just barely allows the full size top rear fan, leaving the two stock fans as exhaust out the top and having the u12A exhausting out the back. Then I would see how acceptable the performance was and if I wasn't happy I could think about getting a couple of Noctua A12x25 for the bottom as intakes. Obviously in this configuration I'd have to use the mesh side panel which is fine. However I'm now considering the Fuma Scythe 2 because it's as good if not better performance-wise while being 40% cheaper. It's also a little shorter which allows for the tempered glass side panel, should I want to use that for a change. This means I'd have to lose the top rear full-size fan, which led me down a rabbit hole of considerations. Could I swap the 15mm fan from the Scythe with the stock 25mm rear top fan? Would that be inadvisable because of the noise from the stock fan being used on the CPU cooler? Should I just set aside the stock case fans regardless and go for Noctuas for their quietness? Should I stick with the Fuma 2 in stock configuration, buy a slim 15mm case fan for the top exhaust, then use the stock 25mm fan I took from the top and use that as a bottom intake? I've watched lots of videos and I don't feel any clearer although I know I'm fretting over minor differences, as long as I have a decent CPU cooler I know the nr200 does well enough with the FE 30x0 cards. Someone please sort me out.
|
# ? Nov 10, 2020 16:20 |
|
ijyt posted:Wahaha360 just showed a glimpse of the "budget" version of the FormD P1, the Mesh-Licious (working name lol). How do you get video cables to the GPU when it's oriented like that?
|
# ? Nov 10, 2020 16:45 |
|
Butterfly Valley posted:Hi thread, here's another nr200p owner wanting a sanity check. A few things; -depending on your board, you may be able to fit a 25mm thick fan over the fuma 2. I couldn't, but I have a gigabyte board with high socket placement -the default mounting system for the nr200 won't let you mount 15mm thick fans properly. If you want to thin fans, 4x25mm clevis pins work well -with the aforementioned clevis pins I was able to mount an a12x15, but the fan grill made contact with the fan hub and stopped it from spinning. I jury rigged it using the hard drive mounting grommets that came with the case as spacers but if I knew before hand, actual washers would probably have been better. This may not be an issue with all fans, the a12x15 just has corners that are level with the hub. -the included fans for the fuma2 are quiet, the only reason I didn't use the slim one for the top is the rpm caps at 1200 and I wanted a fan that matched the a12x25 more closely since I'm running both top fans from a pwm splitter. I posted a picture upthread if you want to see, but I mounted the fuma2 backwards and set it up as intake because I removed the fans from my gpu and I'm running top and bottom exhaust.
|
# ? Nov 10, 2020 17:38 |
|
Thanks for the heads up. I found a file for 3D printed pins someone specifically designed for the slim noctua 12x15 fans in the nr200 so I might see if I can get someone I know with a 3D printer to help me out, because I'm also looking at the Gigabyte Aorus board. I think I'll go with the Fuma 2 exhausting out the back, buy an a12x15 and a12x25 for the top as exhaust and move the two stock case fans to bottom intake. If they're too noisy I can always leave them out or swap them for a12x25s later.
|
# ? Nov 10, 2020 18:07 |
|
Butterfly Valley posted:Thanks for the heads up. I found a file for 3D printed pins someone specifically designed for the slim noctua 12x15 fans in the nr200 so I might see if I can get someone I know with a 3D printer to help me out, because I'm also looking at the Gigabyte Aorus board. Only other thing is depending on how thick your gpur gpu is you may need slim fans for the bottom too.
|
# ? Nov 10, 2020 18:21 |
|
It's the FE 3080 so I'm good there.
|
# ? Nov 10, 2020 18:25 |
|
Actually, what IS the clearance on the bottom of the NR200 with a 2 slot card? Wondering how thick a radiator would fit for a custom loop with 25mm fans.
|
# ? Nov 10, 2020 18:32 |
|
ijyt posted:Actually, what IS the clearance on the bottom of the NR200 with a 2 slot card? Wondering how thick a radiator would fit for a custom loop with 25mm fans. Just eyeballing it I doubt there's clearance for a 2 slot card, 25mm fans, and a 27mm radiator, but if you're putting a block on the card, couldn't you get it down to single slot? Edit: looks like dual rad is rough and probably involves 15mm fans max in the bottom based on this dude's build: https://www.reddit.com/r/sffpc/comments/ij4nou/nr200_triple_rad_with_280_side_current_build/ VorpalFish fucked around with this message at 21:57 on Nov 10, 2020 |
# ? Nov 10, 2020 21:36 |
|
SalTheBard posted:How do you get video cables to the GPU when it's oriented like that? Presumably using an angled video cable like this. Hard to tell with just that picture though.
|
# ? Nov 11, 2020 00:05 |
|
OK, dream scenario for me here is to find a sub 15L case which will house a 3080 and Ryzen 5900x for my editing rig I'm planning on building next year. Which case would you guys pick if money were no object? (Money is, in fact, a BIG object but just go along with me here)
|
# ? Nov 11, 2020 15:34 |
|
|
# ? May 24, 2024 14:53 |
|
I would probably go for watercooling the 5900x in a Sliger SM580 (because after my SM560 I'm a Sliger fanboy)
|
# ? Nov 11, 2020 15:36 |