|
The more brands of parts you have in it, the more AMC it is.
|
# ? Sep 25, 2023 03:47 |
|
|
# ? May 9, 2024 23:46 |
|
I have been able to get some more work done the last few weeks, things are still moving slow but I'm making progress. I had to make a L bracket to relocate the pivot on the Z-bar for the clutch linkage. Since I'm using a late model AMC/Jeep bellhousing the pivot mounting location was wrong. (It would normally bolt directly to the bellhousing)The other end of the Z-bar mounts in the strut rod bracket so that end couldn't be relocated. I set the clutch pushrod adjustment and verified that the clutch would release and had proper free play. Transmission installed with a shortened driveshaft and a slip yoke swap to match the T-5. Had to extend the mounting surface of the cross member with some 1/4 inch plate. The transmission mount is for a 69 Mercury Cougar but it fits the transmission perfectly and has the correct height I needed for the driveshaft angle. I'm fairly sure the modification work is about done, I won't weld in the transmission mount plate extension until I have been able to test drive the car and make sure the positioning is OK. I hope to have it running and be able to move under its own power by the end of November.
|
# ? Oct 29, 2023 04:03 |
|
hell yeah more amc content. how much work was the T5 swap? i didn't know you could use the ford transmission. on the T10, the bolt pattern is different.
|
# ? Oct 29, 2023 09:14 |
|
Swiller of Beer posted:Not much of an update, was finally able to get some free time to put some work in. I forgot to take pictures so there is only a couple of them.
|
# ? Oct 29, 2023 19:21 |
|
Raluek posted:hell yeah more amc content. how much work was the T5 swap? i didn't know you could use the ford transmission. on the T10, the bolt pattern is different. It wasn't too bad, I used an AMC/Jeep multi fit bell housing (AMC part number 3229127), and a clutch kit and release fork from a 77 CJ7 to make it work. You need a Ford t5 with a 7.18 inch long input shaft. You also need the Jeep t5 input shaft bearing retainer (Jeep part number 8134013) to fit the hole in the bellhousing. And I also used a slip yoke for a Mustang (Spicer part number 2-3-8251x) and had the driveshaft shop install it on the driveshaft when I had it shortened. And like I said before I had to work up a transmission mount and deal with the Z-bar.
|
# ? Oct 29, 2023 20:36 |
|
Still here, still working on this when I have free time. Cleaned up the distributor, replaced the points and condenser. Verified the mechanical and vacuum advance are free and working. I will probably convert the distributor over to electronic ignition sometime in the future but I actually like points. My first car had points, it's a nostalgia thing I guess. I'll just have to keep a spare set and condenser in the glovebox like the old days. Replaced the exhaust flange studs on the exhaust manifolds before installing them. Deleted the frozen heat riser. I didn't get any pictures of installing the manifolds but the drivers side sucks to do in the car, there's no way to get to the bolts without removing the steering column. Next time they go in with the engine. The biggest issue at the moment is finding a fuel pump that is not poo poo. I installed a brand new Carter only to have it start leaking fuel from the weep hole immediately. After doing some research it seems all the AMC mechanical pumps are garbage nowadays so I might have to go electric. Ugh.
|
# ? Jan 3, 2024 02:49 |
|
If you want electronic ignition, Ford Duraspark II is easy to install and dead simple.
|
# ? Jan 3, 2024 04:18 |
|
Salami Surgeon posted:If you want electronic ignition, Ford Duraspark II is easy to install and dead simple. I actually have an AMC duraspark distributor, harness and module on the shelf. I could also swap to a big cap HEI distributor but those are ugly. I like the look of the old Delco distributor plus the sliding window in the cap makes setting points easy with a dwell meter. In the end I will probably convert the Delco distributor to electronic ignition eventually.
|
# ? Jan 3, 2024 04:45 |
|
Swiller of Beer posted:The biggest issue at the moment is finding a fuel pump that is not poo poo. I installed a brand new Carter only to have it start leaking fuel from the weep hole immediately. After doing some research it seems all the AMC mechanical pumps are garbage nowadays so I might have to go electric. Ugh. yeah from what ive read, this is the unfortunate truth. you either find an old original one that's supposedly rebuildable, or convert to electric, or spend multiple hundreds on a fancy aftermarket one (robbmc). the new production stock replacement ones ive heard nothing but problems.
|
# ? Jan 3, 2024 05:30 |
|
Raluek posted:yeah from what ive read, this is the unfortunate truth. you either find an old original one that's supposedly rebuildable, or convert to electric, or spend multiple hundreds on a fancy aftermarket one (robbmc). the new production stock replacement ones ive heard nothing but problems. I'm probably going to go electric if this next pump fails, the robbmc pump is pricey and a bit overkill for a 304. I have a GMB pump ordered which is supposedly made in South Korea and some people say it may have better build quality. It's worth a shot anyways. If it works out I'll order a spare to keep in the trunk just in case.
|
# ? Jan 4, 2024 01:39 |
|
Slowly we continue on. Got the accessories figured out, I updated the alternator and power steering to the late model setup so I could use a Delco alternator instead of the externally regulated Motorola. Plus the new alternator is a 61 amp unit vs the old 40 amp unit. It also simplifies the wiring quite a bit and parts are much easier to come by if I need to replace anything. I will say AMC has one of the dumbest and complicated accessory bracket designs I have ever seen for a vintage car.
|
# ? Feb 6, 2024 14:53 |
|
https://www.youtube.com/watch?v=__2E4pQ1V-k Finally up and running. Took it for a short drive and didn't have any issues as of yet. Going to start on fabricating the exhaust next week if I have time.
|
# ? Mar 27, 2024 12:59 |
|
I completed the exhaust over the weekend, I don't have any pics or videos because I'm lousy about remembering to take them. I used one of those cheap mandrel bent cut it yourself kits from eBay for the pipes and a pair of turbo mufflers with turndowns. Fairly simple to build and a lot cheaper than the exhaust shops around here wanted for the job. Since the car was up on jack stands I'm going to go ahead and start on replacing the rear leaf springs. The left rear has lost it's arch and I have a new set that I bought a while ago gathering dust so I'm just going to get it over with. I'll replace the rear shocks and the parking brake cables while I'm there so I can stop using a concrete block as my parking brake. That'll be nice. The only things left to do under the car once the springs and cables are done is replace the fuel sender in the tank, finish the install of the inline electric fuel pump (after 3 straight junk new mechanical fuel pumps I give up) and service the rear axle. At that point the car will be as reliable as I can make it and hopefully I can make it farther than the seven miles I made it the first time I drove it two years ago.
|
# ? May 7, 2024 01:33 |
|
|
# ? May 9, 2024 23:46 |
|
That shifter is great. Oh, and the pro move is a harbor freight rubber chock block with about 6 feet of rope tied to it. That way you can string the rope in through your window, drive off the block a little and anchors aweigh, capn!
|
# ? May 7, 2024 07:11 |