|
epswing posted:Why do HD factory service manuals list torque specs in ranges? Sometimes the range is substantial, e.g. "70-80 lb-ft". Why force the technician holding the torque wrench to make a decision on what they'll dial in? Because precise torque actually doesn't matter, as long as it's tight enough, but not too tight. As long as it's in that range, it won't fall off and you won't break anything.
|
# ? Jan 6, 2023 19:09 |
|
|
# ? Jun 5, 2024 05:32 |
That's normal, it's just a different way of expressing value +-percentage. Judgement and experience are what helps you work out the compromise between the factory number and the real world situation in front of you which is what the range is for eg the thread is a bit lovely so you have to torque more towards the higher end to fight through the resistance. Just aim for the middle.
|
|
# ? Jan 6, 2023 19:11 |
|
epswing posted:Why do HD factory service manuals list torque specs in ranges? Sometimes the range is substantial, e.g. "70-80 lb-ft". Why force the technician holding the torque wrench to make a decision on what they'll dial in? Torque values aren't generally an exact figure like, say, valve clearances are. The goal in setting the torque is to make it tight enough that it will hold the parts together properly and not loosen up, but not so tight that the fixture is damaged or it becomes insanely difficult to remove. In your example, 70 is what they consider enough to hold it together (with some margin built in, if the engineers did their job), and while it's unlikely anything would be damaged by overshooting 80 a little, there's no need to go past that. So anything in that range will be fine. Your wheel isn't going to fall off if you put 72 lb-ft on the nuts instead of 75 lb-ft. As Slavvy says, just pick the middle value.
|
# ? Jan 6, 2023 19:17 |
|
LimaBiker posted:My experience with Proxxon is limited to a modern electric jig saw (very quiet and precise) and an old Micromot 'dremel', the one with the external transformer. So I ordered a proxxon the other night. Picked the "professional" model because more power and larger number of positive reviews on amazon, etc. Didn't pay attention to the delivery date. The accessory pack of dremel polishing/grinding tools was delivered 1-2 days later, but the Proxxon won't be delivered until Feb 2, according to the current order status. Not sure if that is magically going to be delivered much faster, or if I should cancel the order and get something else so I can finish up this stupid project.
|
# ? Jan 9, 2023 00:53 |
|
Do y’all fill up on the way home or on the way out? Or no particular way.
|
# ? Jan 10, 2023 02:12 |
|
Russian Bear posted:Do y’all fill up on the way home or on the way out? Or no particular way. When I need gas
|
# ? Jan 10, 2023 02:16 |
|
Around town I'm usually using as much of the tank up as I can, which basically means I'm always filling up on the way out of town lol.
|
# ? Jan 10, 2023 04:08 |
|
I keep a five gallon can at home for refills. Every now and then I'll get it on my way to work at the local station.
|
# ? Jan 10, 2023 04:10 |
|
For me, it depends on the bike really. If it's not my daily I fill it up close to home before I park it so its stored with a full tank so the first thing I have to do when leaving the next weekend is not to fill it up.
|
# ? Jan 10, 2023 08:15 |
|
Same. On the gas topic, is there any problem with storing an emptied gas can for long periods, in terms of things like the stale remnants getting into the next batch you put in it? I've got a 1gallon tank that rarely gets used for long VanVan excursions, and I prefer to keep it empty because its other purpose is having something to drain the tank into if I need to.
|
# ? Jan 10, 2023 16:43 |
|
No offense but that has got to be the weirdest question I have heard in a long time. No, there is no reason to be concerned about the quality of the gasoline in an empty gas can. It's...empty. Even if there are a few milliliters of "remnants" in the bottom of the can, it will make zero difference to anything because those remnants will be diluted 1000-fold when you fill the can up with new gas. Even if the old gas turned into pure nitroglycerine it would probably cause no problems in your engine because the volume is so microscopic. I think the problems of old gas are vastly overstated on the internet. I've run years-old gas from old cans sitting in the shed just to use it up, dumping it into half a tank of fresh gas from the station, and had no problems. Did it burn as well as new gas? Probably not, but I couldn't tell any difference. If you're really concerned about the quality of an old can you've got sitting around, just dilute it 50:50 with new stuff and dump it in. I guarantee it will be completely fine. Sagebrush fucked around with this message at 17:32 on Jan 10, 2023 |
# ? Jan 10, 2023 17:30 |
|
It used to be a much bigger issue than it is now, from my understanding. But just like the “all Harleys leak oil” poo poo that’s been outdated since at least the 90’s, we’re stuck hearing about problems boomers had when they were 25 until the heat death of the universe.
|
# ? Jan 10, 2023 19:09 |
|
OK that's good to hear. I've absolutely been overthinking the potential for bad gas, having seen many random internet posters calling out California gas as particularly prone to bad batches, and being shocked by how short the supposed shelf life is (< 1 year) versus growing up with cans just hanging out in the garage for years and nobody giving it a thought when we'd dump it into the mower.
|
# ? Jan 11, 2023 02:50 |
The worst case scenario for bad gas (excluding stuff that's evaporated in the bowl which is a different situation) is a high performance bike with carbs. The more volatile parts of the gas leave first, yeah this theoretically reduces performance but more importantly it hampers it from atomizing with the air. When you have a peaky engine, with large carbs, there is a fairly sluggish low rpm pull through the carb at the best of times and combined with stale gas this can lead to poor starting and running. I imagine California in particular has high ethanol percentages in their petrol, ethanol attracts water and past a certain water content you'll have real difficulty getting a carburetor to work properly. If you have efi the problem is far reduced because the petrol gets atomized by force when it's sprayed through the injector. If you have a tractor bike with a carb the problem is reduced because there is a healthy pull through the carb even at idle and probably less compression ratio to deal with from a performance standpoint. A lawnmower is on the extreme end of this half of the spectrum and will therefore run on anything vaguely flammable.
|
|
# ? Jan 11, 2023 03:35 |
|
Going to bleed the brakes on my 400 and finally change out the brake lines, would something like this be a good bleeder kit or does it look like rear end?: https://www.harborfreight.com/brake-fluid-bleeder-92924.html They have a more expensive version here that may be less cheaply made: https://www.harborfreight.com/pneumatic-air-operated-brake-bleeder-with-auto-refill-kit-57057.html Now that I have an air compressor I want to get something that will make it easy and idiot proof as possible for my dumb rear end, this will be the first time I've ever done a brake bleed or changed out brake lines.
|
# ? Jan 14, 2023 23:03 |
|
Kind of overly complicated and fussy and not necessary for a bike. Just get a set of speed bleeders.
|
# ? Jan 14, 2023 23:06 |
|
Ah something like these here and then a bag/container and hose of some type to hook to? Chart says front and rear calipers are same size so guessing I can get one and do them individually? https://www.revzilla.com/motorcycle/speed-bleeder-for-metric-bikes?sku_id=1215303
|
# ? Jan 15, 2023 00:03 |
|
No, you need one for each caliper because you install them permanently. If you took them out after bleeding the brakes, a bunch of air would get in and set you back to square one.
|
# ? Jan 15, 2023 00:07 |
|
RightClickSaveAs posted:Ah something like these here and then a bag/container and hose of some type to hook to? Chart says front and rear calipers are same size so guessing I can get one and do them individually? Yup. I just stick a clear hose into a jar or whatever's handy. And like was mentioned, you leave them installed, they replace your standard bleeders.
|
# ? Jan 15, 2023 01:05 |
|
Ohh those replace caliper parts, got it now... that looks really handy. Thanks all!
|
# ? Jan 15, 2023 04:37 |
|
Ended up grabbing this at a local Cycle Gear since I wanted to get started today and hopefully have the whole project wrapped up in the next week. https://www.cyclegear.com/accessories/stockton-brake-bleeder-tool?sku_id=1124076 Bit overpriced for what it is, but the one way valve is a nice feature for bleeding and replacing. Since I was just draining the system completely and the lines are getting removed I probably could have just skipped it, but good first run to see how it all works and will be very handy for the new lines. The hose it comes with is ridiculously stiff and a pain to get the little clamps in place, but once I did, it seemed airtight, and the hose was stiff enough to hold the bottle in place by itself. Wish there was a better way to empty the intake section of hose, as the pressure once the lines are dry aren't enough to push it out, but it's not much so easy enough to disconnect and catch in a reservoir. Got the front brake reservoir drained before it got dark, plan to start working on the front brake line replacement tomorrow.
|
# ? Jan 16, 2023 03:51 |
|
The front brake on the tiger has become sticky as hell. Like, I'll start to pull on the lever and then it *sticks* pull a little harder and then it *sticks* again, finally pull a little bit harder than that and then its full on stoppie power and I end up 20 feet short of the light. What the crap could be causing this? edit: going to bleed the front since its been a few years since I flushed the fluid. what else can I look for?
|
# ? Jan 19, 2023 05:33 |
|
Had the exact same issue on my first bike, it was the fluid.
|
# ? Jan 19, 2023 05:58 |
Arson Daily posted:The front brake on the tiger has become sticky as hell. Like, I'll start to pull on the lever and then it *sticks* pull a little harder and then it *sticks* again, finally pull a little bit harder than that and then its full on stoppie power and I end up 20 feet short of the light. What the crap could be causing this? Grease your lever
|
|
# ? Jan 19, 2023 06:08 |
|
Yeah that sure sounds like a sticky lever to me. Take it off and clean it with kerosene or WD-40 and grease the moving surfaces.
|
# ? Jan 19, 2023 07:53 |
|
Might also be the cable that needs some lube.
|
# ? Jan 19, 2023 17:49 |
builds character posted:Might also be the cable that needs some lube. ??? I mean I know it's a triumph but they aren't THAT lovely
|
|
# ? Jan 19, 2023 17:52 |
|
Slavvy posted:??? You mean this premium European bike.
|
# ? Jan 19, 2023 18:56 |
|
Slavvy posted:??? Spoken like someone who's never ridden through salt! It does seem unlikely, I admit.
|
# ? Jan 19, 2023 18:59 |
Russian Bear posted:You mean this premium European bike. I like how you can just stick a badge on something and it magically makes people think it's fancy. builds character posted:Spoken like someone who's never ridden through salt! Unlikely for a tiger to have a cable operated brake yeah
|
|
# ? Jan 19, 2023 20:19 |
|
Slavvy posted:Grease your lever Kinky
|
# ? Jan 19, 2023 20:34 |
|
Arson Daily posted:Hincky
|
# ? Jan 19, 2023 21:40 |
|
|
# ? Jan 19, 2023 22:35 |
|
Slavvy posted:I like how you can just stick a badge on something and it magically makes people think it's fancy. oh right, I'm just being a big idiot.
|
# ? Jan 20, 2023 00:52 |
|
my immediate thought also was "lube the cable" but one of my bike does, in fact, have a cable-operated front brake. like a bicycle
|
# ? Jan 20, 2023 07:45 |
|
I've encountered sticky hydraulic brake levers too recently, both on my brother's SV when I had it on loan and on bicycles. I've never done anything as ambitous about it as disassembly+clean+grease though, just half-assedly applied some light oil to see if it would help, which it did (no doubt only short term, I should do something about that)
|
# ? Jan 20, 2023 08:02 |
Sagebrush posted:my immediate thought also was "lube the cable" but one of my bike does, in fact, have a cable-operated front brake. like a bicycle Is it a drum, or the psychotic Honda cable operated disc that is somehow worse than a drum?
|
|
# ? Jan 20, 2023 08:12 |
|
I used to have a 2014 Giant Road bike that had cable operated disc brakes. They worked great for the 21k miles I put on the bike, but I'm not sure I'd want it on something motorized
|
# ? Jan 20, 2023 14:23 |
|
my wifes bike (bicycle) has cable operated disk brakes, and all I know about them is they are loud as hell. Having ridden a bicycle with actual hydraulic brakes, they are no comparison
|
# ? Jan 20, 2023 23:30 |
|
|
# ? Jun 5, 2024 05:32 |
|
Give us cable actuated rim brakes.
|
# ? Jan 20, 2023 23:38 |