|
Slavvy posted:In theory, the absolutely proper way would be to power those things using a relay(s) switched on and off by the ignition. Thank you Slavvy. Regarding longer terminal battery bolts, are these long enough?: https://www.amazon.co.uk/gp/product/B01D3JJS1Q/ref=ox_sc_mini_detail?ie=UTF8&psc=1&smid=AG3014UY92J9X Steakandchips fucked around with this message at 19:35 on Nov 7, 2019 |
# ? Nov 7, 2019 19:22 |
|
|
# ? May 16, 2024 05:56 |
|
Renaissance Robot posted:I will say however that the CBF125 has a pretty weak alternator that can't even keep the headlight fully lit at idle, so you might want to check the specs to be sure it's actually capable of supplying enough power to run those things and charge the battery at the same time, otherwise yeah, you'll end up with a flat battery. Thanks for this. This is what the manual says: So does the alternator in this case provide enough for a GPS and 12V heated gloves? If no, should I get a battery like this?: https://www.sportsbikeshop.co.uk/motorcycle_parts/content_prod/248929
|
# ? Nov 7, 2019 19:28 |
|
How much wiggle room is there in torque specs usually? My owner's manual says 20Nm for the oil drain plug, but the service manual says 29Nm. Steakandchips posted:Thanks for this. Gloves tend to run something like 25W iirc (they'll definitely state the power draw in the manual), GPS I don't know but I imagine not more than like 15W? Anyway, add those numbers to the given draw of things you'll have on continuously, and it doesn't look like you should be going above 100W. So it should be fine so long as you're keeping your revs up and not lugging it everywhere. Let us know how you get on! Mods are good. Renaissance Robot fucked around with this message at 19:38 on Nov 7, 2019 |
# ? Nov 7, 2019 19:31 |
|
Renaissance Robot posted:How much wiggle room is there in torque specs usually? I could see that being a typo, like the person writing it fatfingered either the 9 or the 0, rather than a legitimate spread in torque values. 50% of the lower value is enormous. Honestly I don't think I've ever torqued an oil pan bolt. It helps having Weak Little Noodly Arms, makes it tougher to strip them. I always just tighten it till it doesn't really want to move any more, then run the engine for a minute to make sure oil's not dripping out the bottom.
|
# ? Nov 7, 2019 19:48 |
|
I use a torque wrench on it because it's important it's tight enough not to leak, but also a huge pain in the rear end if I strip it. You could split the baby and make it 24.5Nm (my bike is 25Nm).
|
# ? Nov 7, 2019 19:53 |
|
Too late I already did 29! Since I've mostly been working out of the service manual this is probably what I set it to last time as well, so it might be fine. Would be nice if I could actually remember though. e/ if it's a typo then either a) it's weirdly consistent because the service manual also says 3.0kgf-m and 21ft-lbs or b) they filled out the table with a formula based on the Nm values gently caress now I'm overthinking it. My last bike was 20Nm in the drain plug... ugh. I can't really loosen it and re-tighten it can I? Renaissance Robot fucked around with this message at 20:10 on Nov 7, 2019 |
# ? Nov 7, 2019 20:02 |
Do you guys think that when shops change your oil they're torquing the sump plug and poo poo? Cause I've got some news. Things worth torquing: cam and crank bearing screws, case bolts, head studs, nuts/bolts on the end of the crank/cam, USD fork pinch bolts, engine mounts, sometimes exhaust bolts. Everything else you do by feel or it would take like three weeks to do one job.
|
|
# ? Nov 7, 2019 20:15 |
|
For everything that's probably going to be opened up again at next year's service, I just do it until it stops coming easy and then another half turn.
|
# ? Nov 7, 2019 20:16 |
|
What’s the thread opinion on fumoto valves? Considering one just because I like the idea of using a hose to drain, and not having to worry about torquing the plug after every change is a plus.
|
# ? Nov 7, 2019 21:53 |
|
I'd be worried about it opening accidentally. That's about as (un)likely as having an issue torquing it or lining it up, but also more deadly if I'm doing speed and a rock hits that armature just right to give my rear wheel a bathing. Also in the UK you have the chav factor: some chav on the street will see the arm and open it because why not.
Azza Bamboo fucked around with this message at 22:07 on Nov 7, 2019 |
# ? Nov 7, 2019 22:03 |
Martytoof posted:What’s the thread opinion on fumoto valves? Considering one just because I like the idea of using a hose to drain, and not having to worry about torquing the plug after every change is a plus. They are awesome but don't work on every bike because sometimes they stick out dangerously low.
|
|
# ? Nov 7, 2019 22:06 |
|
How do you guys that don’t have access to hoses wash your bike? Can you just do a 2 bucket system of wash and rinse or something?
|
# ? Nov 8, 2019 02:13 |
|
What do you mean, "wash your bike?" (I have fairings so I just use quick detailer and a rag every so often, and I've cleaned my wheels with wheel cleaner and a brush like 2 times in 3.5 years. Been meaning to take all the fairings off and really do a deep cleaning though)
|
# ? Nov 8, 2019 02:26 |
|
Rolo posted:How do you guys that don’t have access to hoses wash your bike? Can you just do a 2 bucket system of wash and rinse or something? Does it not rain where you live?
|
# ? Nov 8, 2019 03:21 |
|
Finger Prince posted:Does it not rain where you live? Do you also never wash your towels because "hey, I'm the cleanest thing in my apartment when I get out of the shower! Every time I use my towel it must get cleaner"?
|
# ? Nov 8, 2019 03:39 |
|
Mirconium posted:Do you also never wash your towels because "hey, I'm the cleanest thing in my apartment when I get out of the shower! Every time I use my towel it must get cleaner"? Shower? I just ride my bike naked in the rain.
|
# ? Nov 8, 2019 04:22 |
|
Rolo posted:How do you guys that don’t have access to hoses wash your bike? Can you just do a 2 bucket system of wash and rinse or something? Car wash? The diy kind. Or a sprayer for $20 on amazon works fine.
|
# ? Nov 8, 2019 05:04 |
|
I'm also interested in Rolo's question. At my apartment I have my own garage but no access to a hose like a homeowner would have
|
# ? Nov 8, 2019 05:09 |
|
Yeah I’m in a parking garage with no hose. My unofficial plan is to just get two small buckets, have one be soap and one be rinse. Add a sponge and brush to the mix somewhere.
|
# ? Nov 8, 2019 05:14 |
|
Unless you’re an anal weirdo, I bet you’ll not want to do it that way a second time. Just go to a coin op self service car wash and don’t use the high pressure around bearings, seals, or electronics. Re: oil pan bolt: make sure you use a new copper crush washer every time and it’s kind of a safety that extends your “tight enough but not tight enough to strip threads/shear a bolt” window. HenryJLittlefinger fucked around with this message at 05:42 on Nov 8, 2019 |
# ? Nov 8, 2019 05:40 |
|
Two buckets is fine, yes. A bit of a chore when it comes rinsing as you might have to refill a few times, but do-able.
|
# ? Nov 8, 2019 08:10 |
|
Rolo posted:How do you guys that don’t have access to hoses wash your bike? Can you just do a 2 bucket system of wash and rinse or something? Trip to the self serve car wash to blast all the goop and grime off. Then two buckets, and a hand pump water sprayer to rinse. Now, I pay some guy with a van to do it and also check my oil/chain/lubes. Because he can do it while I’m working making the whole endeavour cash flow positive.
|
# ? Nov 8, 2019 08:50 |
|
A cheap set of soft paint brushes is useful, easier to get into various shapes than a sponge. Keep one brush for filthy areas and one for fairly clean body panels you don't want to scratch.
|
# ? Nov 8, 2019 09:06 |
|
And acf-50 will stop it rusting into a lump
|
# ? Nov 8, 2019 09:40 |
|
Renaissance Robot posted:Two buckets is fine, yes. A bit of a chore when it comes rinsing as you might have to refill a few times, but do-able. I feel like I’m just repeating myself but go to amazon, search sprayer and get whatever has decent reviews and is cheap. Ola posted:A cheap set of soft paint brushes is useful, easier to get into various shapes than a sponge. Keep one brush for filthy areas and one for fairly clean body panels you don't want to scratch. If you really want to get a bike clean, take the fairings off first. I don’t know why you’d really want this but if you did. Shelvocke posted:And acf-50 will stop it rusting into a lump This stuff is the best.
|
# ? Nov 8, 2019 15:12 |
|
I don’t need to take the fairings off and I’m not trying to get it show ready or anything. My bike fairings are white so I have to spot clean them pretty often during bug season but now the rest of it is due, especially before it gets much colder. I hadn’t tried a quarter op because all the ones in my area are totally run down. I do live in a big city so I’ll see if I can find a decent one and just amazon a nice drying shammy to bring with me. Otherwise I’ll just look into a sprayer/bucket. I wouldn’t mind the bucket because I’m like 15 steps and an elevator from where I’d be washing it.
|
# ? Nov 8, 2019 16:27 |
|
I've heard good things about using a garden sprayer, like one of these: For rinsing the bike after washing if you haven't got a hose.
|
# ? Nov 8, 2019 16:44 |
|
There are also battery powered pressure washers, both variants which you can feed from a bucket or has a fixed refillable supply. or you can take 50x trips to a self serve wash for the same price.
|
# ? Nov 8, 2019 17:44 |
|
I did some research and found a nice self serve wash riding distance from me, so I’m just gonna go check that out. Turns out Apple maps autocorrects “self serve car wash” to “car wash” and won’t let you change it back. Led me to believe that there were only major ride through brands like AutoBell.
|
# ? Nov 8, 2019 20:22 |
|
Coin op car wash is the term I usually see describing them
|
# ? Nov 8, 2019 20:44 |
|
That does work in maps without being replaced, so there you go. Gracias.
|
# ? Nov 8, 2019 21:20 |
|
Finger Prince posted:I've heard good things about using a garden sprayer, like one of these: This is what I do, works a treat. Rinse it, wash it, rinse it again.
|
# ? Nov 8, 2019 23:58 |
|
So absolutely zero of the coin op washes in my town show up on google. Makes me want to make an app (read: convince someone who knows how to make an app) that is a directory of coin op washes. After the drive thru one hosed up my trucks clear coat, I’m never doing that again. Also it never really gets the undercarriage clean.
|
# ? Nov 9, 2019 05:50 |
|
Quite specific electrics question, apologies for being a bore - I'm going to make an LED chip board to put in the tail light housing. There'll be two separate fused circuits; one for running tail light, and one for brake light. The rectified output of my stator is 12v, and I'm going to add a large capacitor to smooth out the supply. My plan is to use 6 X red LEDs in series each with a voltage drop of 2.2-2.4v. It means they'll be slightly under supplied at normal output but much better able to cope with a spike at higher RPM. My understanding is that I won't need to use a resistor in this circuit as the voltage will be shared equally between the components and well below the tolerance level. Is that correct?
|
# ? Nov 9, 2019 12:17 |
|
If no one in this thread answers your question, I’d bet the folks over here can!
|
# ? Nov 9, 2019 14:10 |
|
Martytoof posted:If no one in this thread answers your question, I’d bet the folks over here can! Thanks, you're right, I'll go over there
|
# ? Nov 9, 2019 15:12 |
|
Martytoof posted:If no one in this thread answers your question, I’d bet the folks over here can! Oh this is good, thanks for the link.
|
# ? Nov 9, 2019 16:04 |
|
What are the actual symptoms of a bike having too little battery capacity in terms of amp-hours if the cranking voltage is correct? Just dead battery more often?
|
# ? Nov 10, 2019 04:23 |
It'll go flat faster if you're trying to repeatedly start the bike, for one thing. It it's bad enough the bike might not even turn over.
|
|
# ? Nov 10, 2019 04:28 |
|
|
# ? May 16, 2024 05:56 |
|
If my motorcycle has a regular lead acid 6AH battery in it, and I replace it with a 9AH or 12AH lithium battery, it's not going to harm my motorcycle in any way is it?
|
# ? Nov 10, 2019 11:42 |